scholarly journals Influence of flux composition on the process of electroslag surfacing of end faces with discrete feeding of filler material

2018 ◽  
Vol 2018 (1) ◽  
pp. 44-49
Author(s):  
Yu.M. Kuskov ◽  
Keyword(s):  
Filler Material ◽  
Flux Composition

Production of Asbestos-free Brake Pad Using Groundnut Shell as Filler Material

2018 ◽  
Vol 4 (12) ◽  
Author(s):  
W. C. Solomon ◽  
M. T. Lilly ◽  
J. I. Sodiki
Keyword(s):  
Phenolic Resin ◽  
Cost Effective ◽  
Filler Material ◽  
Particle Sizes ◽  
Brake Pad ◽  
Brake Pads ◽  
Environmental Friendly ◽  
Sieve Size ◽  
Groundnut Shell ◽  
The Cost

The development and evaluation of brake pads using groundnut shell (GS) particles as substitute material for asbestos were carried out in this study. This was with a view to harnessing the properties of GS, which is largely deposited as waste, and in replacing asbestos which is carcinogenic in nature despite its good tribological and mechanical properties. Two sets of composite material were developed using varying particle sizes of GS as filler material, with phenolic resin as binder with percentage compositions of 45% and 50% respectively. Results obtained indicate that the compressive strength and density increase as the sieve size of the filler material decreases, while water and oil absorption rates increase with an increase in sieve size of GS particle. This study also indicates that the cost of producing brake pad can be reduced by 19.14 percent if GS is use as filler material in producing brake pad. The results when compared with those of asbestos and industrial waste showed that GS particle can be used as an effective replacement for asbestos in producing automobile brake pad. Unlike asbestos, GS-based brake pads are environmental friendly, biodegradable and cost effective.

Development of the brazing technique of W and JLF-1 by Ni-P filler material

2021 ◽  
Vol 170 ◽  
pp. 112687
Author(s):  
T. Yamashita ◽  
M. Tokitani ◽  
Y. Hamaji ◽  
H. Noto ◽  
S. Masuzaki ◽  
...  
Keyword(s):  
Filler Material

scholarly journals UPPER FILLER MATERIAL APPLIED IN CAVERN TYPE RADIOACTIVE WASTE DISPOSAL FACILITY

2016 ◽  
Vol 72 (3) ◽  
pp. 234-248
Author(s):  
Shin-ichi TAKECHI ◽  
Toshiyuki SASAKI ◽  
Kosuke YOKOZEKI ◽  
Hiroshi SHIMBO ◽  
Yoshihiro AKIYAMA ◽  
...  
Keyword(s):  
Radioactive Waste ◽  
Waste Disposal ◽  
Radioactive Waste Disposal ◽  
Filler Material ◽  
Disposal Facility

Mechanical properties of joints of 1460 aluminium alloy, produced by electron beam welding using filler material from 1201 alloy

2020 ◽  
Vol 2020 (12) ◽  
pp. 15-20
Author(s):  
V.V. Skryabinskyi ◽  
◽  
V.M. Nesterenkov ◽  
V.R. Strashko ◽  
◽  
...  
Keyword(s):  
Mechanical Properties ◽  
Electron Beam ◽  
Aluminium Alloy ◽  
Electron Beam Welding ◽  
Filler Material
Sign in / Sign up

Export Citation Format

Share Document