Protective Lite Rubberized Material Based on Chlorosulphonated Polyethylene with Increased Resistance to Aggressive Media and Open Flame

Author(s):  
Neil E. Coughlan ◽  
Ross N. Cuthbert ◽  
Eoghan M. Cunningham ◽  
Stephen Potts ◽  
Diarmuid McSweeney ◽  
...  

AbstractSuppression of established populations of invasive alien species can be a complex and expensive process, which is frequently unsuccessful. The Asian clam, Corbicula fluminea (Müller, 1774), is considered a high impact invader that can adversely alter freshwater ecosystems and decrease their socioeconomic value. To date, C. fluminea continues to spread and persist within freshwater environments worldwide, despite repeated management attempts to prevent dispersal and suppress established populations. As extensive C. fluminea beds can often become exposed during low-water conditions, the direct application of hot or cold thermal shock treatments has been proposed as suitable mechanism for their control. Further, mechanical substrate disturbance may enhance the efficacy of thermal shock treatments by facilitating exposures to multiple layers of buried clams. In the present study, we advanced these methods by assessing combined applications of both hot and cold thermal shock treatments for control of C. fluminea, using steam spray (≥100 °C; 350 kPa), low- or high-intensity open-flame burns (~1000 °C) and dry ice (−78 °C). In a direct comparison of raking combined with hot thermal shock applications, both steam and high-intensity open-flame treatments tended to be most effective, especially following multiple applications. In addition, when hot thermal treatments are followed by a final cold shock (i.e. dry ice), steam treatments tended to be most effective. Further, when dry ice was applied either alone or prior to an application of a hot shock treatment, substantial if not complete C. fluminea mortality was observed. Overall, this study demonstrated that combined applications of hot and cold thermal shock treatments, applied following the disruption of the substrate, can substantially increase C. fluminea mortality compared to separate hot or cold treatments.


Author(s):  
S. O. Gulyar ◽  
Yu. I. Strelchenko ◽  
V. M. Jelskyj

We developed a valid experimental model of dosed burn to study the influence of polarized light on burns, obtained from open flame, with a possibility of their basic parameters regulation. In the article there are characterized the expression and peculiarities of inflammation reaction process, development and dynamics of granulation growth and the process of burn wound epithelization. We observed polarized light positive influence on burn wound regeneration and speed of its healing. In particular, we singled out: derma depth alteration restriction and secondary alteration of skin tissues and sub muscles, activation of mechanisms, that restrict inflammation, fibroblasts proliferation increase, formation of granulations and neo-angiogenesis, stimulation of proliferation, keratinocytes' migration and wound surface epithelialization under the influence of polarized light. We singled out expressed antinociceptive, anti-stress and adaptive-stimulating effects of polarized light on central nervous system functional state at burns.


BioResources ◽  
2018 ◽  
Vol 13 (3) ◽  
pp. 6963-6969
Author(s):  
Higor Rogerio Favarim ◽  
Lucas Oliveira Leite

The aim of this paper was to investigate the influence of zinc oxide (ZnO) nanoparticles on the resistance of pine wood to fire and ultraviolet (UV) radiation. The ZnO nanoparticles were prepared from aqueous zinc nitrate via a proteic sol-gel method. Dried samples were impregnated using immersion in an aqueous solution of ZnO nanoparticles in the amount of 1 wt.% wood. Samples were exposed to an open flame to test the fire retardance, and a high-pressure UV lamp was used to test the UV resistance. The results showed an improvement in the fire retardance and UV radiation resistance after the impregnation of ZnO nanoparticles.


2011 ◽  
Vol 17 (3) ◽  
pp. 315-321 ◽  
Author(s):  
Gordana Markovic ◽  
Vojislav Jovanovic ◽  
Suzana Samarzija-Jovanovic ◽  
Milena Marinovic-Cincovic ◽  
Jaroslava Budinski-Simendic

In this paper the curing and mechanical properties of two series of prepared blends, i.e., chlorosulphonated polyethylene (CSM)/isobutylene-co-isoprene (IIR) rubber blends and chlorosulphonated polyethylene (CSM)/chlorinated isobutylene-co-isoprene (CIIR) rubber blends were carried out. Blends were prepared using a two roll-mill at a temperature of 40-50?C. The curing was assessed by using a Monsanto Oscillating Disc Rheometer R-100. The process of vulcanization accelerated sulfur of pure rubbers and their blends was carried out in an electrically heated laboratory hydraulic press under a pressure of about 4 MPa and 160?. The stress-strain experiments were performed using tensile tester machine (Zwick 1425). Results indicate that the scorch time, ts2 and optimum cure time, tc90 increase with increasing CSM content in both blends. The values of modulus at 100% and at 300% elongation and tensile strength increases with increasing CSM content, whereas elongation at break shows a decreasing trend. The enhancement in mechanical properties was supported by data of crosslink density in these samples obtained from swelling measurement and scanning electron microscopy studies of the rubber blends fractured surfaces.


1983 ◽  
Vol 53 (8) ◽  
pp. 475-482 ◽  
Author(s):  
Itzhak Shalev ◽  
Roger L. Barker
Keyword(s):  

2006 ◽  
Vol 234 ◽  
pp. S89 ◽  
Author(s):  
K.M. Yedinak ◽  
J.M. Forthofer ◽  
J.D. Cohen ◽  
M.A. Finney
Keyword(s):  

Author(s):  
Luca Casarsa ◽  
Diego Micheli ◽  
Valentino Pediroda ◽  
Robert Radu

An atmospheric combustor model with optical access for confined, non-premixed swirl-stabilized flames was developed in order to investigate the combustion behaviour of gas turbine flames fired with low-caloric syngases. The applied measuring techniques are Particle Image Velocimetry (PIV) for cold aerodynamic analysis, IR thermometry in open flame conditions, thermocouple traverses and global emissions analyzer in confined flame conditions. Two different fuels were chosen: propane and a synthetic mixture of CH4, CO, CO2, H2 having a composition typical of a gas from wood pyrolysis. Thermal powers between ∼5 kW and ∼20 kW were obtained with two different air flow rates and equivalence ratio varied in the range φ = 0.2–1.0. The experimental results constitute a database for the validation of numerical combustion models. Preliminary numerical analysis was carried out with STAR-CD software package.


Sign in / Sign up

Export Citation Format

Share Document