Effect of Creep and Oxidation on the Isothermal and Thermomechanical Fatigue Behavior of an Austenitic Stainless Steel

2012 ◽  
pp. 178-178-20
Author(s):  
Hans-Jürgen Christ ◽  
Valerij Bauer
Keyword(s):  
Stainless Steel ◽  
Austenitic Stainless Steel ◽  
Fatigue Behavior ◽  
Thermomechanical Fatigue

Effect of Creep and Oxidation on the Isothermal and Thermomechanical Fatigue Behavior of an Austenitic Stainless Steel

2011 ◽  
Vol 8 (8) ◽  
pp. 103557
Author(s):  
Hans-Jürgen Christ ◽  
Valerij Bauer ◽  
A. Saxena ◽  
B. Dogan ◽  
S. W. Dean
Keyword(s):  
Stainless Steel ◽  
Austenitic Stainless Steel ◽  
Fatigue Behavior ◽  
Thermomechanical Fatigue

Biaxial thermomechanical fatigue on a 304L-type austenitic stainless steel*

2006 ◽  
Vol 48 (1-2) ◽  
pp. 44-49
Author(s):  
Valérie Maillot ◽  
Gérard Degallaix ◽  
Suzanne Degallaix ◽  
Antoine Fissolo
Keyword(s):  
Stainless Steel ◽  
Austenitic Stainless Steel ◽  
Thermomechanical Fatigue

Effects of Surface Finish and Loading Conditions on the Low Cycle Fatigue Behavior of Austenitic Stainless Steel in PWR Environment for Various Strain Amplitude Levels

2009 ◽  
Author(s):  
Jean Alain Le Duff ◽  
Andre´ Lefranc¸ois ◽  
Jean Philippe Vernot
Keyword(s):  
Stainless Steel ◽  
Austenitic Stainless Steel ◽  
Strain Amplitude ◽  
Surface Finish ◽  
Low Cycle Fatigue ◽  
Fatigue Behavior ◽  
Complex Loading ◽  
Loading Conditions ◽  
Test Results ◽  
Cycle Fatigue

In February/March 2007, The NRC issued Regulatory Guide “RG1.207” and Argonne National Laboratory issued NUREG/CR-6909 that is now applicable in the US for evaluations of PWR environmental effects in fatigue analyses of new reactor components. In order to assess the conservativeness of the application of this NUREG report, Low Cycle Fatigue (LCF) tests were performed by AREVA NP on austenitic stainless steel specimens in a PWR environment. The selected material exhibits in air environment a fatigue behavior consistent with the ANL reference “air” mean curve, as published in NUREG/CR-6909. LCF tests in a PWR environment were performed at various strain amplitude levels (± 0.6% or ± 0.3%) for two loading conditions corresponding to a simple or to a complex strain rate history. The simple loading condition is a fully reverse triangle signal (for comparison purposes with tests performed by other laboratories with the same loading conditions) and the complex signal simulates the strain variation for an actual typical PWR thermal transient. In addition, two various surface finish conditions were tested: polished and ground. This paper presents the comparisons of penalty factors, as observed experimentally, with penalty factors evaluated using ANL formulations (considering the strain integral method for complex loading), and on the other, the comparison of the actual fatigue life of the specimen with the fatigue life predicted through the NUREG report application. For the two strain amplitudes of ± 0.6% and ± 0.3%, LCF tests results obtained on austenitic stainless steel specimens in PWR environment with triangle waveforms at constant low strain rates give “Fen” penalty factors close to those estimated using the ANL formulation (NUREG/6909). However, for the lower strain amplitude level and a triangle loading signal, the ANL formulation is pessimistic compared to the AREVA NP test results obtained for polished specimens. Finally, it was observed that constant amplitude LCF test results obtained on ground specimens under complex loading simulating an actual sequence of a cold and hot thermal shock exhibits lower combined environmental and surface finish effects when compared to the penalty factors estimated on the basis of the ANL formulations. It appears that the application of the NUREG/CR-6909 in conjunction with the Fen model proposed by ANL for austenitic stainless steel provides excessive margins, whereas the current ASME approach seems sufficient to cover significant environmental effects for representative loadings and surface finish conditions of reactor components.

Torsional thermomechanical fatigue behavior of 316LN stainless steel

2020 ◽  
Vol 789 ◽  
pp. 139676 ◽  
Author(s):  
Bingbing Li ◽  
Yiming Zheng ◽  
Caiming Liu ◽  
Qite Li ◽  
Zhe Zhang ◽  
...  
Keyword(s):  
Stainless Steel ◽  
Fatigue Behavior ◽  
Thermomechanical Fatigue ◽  
316Ln Stainless Steel
Sign in / Sign up

Export Citation Format

Share Document