Dielectric Measurements on Plastics at High Temperatures

2009 ◽  
pp. 15-15-16 ◽  
Author(s):  
Thomas Hazen
Keyword(s):  
High Temperatures ◽  
Dielectric Measurements

A New Approach For Dielectric Measurements At High Temperatures

1996 ◽  
Vol 430 ◽  
Author(s):  
C. Groffils ◽  
P. J. Luypaert ◽  
Y. Zhou ◽  
O. Van der Biest
Keyword(s):  
Perturbation Method ◽  
High Temperatures ◽  
Dielectric Constants ◽  
Dielectric Measurements ◽  
New Approach ◽  
Extraction Algorithm ◽  
Frequency Scan ◽  
Different Temperatures ◽  
Cold Cavity ◽  
Full Network

AbstractMost of the algorithms for cavity dielectric measurements use a full network frequency scan for the perturbation method. At high temperature the measurement points in one frequency scan will have different temperatures due to the fast cooling of the sample inside the cold cavity. This paper presents a new approach for the perturbation method to measure dielectric constants at high temperatures with a two port, two piston cylindrical cavity and external furnace. Special features of this cavity are the possibility to work with different modes and different relative positions of the coupling aperture.The dielectric properties are extracted from the full sets of S-parameters for two successive frequency points corresponding to approximately the same temperatures. An extraction algorithm is developed and programmed.

In situ REM imaging of surface processes on ceramic bulk crystals from 300 to 1670 K in a conventional TEM

1991 ◽  
Vol 49 ◽  
pp. 660-661
Author(s):  
Z. L. Wang ◽  
J. Bentley
Keyword(s):  
High Temperatures ◽  
Image Resolution ◽  
Atomic Processes ◽  
Crystal Surfaces ◽  
Beam Radiation ◽  
Surface Areas ◽  
Transmission Electron ◽  
Reflection Electron Microscopy ◽  
Gas Reactions

Studying the behavior of surfaces at high temperatures is of great importance for understanding the properties of ceramics and associated surface-gas reactions. Atomic processes occurring on bulk crystal surfaces at high temperatures can be recorded by reflection electron microscopy (REM) in a conventional transmission electron microscope (TEM) with relatively high resolution, because REM is especially sensitive to atomic-height steps.Improved REM image resolution with a FEG: Cleaved surfaces of a-alumina (012) exhibit atomic flatness with steps of height about 5 Å, determined by reference to a screw (or near screw) dislocation with a presumed Burgers vector of b = (1/3)<012> (see Fig. 1). Steps of heights less than about 0.8 Å can be clearly resolved only with a field emission gun (FEG) (Fig. 2). The small steps are formed by the surface oscillating between the closely packed O and Al stacking layers. The bands of dark contrast (Fig. 2b) are the result of beam radiation damage to surface areas initially terminated with O ions.

High Temperature n- and p-type Doped Microcrystalline Silicon Layers Grown by VHF PECVD Layer-by-Layer Deposition

2003 ◽  
Vol 762 ◽  
Author(s):  
A. Gordijn ◽  
J.K. Rath ◽  
R.E.I. Schropp
Keyword(s):  
Activation Energy ◽  
High Temperature ◽  
High Temperatures ◽  
Continuous Wave ◽  
Hydrogen Plasma ◽  
Silicon Layer ◽  
Dark Conductivity ◽  
High Deposition Rate ◽  
Layer By Layer ◽  
Microcrystalline Silicon

AbstractDue to the high temperatures used for high deposition rate microcrystalline (μc-Si:H) and polycrystalline silicon, there is a need for compact and temperature-stable doped layers. In this study we report on films grown by the layer-by-layer method (LbL) using VHF PECVD. Growth of an amorphous silicon layer is alternated by a hydrogen plasma treatment. In LbL, the surface reactions are separated time-wise from the nucleation in the bulk. We observed that it is possible to incorporate dopant atoms in the layer, without disturbing the nucleation. Even at high substrate temperatures (up to 400°C) doped layers can be made microcrystalline. At these temperatures, in the continuous wave case, crystallinity is hindered, which is generally attributed to the out-diffusion of hydrogen from the surface and the presence of impurities (dopants).We observe that the parameter window for the treatment time for p-layers is smaller compared to n-layers. Moreover we observe that for high temperatures, the nucleation of p-layers is more adversely affected than for n-layers. Thin, doped layers have been structurally, optically and electrically characterized. The best n-layer made at 400°C, with a thickness of only 31 nm, had an activation energy of 0.056 eV and a dark conductivity of 2.7 S/cm, while the best p-layer made at 350°C, with a thickness of 29 nm, had an activation energy of 0.11 V and a dark conductivity of 0.1 S/cm. The suitability of these high temperature n-layers has been demonstrated in an n-i-p microcrystalline silicon solar cell with an unoptimized μc-Si:H i-layer deposited at 250°C and without buffer. The Voc of the cell is 0.48 V and the fill factor is 70 %.

Sign in / Sign up

Export Citation Format

Share Document