Shear Strength Properties of Some Deep-Sea Pelagic Sediments

2008 ◽  
pp. 251-251-7 ◽  
Author(s):  
I Noorany
Keyword(s):  
Shear Strength ◽  
Deep Sea ◽  
Strength Properties

scholarly journals Comparative Analysis of Shear Strength Parallel to Fiber of Different Local Bamboo Species in the Philippines

2021 ◽  
Vol 13 (15) ◽  
pp. 8164
Author(s):  
Brian E. Bautista ◽  
Lessandro E. O. Garciano ◽  
Luis F. Lopez
Keyword(s):  
Mechanical Properties ◽  
Shear Strength ◽  
Comparative Analysis ◽  
Strength Properties ◽  
The Philippines ◽  
Bamboo Species ◽  
Test Protocol ◽  
Future Design ◽  
Average Shear Strength ◽  
Bambusa Vulgaris

There are limited published studies related to the mechanical properties of bamboo species in the Philippines. In this study, the shear strength properties of some economically viable bamboo species in the Philippines were properly characterized based on 220 shear test results. The rationales of selecting this mechanical property are the following: (1) Shear strength, parallel to the fiber, has the highest variability among the mechanical properties; and (2) Shear is one of the governing forces on joint connections, and such connections are the points of failure on bamboo structures when subjected to extreme loading conditions. ISO 22157-1 (2017) test protocol for shear was used for all tests. The results showed that Bambusa blumeana has the highest average shear strength, followed by Gigantochloa apus, Dendrocalamus asper, Bambusa philippinensis, and Bambusa vulgaris. However, comparative analysis, using One-way ANOVA, showed that shear strength values among these bamboo species have significant differences statistically. A linear regression model is also established to estimate the shear strength of bamboo from the physical properties. Characteristic shear strength is also determined using ISO 12122-1 (2014) for future design reference.

scholarly journals Improved strength properties of LVL glued using PVAc adhesives with physical treatment-based Rubberwood (Hevea brasiliensis)

2020 ◽  
Vol 5 (1) ◽  
pp. 711-725
Author(s):  
Sutrisno ◽  
Eka Mulya Alamsyah ◽  
Ginanjar Gumilar ◽  
Takashi Tanaka ◽  
Masaaki Yamada
Keyword(s):  
Shear Strength ◽  
Hevea Brasiliensis ◽  
Formaldehyde Emission ◽  
Strength Properties ◽  
Modulus Of Rupture ◽  
Horizontal Shear ◽  
Physical Treatment ◽  
Cold Pressing ◽  
Laminated Veneer Lumber ◽  
Pressing Time

AbstractThe properties of the laminated veneer lumber (LVL) composed of the boiled veneer of Rubberwood (Hevea brasiliensis) using polyvinyl acetate (PVAc) adhesives in various cold-pressing time and various conditioned time with loaded and unloaded were studied. Five-ply LVL was produced by boiling veneer at 100°C for 90 min as pretreatment and cold-pressing time at 12 kgf cm−2 for 1.5, 6, 18, and 24 h then conditioned at 20°C and 65% relative humidity (RH) with loaded (12 kgf cm−2) and unloaded for 7 days as physical treatment. Especially for the delamination test, the specimens were immersed at 70 ± 3°C for 2 h and dried in the oven at 60 ± 3°C for 24 h; then, the specimens were solidified at room temperature (20°C and 65% RH) with loaded (12 kgf cm−2) and unloaded for 7, 10, 12, and 14 days. To determine the performance of LVL, the density, moisture content (MC), delamination, modulus of elasticity (MOE), modulus of rupture (MOR), horizontal shear strength, and formaldehyde emission tests were conducted according to the Japanese Agricultural Standard (JAS 2008) for structural LVL. The MOE and MOR values were significantly influenced by the physical treatment, however, neither to horizontal shear strength nor to formaldehyde emission. The best performance of LVL has resulted from unloaded LVL with cold-pressed time for 18 h; the MOE and MOR values were 9,345.05 ± 141.61 N mm−2 and 80.67 ± 1.77 N mm−2, respectively. The best value of the horizontal shear strength was obtained from the LVL with 18 h cold-pressing time and conditioned with loaded (13.10 ± 1.47 N mm−2) and unloaded (12.23 ± 1.36 N mm−2). The percentage of delamination values decreased with an increase in the cold-pressing time and conditioning time. The lowest value of delamination (19.06%) was obtained from the LVL with 24 h cold-pressing time and conditioned with loaded for 14 days. Except the delamination test, all other properties fulfilled the JAS.

Shear strength properties of plain and spirally profiled cable bolts

2015 ◽  
Vol 52 (10) ◽  
pp. 1490-1495 ◽  
Author(s):  
Naj Aziz ◽  
Ali Mirzaghorbanali ◽  
Jan Nemcik ◽  
Kay Heemann ◽  
Stefan Mayer
Keyword(s):  
Shear Strength ◽  
Testing Machine ◽  
Peak Load ◽  
Strength Properties ◽  
Shear Displacement ◽  
Vertical Shear ◽  
Cross Sectional ◽  
Cable Bolts ◽  
Strength Capacity ◽  
Cable Bolt

An experimental investigation into the performance of two 22 mm diameter, 60 t tensile strength capacity Hilti cable bolts in shear was conducted using the double-shear testing apparatus at the laboratory of the School of Civil, Mining and Environmental Engineering, Faculty of Engineering and Information Sciences, University of Wollongong. The tested cable bolts were (i) Hilti 19 wire HTT-UXG plain strand and (ii) Hilti 19 wire HTT-IXG spirally profiled (smaller cross-sectional area than the plain one) cable bolt, with indentation only on the surface of the outer strands. These cable bolts are of sealed wire construction type, consisting of an outer 5.5 mm diameter wire layer overlying the middle 3 mm diameter wire strands. Both layers are wrapped around a single solid 7 mm diameter strand wire core. The double-shearing test was carried out in 40 MPa concrete blocks, contained in concrete moulds. Cable bolts were encapsulated in concrete using Orica FB400 pumpable grout. Prior to encapsulation, each cable bolt was pre-tensioned initially to 50 kN axial force. A 500 t capacity servocontrolled compression testing machine was used for both tests, and during each test the vertical shear displacement was limited to 70 mm of travel. The rate of vertical shear displacement was maintained constant at 1 mm/min. The maximum shear load achieved for the plain strand cable was 1024 kN, while the spiral cable peak load was 904 kN, before the cable bolt wires began to individually snap, leading to the cable bolt break-up into two sections. It is apparent that spiral profiles of the outer wires weaken both the tensile and shearing strength. Finally, another set of tests was undertaken using the British Standard single-shear approach, producing lower shear strength values.

Fundamental Shear-Strength Properties of the Lilla Edet Clay

Géotechnique ◽  
1960 ◽  
Vol 10 (3) ◽  
pp. 101-109 ◽  
Author(s):  
Laurits Bjerrum ◽  
Tien-Hsing Wu
Keyword(s):  
Shear Strength ◽  
Strength Properties
Sign in / Sign up

Export Citation Format

Share Document