Fatigue Behavior of Cyclically Softening and Hardening Steels Under Multiaxial Elastic-Plastic Deformation

2008 ◽  
pp. 586-586-20 ◽  
Author(s):  
CM Sonsino ◽  
V Grubisic
Keyword(s):  
Plastic Deformation ◽  
Fatigue Behavior ◽  
Elastic Plastic

Friction Force and Stresses Analysis for Contact of Assembled Details

2006 ◽  
Vol 113 ◽  
pp. 334-338
Author(s):  
Z. Dreija ◽  
O. Liniņš ◽  
Fr. Sudnieks ◽  
N. Mozga
Keyword(s):  
Mechanical Properties ◽  
Surface Roughness ◽  
Plastic Deformation ◽  
Friction Force ◽  
Sliding Friction ◽  
Friction Model ◽  
Contact Interface ◽  
Finite Element Program ◽  
Elastic Plastic ◽  
Element Program

The present work deals with the computation of surface stresses and deformation in the presence of friction. The evaluation of the elastic-plastic contact is analyzed revealing three distinct stages that range from fully elastic through elastic-plastic to fully plastic contact interface. Several factors of sliding friction model are discussed: surface roughness, mechanical properties and contact load and areas that have strong effect on the friction force. The critical interference that marks the transition from elastic to elastic- plastic and plastic deformation is found out and its connection with plasticity index. A finite element program for determination contact analysis of the assembled details and due to details of deformation that arose a normal and tangencial stress is used.

scholarly journals Influence of turning tool wear on the surface integrity and anti-fatigue behavior of Ti1023

2021 ◽  
Vol 13 (4) ◽  
pp. 168781402110112
Author(s):  
Li Xun ◽  
Wang Ziming ◽  
Yang Shenliang ◽  
Guo Zhiyuan ◽  
Zhou Yongxin ◽  
...  
Keyword(s):  
Surface Roughness ◽  
Plastic Deformation ◽  
Titanium Alloy ◽  
Fatigue Life ◽  
Tool Wear ◽  
Surface Integrity ◽  
Low Cycle Fatigue ◽  
Fatigue Behavior ◽  
Machined Surface ◽  
Deformation Layer

Titanium alloy Ti1023 is a typical difficult-to-cut material. Tool wear is easy to occur in machining Ti1023, which has a significant negative effect on surface integrity. Turning is one of the common methods to machine Ti1023 parts and machined surface integrity has a direct influence on the fatigue life of parts. To control surface integrity and improve anti-fatigue behavior of Ti1023 parts, it has an important significance to study the influence of tool wear on the surface integrity and fatigue life of Ti1023 in turning. Therefore, the effect of tool wear on the surface roughness, microhardness, residual stress, and plastic deformation layer of Ti1023 workpieces by turning and low-cycle fatigue tests were studied. Meanwhile, the influence mechanism of surface integrity on anti-fatigue behavior also was analyzed. The experimental results show that the change of surface roughness caused by worn tools has the most influence on anti-fatigue behavior when the tool wear VB is from 0.05 to 0.25 mm. On the other hand, the plastic deformation layer on the machined surface could properly improve the anti-fatigue behavior of specimens that were proved in the experiments. However, the higher surface roughness and significant surface defects on surface machined utilizing the worn tool with VB = 0.30 mm, which leads the anti-fatigue behavior of specimens to decrease sharply. Therefore, to ensure the anti-fatigue behavior of parts, the value of turning tool wear VB must be rigorously controlled under 0.30 mm during finishing machining of titanium alloy Ti1023.

Energy storage and dissipation of elastic-plastic deformation under shock compression: Simulation and Analysis

2021 ◽  
Vol 158 ◽  
pp. 103876
Author(s):  
Qi-lin Xiong ◽  
Zhenhuan Li ◽  
Takahiro Shimada ◽  
Takayuki Kitamura
Keyword(s):  
Plastic Deformation ◽  
Energy Storage ◽  
Shock Compression ◽  
Elastic Plastic

Virtual Material Model of Joint Interfaces Considering Elastic-Plastic Deformation of Asperities

2013 ◽  
Vol 457-458 ◽  
pp. 257-261
Author(s):  
Li Gang Cai ◽  
Teng Yun Xu ◽  
Yong Sheng Zhao
Keyword(s):  
Plastic Deformation ◽  
Elastic Modulus ◽  
Fractal Theory ◽  
Material Model ◽  
Contact Theory ◽  
Hertz Contact ◽  
Calculation Methods ◽  
Elastic Plastic ◽  
Element Simulation ◽  
Simulation Results

A virtual material model of joint interfaces was established based on the Hertz contact theory and fractal theory, this model was improved by considering the influence of the elastic-plastic deformation of asperities and ameliorating the calculation methods of the elastic modulus. The simulation results of elastic-plastic considered and elastic-plastic unconsidered were compared, moreover, the finite element simulation results and experimental results were compared to fully explain the necessity of considering the influence of the elastic-plastic deformation and the the correctness of the method to calculate the elastic modulus. The research suggested that under a same load the elastic modulus of the model considering the influence of the elastic-plastic deformation was slightly larger than the un considering one, which means it could describe the characteristics of joint interfaces more accurately.

Sign in / Sign up

Export Citation Format

Share Document