Strain Energy Release Rate for a Crack Under Combined Mode I and Mode II

2009 ◽  
pp. 2-2-27 ◽  
Author(s):  
MA Hussain ◽  
SL Pu ◽  
J Underwood
Keyword(s):  
Energy Release Rate ◽  
Energy Release ◽  
Release Rate ◽  
Strain Energy ◽  
Strain Energy Release Rate ◽  
Strain Energy Release ◽  
Mode I ◽  
Mode Ii ◽  
Combined Mode

The Edge Delamination Test: Measuring the Critical Adhesion Energy of Thin-Film Coatings, Part II: Mode Mixity & Application

1994 ◽  
Vol 338 ◽  
Author(s):  
Edward O. Shaffer ◽  
Scott A. Sikorski ◽  
Frederick J. McGarry
Keyword(s):  
Thin Film ◽  
Energy Release Rate ◽  
Energy Release ◽  
Release Rate ◽  
Strain Energy ◽  
Strain Energy Release Rate ◽  
Strain Energy Release ◽  
Mode I ◽  
Rigid Substrate ◽  
Edge Delamination

ABSTRACTThe edge delamination test (EDT) is being developed to measure the critical energy required to cause a thin film, under biaxial tensile stress, to debond from a rigid substrate[1]. The test uses circular features etched through biaxially stressed films adhered to a rigid substrate. If the stress is large enough, a stable debond ring grows radially about the feature. We use a finite element analysis to model the test, solving for the applied strain energy release rate as a function of crack length, feature hole radius and other geometrical parameters. The model identifies both mode I and mode II components of the strain energy release rate, and agrees with previous analytical solutions for the total debond energy. However, the model predicts, with a very refined mesh at the crack tip, the fracture process is pure mode I. To explore this result, critical strain energy release rates from the EDT and the island blister test (IBT) are compared. This agreement supports the model prediction that the failure process in the EDT is modeI peeling.

Strain Energy Release Rate Determination in the Case of Mode II Crack in Overhanging Bilayered Composite Beam

2013 ◽  
Vol 43 (3) ◽  
pp. 87-96
Author(s):  
Victor I. Rizov ◽  
Angel S. Mladensky
Keyword(s):  
Energy Release Rate ◽  
Energy Release ◽  
Release Rate ◽  
Composite Beam ◽  
Strain Energy ◽  
Strain Energy Release Rate ◽  
Rectangular Cross Section ◽  
Strain Energy Release ◽  
Mode Ii ◽  
Mode Ii Crack

Abstract Mode II crack in overhanging bilayered composite beam is investigated. The beam has rectangular cross-section and is made by two unidirectional fiber reinforced composites. The formula for strain energy release rate, G, is obtained by linear elastic fracture mechanics compliance technique. The validity of the expression derived is established by comparison with solution for G in which the internal forces in front and behind the crack tip are used. The influence of the two layers moduli of elasticity ratio on the strain energy release rate is investigated. The dependence among the strain energy release rate and the ratio of the lengths of the overhang beam part and the beam span is also analyzed.

Delamination Strain Energy Release Rate in Carbon Fiber/Epoxy Resin Composites

2007 ◽  
Vol 555 ◽  
pp. 515-519 ◽  
Author(s):  
M.V. Gordić ◽  
I.M. Djordjević ◽  
D.R. Sekulić ◽  
Z.S. Petrović ◽  
M.M. Stevanović
Keyword(s):  
Energy Release Rate ◽  
Epoxy Resin ◽  
Energy Release ◽  
Release Rate ◽  
Strain Energy ◽  
Strain Energy Release Rate ◽  
Strain Energy Release ◽  
Mode I ◽  
Resin Composites ◽  
Epoxy Resin Composites

The paper reports on an experimental study of the Mode I interlaminar fracture of unidirectional carbon fibers/epoxy resin composites. Mode I delamination strain energy release rate GIC was determined in double cantilever beam (DCB) test, before and after gamma irradiation at various doses. Glass transition temperature, Tg of epoxy matrix was determined from dynamic mechanical measurements. The delamination surfaces of tested coupons were observed by scanning electron microscopy. The variations in GIC values were correlated with irradiation doses, Tg values and the features of delamination microfractographs, as well as with the variation under irradiation of matrix or fibre/matrix dominated mechanical properties.

scholarly journals Analysis of Mixed Mode I/II/III Fracture in Foam Core Sandwich Structures Using Imposed Displacement Split Cantilever Beams

2015 ◽  
Vol 45 (3) ◽  
pp. 69-82
Author(s):  
V. Rizov
Keyword(s):  
Finite Element ◽  
Energy Release Rate ◽  
Energy Release ◽  
Release Rate ◽  
Mixed Mode ◽  
Strain Energy ◽  
Strain Energy Release Rate ◽  
Strain Energy Release ◽  
Mode I ◽  
Foam Core

Abstract Static fracture in foam core sandwich structures under mixed mode I/II/III loading conditions was studied theoretically. In order to generate such loading conditions, a thread guide was used to impose in- plane displacements of the lower crack arm of a sandwich Split Cantilever Beam (SCB). The upper crack arm was loaded by a transverse force. A three-dimensional finite element model of the imposed displacement sandwich SCB configuration was developed. The fracture was studied applying the concepts of linear-elastic fracture mechanics. The strain energy release rate mode components distribution along the crack front was analyzed using the virtual crack closure technique. The influence of the imposed displacement magnitude and the crack length on the fracture was evaluated. The effect of the sandwich core material on the mixed-mode I/II/III fracture was studied. For this purpose, finite element simulations were carried-out assuming that the core is made by different rigid cellular foams. It was found that the strain energy release rate decreases when the foam density increases.

scholarly journals Computation of mode I strain energy release rate of symmetrical and asymmetrical sandwich structures using mixed finite element

2021 ◽  
Vol 15 (56) ◽  
pp. 229-239
Author(s):  
Amina Mohamed Ben Ali ◽  
Salah Bouziane ◽  
Hamoudi Bouzerd
Keyword(s):  
Finite Element ◽  
Energy Release Rate ◽  
Energy Release ◽  
Release Rate ◽  
Strain Energy ◽  
Strain Energy Release Rate ◽  
Double Cantilever Beam ◽  
Mixed Finite Element ◽  
Strain Energy Release ◽  
Mode I

The use of composite materials is on the rise in different engineering fields, the main advantage of these materials for the aerospace industry is their low weight for excellent mechanical qualities. The analysis of failure modes, such as delamination, of these materials has received great attention from researchers. This paper proposes a method to evaluate the mode I Strain Energy Release Rate (SERR) of sandwich structures. This method associated a two-dimensional mixed finite element with virtual crack extension technique for the analysis of interfacial delamination of sandwich beams. A symmetrical Double Cantilever Beam (DCB) and asymmetrical Double Cantilever Beam (UDCB) have been analyzed in this study.  The comparison of the results obtained by this method and those found in the literature shows efficiency and good precision for the calculation of Strain Energy Release Rate (SERR).

Sign in / Sign up

Export Citation Format

Share Document