Effect of Ion Implantation on Fretting Fatigue in Ti-6Al-4V Alloy

2009 ◽  
pp. 138-138-12 ◽  
Author(s):  
RG Vardiman ◽  
D Creighton ◽  
G Salivar ◽  
A Effatian ◽  
BB Rath
Keyword(s):  
Ion Implantation ◽  
Fretting Fatigue

Optimising Ion Implantation Conditions for Improving Wear, Fatigue, and Fretting Fatigue Of Ti-6Ai-4V

1989 ◽  
Vol 5 (1) ◽  
pp. 55-79 ◽  
Author(s):  
J. E. Elder ◽  
R. Thamburaj ◽  
P. C. Patnaik
Keyword(s):  
Ion Implantation ◽  
Fretting Fatigue

Electron Diffraction Analysis of Microtwin Structures in Regrown (III) Silicon

1982 ◽  
Vol 40 ◽  
pp. 460-461
Author(s):  
P. Ling ◽  
R. Gronsky ◽  
J. Washburn
Keyword(s):  
Electron Diffraction ◽  
Ion Implantation ◽  
Diffraction Analysis ◽  
Diffraction Pattern ◽  
Direct Consequence ◽  
The Other ◽  
Electron Diffraction Analysis ◽  
Defect Microstructures ◽  
Ion Implanted

The defect microstructures of Si arising from ion implantation and subsequent regrowth for a (111) substrate have been found to be dominated by microtwins. Figure 1(a) is a typical diffraction pattern of annealed ion-implanted (111) Si showing two groups of extra diffraction spots; one at positions (m, n integers), the other at adjacent positions between <000> and <220>. The object of the present paper is to show that these extra reflections are a direct consequence of the microtwins in the material.

Interlayer mixing in GaAs/AlxGa1-xAs heterostructures as a result of Se+ ion implantation

1988 ◽  
Vol 46 ◽  
pp. 908-909
Author(s):  
E.G. Bithell ◽  
W.M. Stobbs
Keyword(s):  
Ion Implantation ◽  
Diffusion Coefficients ◽  
Dark Field ◽  
Atomic Mass ◽  
Composition Profile ◽  
Semiconductor Heterostructures ◽  
Transmission Electron ◽  
Microscope Images ◽  
Damage Process ◽  
Electron Energy Loss

It is well known that the microstructural consequences of the ion implantation of semiconductor heterostructures can be severe: amorphisation of the damaged region is possible, and layer intermixing can result both from the original damage process and from the enhancement of the diffusion coefficients for the constituents of the original composition profile. A very large number of variables are involved (the atomic mass of the target, the mass and energy of the implant species, the flux and the total dose, the substrate temperature etc.) so that experimental data are needed despite the existence of relatively well developed models for the implantation process. A major difficulty is that conventional techniques (e.g. electron energy loss spectroscopy) have inadequate resolution for the quantification of any changes in the composition profile of fine scale multilayers. However we have demonstrated that the measurement of 002 dark field intensities in transmission electron microscope images of GaAs / AlxGa1_xAs heterostructures can allow the measurement of the local Al / Ga ratio.

Dynamic studies of silicide-mediated crystallization of amorphous silicon

1992 ◽  
Vol 50 (2) ◽  
pp. 1352-1353
Author(s):  
C. Hayzelden ◽  
J. L. Batstone
Keyword(s):  
Ion Implantation ◽  
Solid Phase ◽  
Metallic Phase ◽  
Single Crystal Substrate ◽  
Free Electrons ◽  
Melt Temperature ◽  
Transmission Electron ◽  
Crystal Substrate ◽  
High Resolution Tem

Epitaxial reordering of amorphous Si(a-Si) on an underlying single-crystal substrate occurs well below the melt temperature by the process of solid phase epitaxial growth (SPEG). Growth of crystalline Si(c-Si) is known to be enhanced by the presence of small amounts of a metallic phase, presumably due to an interaction of the free electrons of the metal with the covalent Si bonds near the growing interface. Ion implantation of Ni was shown to lower the crystallization temperature of an a-Si thin film by approximately 200°C. Using in situ transmission electron microscopy (TEM), precipitates of NiSi2 formed within the a-Si film during annealing, were observed to migrate, leaving a trail of epitaxial c-Si. High resolution TEM revealed an epitaxial NiSi2/Si(l11) interface which was Type A. We discuss here the enhanced nucleation of c-Si and subsequent silicide-mediated SPEG of Ni-implanted a-Si.Thin films of a-Si, 950 Å thick, were deposited onto Si(100) wafers capped with 1000Å of a-SiO2. Ion implantation produced sharply peaked Ni concentrations of 4×l020 and 2×l021 ions cm−3, in the center of the films.

Analysis of Silicon-On-Insulator Structures Formed By Oxygen Ion Implantation

1985 ◽  
Vol 43 ◽  
pp. 300-301
Author(s):  
N. Lewis ◽  
E. L. Hall ◽  
A. Mogro-Campero ◽  
R. P. Love
Keyword(s):  
Ion Implantation ◽  
Single Crystal ◽  
Single Crystal Silicon ◽  
Silicon Layer ◽  
Device Fabrication ◽  
Silicon On Insulator ◽  
High Dose ◽  
Crystal Silicon ◽  
Oxygen Ion ◽  
Oxygen Ion Implantation

The formation of buried oxide structures in single crystal silicon by high-dose oxygen ion implantation has received considerable attention recently for applications in advanced electronic device fabrication. This process is performed in a vacuum, and under the proper implantation conditions results in a silicon-on-insulator (SOI) structure with a top single crystal silicon layer on an amorphous silicon dioxide layer. The top Si layer has the same orientation as the silicon substrate. The quality of the outermost portion of the Si top layer is important in device fabrication since it either can be used directly to build devices, or epitaxial Si may be grown on this layer. Therefore, careful characterization of the results of the ion implantation process is essential.

Layered and ion implantation specimens as possible reference materials for the electron-probe microanalysis

1992 ◽  
Vol 50 (2) ◽  
pp. 1652-1653
Author(s):  
G. Remond ◽  
R.H. Packwood ◽  
C. Gilles ◽  
S. Chryssoulis
Keyword(s):  
Ion Implantation ◽  
Reference Materials ◽  
Analytical Techniques ◽  
Thin Film Deposition ◽  
Film Deposition ◽  
X Ray ◽  
Spatially Resolved ◽  
Analytical Expressions ◽  
Original Approach ◽  
Depth Concentration

Merits and limitations of layered and ion implanted specimens as possible reference materials to calibrate spatially resolved analytical techniques are discussed and illustrated for the case of gold analysis in minerals by means of x-ray spectrometry with the EPMA. To overcome the random heterogeneities of minerals, thin film deposition and ion implantation may offer an original approach to the manufacture of controlled concentration/ distribution reference materials for quantification of trace elements with the same matrix as the unknown.In order to evaluate the accuracy of data obtained by EPMA we have compared measured and calculated x-ray intensities for homogeneous and heterogeneous specimens. Au Lα and Au Mα x-ray intensities were recorded at various electron beam energies, and hence at various sampling depths, for gold coated and gold implanted specimens. X-ray intensity calculations are based on the use of analytical expressions for both the depth ionization Φ (ρz) and the depth concentration C (ρz) distributions respectively.

The Effects of Ion Implantation on the Surface Features of Inconel 600

1985 ◽  
Vol 43 ◽  
pp. 288-289
Author(s):  
John D. Rubio
Keyword(s):  
Grain Boundary ◽  
Ion Implantation ◽  
Nuclear Power ◽  
Power Plants ◽  
Surface Region ◽  
Selective Dissolution ◽  
Boundary Region ◽  
Near Surface ◽  
Inconel 600 ◽  
Steam Generator Tubing

The degradation of steam generator tubing at nuclear power plants has become an important problem for the electric utilities generating nuclear power. The material used for the tubing, Inconel 600, has been found to be succeptible to intergranular attack (IGA). IGA is the selective dissolution of material along its grain boundaries. The author believes that the sensitivity of Inconel 600 to IGA can be minimized by homogenizing the near-surface region using ion implantation. The collisions between the implanted ions and the atoms in the grain boundary region would displace the atoms and thus effectively smear the grain boundary.To determine the validity of this hypothesis, an Inconel 600 sample was implanted with 100kV N2+ ions to a dose of 1x1016 ions/cm2 and electrolytically etched in a 5% Nital solution at 5V for 20 seconds. The etched sample was then examined using a JEOL JSM25S scanning electron microscope.

Analytical Electron Microscopy of Ion-Implanted Metals

1985 ◽  
Vol 43 ◽  
pp. 282-285
Author(s):  
D.I. Potter ◽  
M. Ahmed ◽  
K. Ruffing
Keyword(s):  
Electron Microscopy ◽  
Ion Implantation ◽  
Friction And Wear ◽  
Analytical Electron Microscopy ◽  
Chemical Compositions ◽  
Surface Chemical ◽  
Near Surface ◽  
The Past ◽  
Analytical Electron ◽  
Property Changes

Ion implantation, used extensively for the past decade in fabricating semiconductor devices, now provides a unique means for altering the near-surface chemical compositions and microstructures of metals. These alterations often significantly improve physical properties that depend on the surface of the material; for example, catalysis, corrosion, oxidation, hardness, friction and wear. Frequently the mechanisms causing these beneficial alterations and property changes remain obscure and much of the current research in the area of ion implantation metallurgy is aimed at identifying such mechanisms. Investigators thus confront two immediate questions: To what extent is the chemical composition changed by implantation? What is the resulting microstructure? These two questions can be investigated very fruitfully with analytical electron microscopy (AEM), as described below.

Sign in / Sign up

Export Citation Format

Share Document