Prediction of Tire-Road Friction from Surface Texture and Tread Rubber Properties

2009 ◽  
pp. 304-304-19 ◽  
Author(s):  
WO Yandell ◽  
P Taneerananon ◽  
V Zankin
Keyword(s):  
Surface Texture ◽  
Road Friction ◽  
Tread Rubber

Truck Tire Operating Temperatures on Flat and Curved Test Surfaces

2005 ◽  
Vol 33 (3) ◽  
pp. 156-178 ◽  
Author(s):  
T. J. LaClair ◽  
C. Zarak
Keyword(s):  
Flat Surface ◽  
Operating Temperature ◽  
Operating Conditions ◽  
Load Pressure ◽  
Truck Tire ◽  
Endurance Testing ◽  
Operating Temperatures ◽  
The Impact ◽  
Tread Rubber ◽  
Cylindrical Test

Abstract Operating temperature is critical to the endurance life of a tire. Fundamental differences between operations of a tire on a flat surface, as experienced in normal highway use, and on a cylindrical test drum may result in a substantially higher tire temperature in the latter case. Nonetheless, cylindrical road wheels are widely used in the industry for tire endurance testing. This paper discusses the important effects of surface curvature on truck tire endurance testing and highlights the impact that curvature has on tire operating temperature. Temperature measurements made during testing on flat and curved surfaces under a range of load, pressure and speed conditions are presented. New tires and re-treaded tires of the same casing construction were evaluated to determine the effect that the tread rubber and pattern have on operating temperatures on the flat and curved test surfaces. The results of this study are used to suggest conditions on a road wheel that provide highway-equivalent operating conditions for truck tire endurance testing.

A Modified Dugoff Tire Model for Combined-slip Forces

2010 ◽  
Vol 38 (3) ◽  
pp. 228-244 ◽  
Author(s):  
Nenggen Ding ◽  
Saied Taheri
Keyword(s):  
Vehicle Dynamics ◽  
Tire Model ◽  
Magic Formula ◽  
Model Based ◽  
Proposed Model ◽  
Road Friction ◽  
On Line ◽  
Double Lane Change ◽  
Tire Forces ◽  
Tire Models

Abstract Easy-to-use tire models for vehicle dynamics have been persistently studied for such applications as control design and model-based on-line estimation. This paper proposes a modified combined-slip tire model based on Dugoff tire. The proposed model takes emphasis on less time consumption for calculation and uses a minimum set of parameters to express tire forces. Modification of Dugoff tire model is made on two aspects: one is taking different tire/road friction coefficients for different magnitudes of slip and the other is employing the concept of friction ellipse. The proposed model is evaluated by comparison with the LuGre tire model. Although there are some discrepancies between the two models, the proposed combined-slip model is generally acceptable due to its simplicity and easiness to use. Extracting parameters from the coefficients of a Magic Formula tire model based on measured tire data, the proposed model is further evaluated by conducting a double lane change maneuver, and simulation results show that the trajectory using the proposed tire model is closer to that using the Magic Formula tire model than Dugoff tire model.

Analysis of the Contact Deformation of Tread Blocks

1992 ◽  
Vol 20 (4) ◽  
pp. 230-253 ◽  
Author(s):  
T. Akasaka ◽  
K. Kabe ◽  
M. Koishi ◽  
M. Kuwashima
Keyword(s):  
Finite Element Method ◽  
Finite Element ◽  
Deformation Behavior ◽  
Contact Deformation ◽  
The Finite Element Method ◽  
The Road ◽  
Loss Of Contact ◽  
Tread Rubber ◽  
Good Agreement ◽  
Rubber Block

Abstract The deformation behavior of a tire in contact with the roadway is complicated, in particular, under the traction and braking conditions. A tread rubber block in contact with the road undergoes compression and shearing forces. These forces may cause the loss of contact at the edges of the block. Theoretical analysis based on the energy method is presented on the contact deformation of a tread rubber block subjected to compressive and shearing forces. Experimental work and numerical calculation by means of the finite element method are conducted to verify the predicted results. Good agreement is obtained among these analytical, numerical, and experimental results.

Tire Treadwear — A Comprehensive Evaluation of the Factors: Generic Type, Aspect Ratio, Tread Pattern, and Tread Composition Part IV: Laboratory Measurement of Mechanical Properties and Mechanical Actions of Tires Relating to Treadwear

1986 ◽  
Vol 14 (4) ◽  
pp. 264-291
Author(s):  
K. L. Oblizajek ◽  
A. G. Veith
Keyword(s):  
Mechanical Properties ◽  
Shear Stress ◽  
Contact Zone ◽  
Flexural Rigidity ◽  
Comprehensive Evaluation ◽  
Shear Stiffness ◽  
Shear Stresses ◽  
Lateral Shear ◽  
Band Bending ◽  
Tread Rubber

Abstract Treadwear is explained by specific mechanical properties and actions of tires. Rubber shear stresses in the contact zone between the tire and the road become large at large slip angles. When normal stresses are insufficient to prevent sliding at the rear of the footprint, wear occurs at a rate that depends on test severity. Two experimental approaches are described to relate treadwear to tire characteristics. The first uses transducers imbedded in a simulated road surface to obtain direct measurements of contact stresses on the loaded, freely-rolling, steered tires. The second approach is developed with the aid of a simple carcass, tread-band, tread-rubber tire model. Various tire structural configurations; characterized by carcass spring rate, edgewise flexural band stiffness, and tread rubber shear stiffness; are simulated and lateral shear stress response in the contact zone is determined. Tires featuring high band stiffness and low carcass stiffness generate lower lateral shear stress levels. Furthermore, coupling of tread-rubber stiffness and band flexural rigidity are important in determining level of shear stresses. Laboratory measurements with the described apparatus produced values of tread-band bending and carcass lateral stiffness for several tire constructions. Good correlation is shown between treadwear and a broad range of tire stiffness and test course severities.

Contact Analysis of Tire Tread Rubber on Flat Surface with Microscopic Roughness3

2006 ◽  
Vol 34 (4) ◽  
pp. 237-255 ◽  
Author(s):  
M. Kuwajima ◽  
M. Koishi ◽  
J. Sugimura
Keyword(s):  
Surface Roughness ◽  
Finite Element ◽  
Sliding Friction ◽  
Tangential Force ◽  
Partial Slip ◽  
Real Contact Area ◽  
Element Analysis ◽  
Real Contact ◽  
Local Slip ◽  
Tread Rubber

Abstract This paper describes experimental and analytical studies of the dependence of tire friction on the surface roughness of pavement. Abrasive papers were adopted as representative of the microscopic surface roughness of pavement surfaces. The rolling∕sliding friction of tire tread rubber against these abrasive papers were measured at low slip velocities. Experimental results indicated that rolling∕sliding frictional characteristics depended on the surface roughness. In order to examine the interfacial phenomena between rubber and the abrasive papers, real contact length, partial slip, and apparent friction coefficient under vertical load and tangential force were analyzed with two-dimensional explicit finite element analysis in which slip-velocity-dependent frictional coefficients were considered. Finite element method results indicated that the sum of real contact area and local partial slip were larger for finer surfaces under the same normal and tangential forces. In addition, the velocity-dependent friction enhanced local slip, where the dependence of local slip on surface roughness was pronounced. It proved that rolling∕sliding friction at low slip ratio was affected by local frictional behavior at microslip regions at asperity contacts.

Improvement of die life with surface texture control and solid lubricant

2012 ◽  
Vol 67 (2) ◽  
pp. 153-157 ◽  
Author(s):  
O. Furukimi ◽  
M. Aramaki ◽  
K. Abe ◽  
H. Fukaura ◽  
N. Yamada
Keyword(s):  
Surface Texture ◽  
Solid Lubricant ◽  
Die Life
Sign in / Sign up

Export Citation Format

Share Document