Mechanism of Cleavage Fracture In Fully Pearlitic 1080 Rail Steel

2009 ◽  
pp. 287-287-16 ◽  
Author(s):  
Y-J Park ◽  
IM Bernstein
Keyword(s):  
Cleavage Fracture ◽  
Rail Steel

Peculiarities of Formation of Residual Stresses in Welded Joints and Stellite Weld Cladding on Rail Steel

2020 ◽  
Vol 11 (3) ◽  
pp. 634-640
Author(s):  
S. Ya. Betsofen ◽  
K. V. Grigorovich ◽  
A. A. Ashmarin ◽  
A. Yu. Abdurashitov ◽  
M. A. Lebedev
Keyword(s):  
Residual Stresses ◽  
Welded Joints ◽  
Rail Steel ◽  
Weld Cladding

Uniaxial Ratcheting and Low-Cycle Fatigue Failure of U75V Rail Steel

2016 ◽  
Vol 853 ◽  
pp. 246-250 ◽  
Author(s):  
Tao Fang ◽  
Qian Hua Kan ◽  
Guo Zheng Kang ◽  
Wen Yi Yan
Keyword(s):  
Fatigue Life ◽  
Strain Amplitude ◽  
Stress Ratio ◽  
Stress Amplitude ◽  
Rail Steel ◽  
Low Cycle Fatigue ◽  
Mean Stress ◽  
Cycle Fatigue ◽  
Ratcheting Strain ◽  
Cyclic Straining

Experiments on U75V rail steel were carried out to investigate the cyclic feature, ratcheting behavior and low-cycle fatigue under both strain- and stress-controlled loadings at room temperature. It was found that U75V rail steel shows strain amplitude dependent cyclic softening feature, i.e., the responded stress amplitude under strain-controlled decreases with the increasing number of cycles and reaches a stable value after about 20th cycle. Ratcheting strain increases with an increasing stress amplitude and mean stress, except for stress ratio, and the ratcheting strain in failure also increases with an increasing stress amplitude, mean stress and stress ratio. The low-cycle fatigue lives under cyclic straining decrease linearly with an increasing strain amplitude, the fatigue lives under cyclic stressing decrease with an increasing mean stress except for zero mean stress, and decrease with an increasing stress amplitude. Ratcheting behavior with a high mean stress reduces fatigue life of rail steel by comparing fatigue lives under stress cycling with those under strain cycling. Research findings are helpful to evaluate fatigue life of U75V rail steel in the railways with passenger and freight traffic.

Bridging microstructure and crystallography with the micromechanics of cleavage fracture in a lamellar pearlitic steel

2021 ◽  
pp. 116988
Author(s):  
Rakesh Kumar Barik ◽  
Abhijit Ghosh ◽  
Md. BasiruddinSk ◽  
Sankalp Biswal ◽  
Amlan Dutta ◽  
...  
Keyword(s):  
Cleavage Fracture ◽  
Pearlitic Steel

scholarly journals A thermodynamic assessment of precipitation, growth, and control of MnS inclusion in U75V heavy rail steel

2021 ◽  
Vol 40 (1) ◽  
pp. 178-192
Author(s):  
Wen-Qiang Ren ◽  
Lu Wang ◽  
Zheng-Liang Xue ◽  
Cheng-Zhi Li ◽  
Hang-Yu Zhu ◽  
...  
Keyword(s):  
Particle Size ◽  
Rail Steel ◽  
Solidification Process ◽  
Segregation Ratio ◽  
Two Phase ◽  
Final Particle ◽  
Solid Liquid ◽  
And Control ◽  
Heavy Rail ◽  
Heavy Rail Steel

Abstract Thermodynamic analysis of the precipitation behavior, growth kinetic, and control mechanism of MnS inclusion in U75V heavy rail steel was conducted in this study. The results showed that solute element S had a much higher segregation ratio than that of Mn, and MnS would only precipitate in the solid–liquid (two-phase) regions at the late stage during the solidification process at the solid fraction of 0.9518. Increasing the cooling rate had no obvious influence on the precipitation time of MnS inclusion; however, its particle size would be decreased greatly. The results also suggested that increasing the concentration of Mn would lead to an earlier precipitation time of MnS, while it had little effect on the final particle size; as to S, it was found that increasing its concentration could not only make the precipitation time earlier but also make the particle size larger. Adding a certain amount of Ti additive could improve the mechanical properties of U75V heavy rail steel due to the formation of TiO x –MnS or MnS–TiS complex inclusions. The precipitation sequences of Ti3O5 → Ti2O3 → TiO2 → TiO → MnS → TiS for Ti treatment were determined based on the thermodynamic calculation.

Austenite Grain Evolution Mechanism of High Carbon Rail Based on Thermal Technology

2020 ◽  
Vol 837 ◽  
pp. 74-80
Author(s):  
Jun Yuan ◽  
Zhen Yu Han ◽  
Yong Deng ◽  
Da Wei Yang
Keyword(s):  
Grain Size ◽  
Tensile Strength ◽  
Rail Steel ◽  
Heating Temperature ◽  
Great Influence ◽  
Stable Operation ◽  
High Carbon ◽  
Austenite Grain Size ◽  
Austenite Grain ◽  
Austenite Grains

In view of the special requirements of rails to ensure the safe and stable operation of Railways in China, the formation characteristics of austenite grains in high carbon rail are revealed through industrial exploration, the process of industrial rail heating and rolling is simulated, innovative experimental research methods such as different heating and heat treatment are carried out on the actual rails in the laboratory. Transfer characteristics of austenite grain size, microstructures and key properties of high carbon rail during the process are also revealed. The results show that the austenite grain size of industrial produced U75V rail is about 9.0 grade. When the holding temperature is increased from 800 C to 1300 C, the austenite grain size of high carbon rail steel decreases, the austenite grain are gradually coarsened, and the tensile strength increases slightly. The tensile strength is affected by the heating temperature. With the increase of heating temperature, the elongation and impact toughness of high carbon rail decrease. The heating temperature of high carbon rail combined with austenite grain size shows that the heating temperature has a great influence on austenite grain size, and has the most obvious influence on the toughness of high carbon rail.

Sign in / Sign up

Export Citation Format

Share Document