A Method for Extrapolating Rupture Ductility

2009 ◽  
pp. 82-82-13
Author(s):  
RM Goldhoff
Keyword(s):  
Rupture Ductility

Creep-Rupture Properties, Resistance to Temper Embrittlement and to Attack by Hydrogen of a 1.4 Percent Mn — 0.25 Percent Mo — 0.03 Percent Cb Steel

1975 ◽  
Vol 97 (3) ◽  
pp. 234-244 ◽  
Author(s):  
T. Wada ◽  
D. L. Sponseller
Keyword(s):  
Carbon Steel ◽  
Rupture Strength ◽  
Temper Embrittlement ◽  
Charpy Impact ◽  
Creep Rupture ◽  
Hydrogen Attack ◽  
Boiler Steel ◽  
Rupture Ductility ◽  
Treated Carbon ◽  
Rupture Properties

A laboratory heat of an improved boiler steel containing 0.13 percent C, 1.36 percent Mn, 0.27 percent Mo, 0.03 percent Cb, and 0.010 percent N was prepared; creep-rupture properties, resistance to temper embrittlement and resistance to hydrogen attack were investigated. The rupture strength was much higher than that of carbon steel and columbium-treated carbon steel, but was somewhat lower than that of two European carbon-0.3 percent Mo boiler steels. Creep-rupture ductility was high. The experimental steel exhibited high toughness, especially in the normalized and stress-relieved condition. No temper embrittlement was induced by step-cooling normalized or normalized and stress-relieved material. Good resistance to hydrogen attack was revealed by tests in a hydrogen autoclave at a pressure of 1000 psi (6.9 N/mm2); the steel retained the original Charpy impact toughness after exposures up to 5000 hr at 900 deg F (480 deg C) and 500 hr at 1000 deg F (540 deg C). No blistering or fissuring were observed.

Correlation between film rupture ductility and PbSCC of Alloy 800

2008 ◽  
Vol 53 (12) ◽  
pp. 4122-4136 ◽  
Author(s):  
B.T. Lu ◽  
J.L. Luo ◽  
Y.C. Lu
Keyword(s):  
Film Rupture ◽  
Rupture Ductility ◽  
Alloy 800

Capped End, Thin-Wall Tube Creep-Rupture Behavior for Type 316 Stainless Steel

1963 ◽  
Vol 85 (1) ◽  
pp. 71-86 ◽  
Author(s):  
G. H. Rowe ◽  
J. R. Stewart ◽  
K. N. Burgess
Keyword(s):  
Biaxial Tension ◽  
Rupture Life ◽  
Creep Rupture ◽  
Uniaxial Tensile ◽  
Thin Wall ◽  
Rupture Ductility ◽  
Statistical Argument ◽  
Stress Ratios ◽  
Rupture Properties ◽  
Rupture Behavior

The creep-rupture behavior of 34 capped end, thin-wall tubular specimens was correlated with results for 54 uniaxial tensile specimens in tests at 1350 F, 1500 F, and 1650 F. Basic tests established isotropy in creep-rupture properties as well as metallurgical stability for the material used in the study. Significant correlations of creep rate, rupture life, and rupture ductility were established for the cases of stress ratios 1/0 and 2/1 in the biaxial tension quadrant. Data from tests at 1500 F were evaluated for a statistical argument. This same material was subsequently utilized in a high temperature structures research program to be reported separately.

Microstructures and Creep Properties of Powder Metallurgy Ti-48Al-2Cr-2Nb + W

2007 ◽  
Author(s):  
H. Saari ◽  
S. Bulmer ◽  
D. Y. Seo ◽  
P. Au
Keyword(s):  
Heat Treatment ◽  
Powder Metallurgy ◽  
Lamellar Microstructure ◽  
Controlled Cooling ◽  
Tial Alloys ◽  
Creep Properties ◽  
Rupture Ductility ◽  
Heat Treated ◽  
Fully Lamellar ◽  
Lamellar Interfaces

The microstructures and creep properties at 760 °C and 276 MPa of three powder metallurgy TiAl alloys (Ti-48Al-2Cr-2Nb, Ti-48Al-2Cr-2Nb+0.5W, and Ti-48Al-2Cr-2Nb+1W (atomic percent)) are presented. The results indicate that the addition of W to the base composition, the use of a solution heat treatment combined with controlled cooling (to generate a fully lamellar microstructure), and the use of an aging heat treatment (to generate precipitate particles at the lamellar interfaces) improve creep properties dramatically. The solution heat treated and aged Ti-48Al-2Cr-2Nb+1W alloy has a time to 0.5% strain of 8.3 hours, a time to 1% strain of 46.4 hours, and a creep life of 412 hours with a rupture ductility of 16.9%.

Creep Rupture Ductility of Creep Strength Enhanced Ferritic Steels

2010 ◽  
Author(s):  
Kazuhiro Kimura ◽  
Kota Sawada ◽  
Hideaki Kushima
Keyword(s):  
Yield Stress ◽  
Creep Strength ◽  
Rupture Strength ◽  
Creep Rupture ◽  
Ferritic Steels ◽  
Creep Rupture Strength ◽  
Stress Regime ◽  
Rupture Ductility ◽  
Strength And Ductility

Creep rupture strength and ductility of Creep Strength Enhanced Ferritic steels of Grades 23, 91, 92 and 122 was investigated with particular emphasis on remarkable drop in the long-term. Large difference in creep rupture strength and ductility was observed on three heats of Grade 23 steels. Remarkable drop of creep rupture strength in the long-term of T91 was comparable to those of Grades 92 and 122. Remarkable drop in creep rupture ductility in a stress regime below 50% of 0.2% offset yield stress was observed on Grade T23 steel, however, that of Grade P23 steel did not indicate any degradation of creep rupture ductility. Higher creep rupture ductility of Grade P23 steel was considered to be caused by its lower creep strength than that of T23 steels. Creep rupture ductility of Grades 92 and 122 steels indicated rapid and drastic decrease with decrease in stress at 50% of 0.2% offset yield stress. Stress dependence of creep rupture ductility of Grades 92 and 122 steels was well described by a ratio of stress to 0.2% offset yield stress, regardless of temperature. On the other hand, large drop in creep rupture ductility of Grade 91 steel was observed only in the very low stress regime at 650°C. Alloying elements including impurities and changes in precipitates may influence on creep rupture ductility, however, remarkable drop in ductility of the steels cannot be explained by chemical composition and precipitates. High ductility in the high stress regime above 50% of 0.2% offset yield stress should be provided by easy plastic deformation, and it has been concluded that a remarkable drop in ductility in the low stress regime is derived from a concentration of creep deformation into a tiny recovered region formed at the vicinity of grain boundary.

Sign in / Sign up

Export Citation Format

Share Document