On the Longitudinal and Transverse Tensile Strength and Work of Fracture of a Continuous Fiber Metal Matrix Composite Subjected to Thermal Exposure

2009 ◽  
pp. 409-409-23
Author(s):  
T Kyono ◽  
IW Hall ◽  
M Taya
Keyword(s):  
Tensile Strength ◽  
Metal Matrix Composite ◽  
Matrix Composite ◽  
Metal Matrix ◽  
Thermal Exposure ◽  
Continuous Fiber ◽  
Transverse Tensile ◽  
Fiber Metal ◽  
Transverse Tensile Strength ◽  
Work Of Fracture

Application of X-Ray Microtomography in Materials Science Illustrated by a Study of a Continuous Fiber Metal Matrix Composite

1990 ◽  
Vol 2 (4) ◽  
pp. 249-258
Author(s):  
J. C. Elliott ◽  
P. Anderson ◽  
G. Davis ◽  
S. D. Dover ◽  
S. R. Stock ◽  
...  
Keyword(s):  
Metal Matrix Composite ◽  
Matrix Composite ◽  
Metal Matrix ◽  
Materials Science ◽  
Continuous Fiber ◽  
X Ray ◽  
Fiber Metal

An appraisal of characteristic mechanical properties and microstructure of friction stir welding for Aluminium 6061 alloy – Silicon Carbide (SiCp) metal matrix composite

2019 ◽  
Vol 13 (4) ◽  
pp. 5804-5817
Author(s):  
Ibrahim Sabry
Keyword(s):  
Tensile Strength ◽  
Ultimate Tensile Strength ◽  
Metal Matrix Composite ◽  
Matrix Composite ◽  
Metal Matrix ◽  
Welded Joint ◽  
Rotation Speed ◽  
Fusion Welding ◽  
Friction Stir ◽  
Al 6061

It is expected that the demand for Metal Matrix Composite (MMCs) will increase in these applications in the aerospace and automotive industries sectors, strengthened AMC has different advantages over monolithic aluminium alloy as it has characteristics between matrix metal and reinforcement particles.  However, adequate joining technique, which is important for structural materials, has not been established for (MMCs) yet. Conventional fusion welding is difficult because of the irregular redistribution or reinforcement particles.  Also, the reaction between reinforcement particles and aluminium matrix as weld defects such as porosity in the fusion zone make fusion welding more difficult. The aim of this work was to show friction stir welding (FSW) feasibility for entering Al 6061/5 to Al 6061/18 wt. % SiCp composites has been produced by using stir casting technique. SiCp is added as reinforcement in to Aluminium alloy (Al 6061) for preparing metal matrix composite. This method is less expensive and very effective. Different rotational speeds,1000 and 1800 rpm and traverse speed 10 mm \ min was examined. Specimen composite plates having thick 10 mm were FS welded successfully. A high-speed steel (HSS) cylindrical instrument with conical pin form was used for FSW. The outcome revealed that the ultimate tensile strength of the welded joint (Al 6061/18 wt. %) was 195 MPa at rotation speed 1800 rpm, the outcome revealed that the ultimate tensile strength of the welded joint (Al 6061/18 wt.%) was 165 MPa at rotation speed 1000 rpm, that was very near to the composite matrix as-cast strength. The research of microstructure showed the reason for increased joint strength and microhardness. The microstructural study showed the reason (4 %) for higher joint strength and microhardness.  due to Significant   of SiCp close to the boundary of the dynamically recrystallized and thermo mechanically affected zone (TMAZ) was observed through rotation speed 1800 rpm. The friction stir welded ultimate tensile strength Decreases as the volume fraction increases of SiCp (18 wt.%).

scholarly journals Experimental Evaluation of Mechanical, Wear and Corrosion properties of AA5083/Graphite Metal Matrix Composite Prepared using Compocasting Process

2019 ◽  
Vol 9 (1) ◽  
pp. 2352-2357
Keyword(s):  
Tensile Strength ◽  
Metal Matrix Composite ◽  
Matrix Composite ◽  
Metal Matrix ◽  
Matrix Material ◽  
Research Work ◽  
Casting Process ◽  
Stir Casting ◽  
Corrosion Properties ◽  
Mechanical And Tribological Properties

In most of the engineering applications such as aviation, defence, marine and automotive requires components with light weight and along with favorable mechanical properties; this demand perhaps satisfied by metal matrix composites (MMCs) of aluminium by virtue of its distinguished achievement. Also MMCs suffer from insufficient process stability, in-adequate economic efficiency and reliability. In the present research work an experiment was developed to synthesize metal matrix composite adopting Aluminium Alloy (AA) 5083 as matrix material reinforced with graphite particulates (6 wt %, 8 wt % & 10 wt %) using two stage in-situ stir casting process. Experiments were implemented to analyze mechanical and tribological properties like ultimate tensile strength, microhardness, wear characteristics and corrosion properties. From the above investigations, it is revealed that microhardness increases with decrease in tensile strength with upsurge in more wt % of reinforcement. Due to the very high self-lubricating property of graphite significant reduction in wear can be observed with deepen in wt % of graphite. Also corrosion rate decreases with more amount of graphite particulate when compared with base matrix material.

Sign in / Sign up

Export Citation Format

Share Document