Micromechanisms of Major/Minor Cycle Fatigue Crack Growth in Inconel 718

2008 ◽  
pp. 383-383-17 ◽  
Author(s):  
S Venkataraman ◽  
T Nicholas ◽  
NE Ashbaugh
Keyword(s):  
Fatigue Crack ◽  
Fatigue Crack Growth ◽  
Crack Growth ◽  
Inconel 718 ◽  
Cycle Fatigue ◽  
Minor Cycle

Reeled CRA Clad/Lined Pipeline Installation: Seastate Optimisation From Fatigue and Fracture Perspective

2018 ◽  
Author(s):  
Daowu Zhou ◽  
T. Sriskandarajah ◽  
Heidi Bowlby ◽  
Ove Skorpen
Keyword(s):  
Fatigue Crack ◽  
Fatigue Crack Growth ◽  
Crack Growth ◽  
Low Cycle Fatigue ◽  
Superposition Method ◽  
Cycle Fatigue ◽  
Limit States ◽  
Simplified Approach ◽  
Fatigue And Fracture ◽  
Girth Welds

The deformation mechanism in reel-lay of corrosive resistance alloy (CRA) clad/lined pipes can facilitate defect tearing and low cycle fatigue crack growth in the girth welds. Pipe-lay after straightening will subject the CRA welds to high cycle fatigue. The permissible seastate for installation will be governed by failure limit states such as local collapse, wrinkling of the liner, fatigue and fracture. By means of a recently completed offshore project in North Sea, this paper discusses seastate optimisation when installing pipelines with CRA girth welds, from a fatigue and fracture perspective. The additional limiting requirement in CRA welds to maintain CRA liner integrity can lead to significant assessment work since all critical welds shall be examined. AUT scanned defect data were utilised to maximise permissible seastates based on fatigue allowance from a fatigue crack growth calculation. An alternative simplified approach to derive the crack growth based on a superposition method is studied. It enables a straightforward real-time prediction of crack growth and has the potential to be used during the offshore campaign to improve the installation flexibility. Post-installation fracture assessment under more critical seastates is examined for CRA partial over-matching welds. A comparison of CDF between conventional ECA procedure and 3D FE is provided.

Mode-II Fatigue Crack Growth Model from Shear-Type Low Cycle Fatigue Properties

2016 ◽  
Vol 853 ◽  
pp. 15-21
Author(s):  
Kai Kai Shi ◽  
Li Xun Cai ◽  
Shuang Qi ◽  
Chen Bao
Keyword(s):  
Fatigue Crack ◽  
Fatigue Crack Growth ◽  
Crack Growth ◽  
Low Cycle Fatigue ◽  
Model Verification ◽  
Fatigue Properties ◽  
Mode Ii ◽  
Cycle Fatigue ◽  
Shear Type ◽  
Crack Growth Model

The inherent law between fatigue behaviors of shear-type representative volume element and mode-II fatigue crack growth is found in the range of cycle plastic zone near the crack tip. Prediction model for mode-II fatigue crack growth rate is then proposed by utilizing shear-type low cycle fatigue properties, plastic strain energy criterion, and effective cycle stress-strain field. Experimental data of two Aluminum alloys, 2024-T351 and 7075-T6, are used for the model verification. Good agreement between experimental and theoretical results is obtained.

scholarly journals Fatigue crack growth behaviour of Inconel 718 – the concept of a damaged zone caused by high temperature hold times

2011 ◽  
Vol 10 ◽  
pp. 2821-2826 ◽  
Author(s):  
David Gustafsson ◽  
Johan Moverare ◽  
Kjell Simonsson ◽  
Sten Johansson ◽  
Magnus Hörnqvist ◽  
...  
Keyword(s):  
Fatigue Crack ◽  
High Temperature ◽  
Fatigue Crack Growth ◽  
Crack Growth ◽  
Inconel 718 ◽  
Growth Behaviour ◽  
Crack Growth Behaviour ◽  
Damaged Zone
Sign in / Sign up

Export Citation Format

Share Document