Effects of Helium/DPA Ratio, Alloy Composition and Cold Work on Microstructural Evolution and Hardening of

2009 ◽  
pp. 831-831-11
Author(s):  
H Kawanishi ◽  
ML Hamilton ◽  
FA Garner
Keyword(s):  
Microstructural Evolution ◽  
Alloy Composition ◽  
Cold Work

Mechanical Alloying of Zr-Nb5%at. Powders: Microstructural Evolution and Hydrogenation Properties

2008 ◽  
Vol 570 ◽  
pp. 59-64 ◽  
Author(s):  
S.A. Loureiro ◽  
Daniel Fruchart ◽  
Sophie Rivoirard ◽  
Dílson S. dos Santos ◽  
L.M. Tavares
Keyword(s):  
Mechanical Alloying ◽  
Crystallite Size ◽  
Microstructural Evolution ◽  
Alloy Composition ◽  
Nuclear Reactors ◽  
Absorption Capacity ◽  
Planetary Mill ◽  
Structural Element ◽  
Fcc Phase ◽  
Nb Addition

Zircaloy is commonly applied as structural element in nuclear reactors owing to the gamma radiation transparency of Zr. One of the research interests in Zr-Nb alloys is related to its behavior in H2O-rich environments due to hydrogen embrittlement. In the present work the microstructural evolution (crystallite size and microhardness), crystallography and hydrogenation behavior (after milling) due to mechanical alloying (MA) are studied for the Zr-Nb5%at and pure Zr. The MA study of Zr and the Zr-Nb system showed that frequency of rotation in a planetary mill and alloy composition play a major role on the evolution of crystallite size and microhardness. Nb addition was found to induce a partial allotropic transformation of the Zr structure (α→ω) during MA. Indeed, for milling experiments with significant Fe contamination the formation of an fcc phase was observed. Further, MA for extended times (over 5 hours) was found to reduce the hydrogen absorption capacity of Zr and the Zr-Nb system studied.

scholarly journals Microstructural Evolution of Mo-Si-B Ternary Alloys through Heat Treatment at 1800°C

2011 ◽  
Vol 278 ◽  
pp. 527-532 ◽  
Author(s):  
Kyosuke Yoshimi ◽  
Soeng Ho Ha ◽  
Kouichi Maruyama ◽  
Rong Tu ◽  
Takashi Goto
Keyword(s):  
Heat Treatment ◽  
Phase Diagram ◽  
Solid Solution ◽  
Microstructural Evolution ◽  
Alloy Composition ◽  
Equilibrium Phase ◽  
Secondary Phase ◽  
Equilibrium Phase Diagram ◽  
The Other ◽  
Ternary Alloys

First of all, the as-cast microstructures of Mo-rich Mo-Si-B ternary alloys were investigated around the triple junction point of the primary Mo solid solution, Mo5SiB2 and Mo2B in this work, based on the liquidus projections of the Mo-Si-B system which have been reported in earlier studies. Subsequently, their microstructural evolution through heat treatment was investigated. Since Mo2B crystallizes out during solidification into a primary or secondary phase even though the alloy composition lies in the triangle of Mo-Mo5SiB2-Mo3Si in the Mo-Si-B equilibrium phase diagram, the as-cast microstructures include the non-equilibrated Mo2B in wide compositional ranges. However, Mo2B was completely decomposed during heat treatment at 1800 °C for 24 h and this contributed to the development of homogeneous, fine microstructures. On the other hand, since Mo2B was not decomposed perfectly during 24 h of 1600 °C heat treatment, as-cast microstructures largely remained. Therefore, it is realized that the heat treatment at 1800 °C is necessary to obtain well-developed microstructures of Mo-Si-B alloys.

Microstructural evolution of Cr–Mn–N austenitic steels during cold work hardening

2006 ◽  
Vol 427 (1-2) ◽  
pp. 246-254 ◽  
Author(s):  
G. Saller ◽  
K. Spiradek-Hahn ◽  
C. Scheu ◽  
H. Clemens
Keyword(s):  
Microstructural Evolution ◽  
Work Hardening ◽  
Cold Work ◽  
Austenitic Steels

Chemical partitioning of elements in Ni-base MC-carbide reinforced eutetic superalloys

1983 ◽  
Vol 41 ◽  
pp. 250-251
Author(s):  
E. F. Koch ◽  
E. L. Hall ◽  
S. W. Yang
Keyword(s):  
Alloy Composition ◽  
Volume Fraction ◽  
Lattice Mismatch ◽  
Turbine Blades ◽  
Eutectic Alloys ◽  
Alloy Matrix ◽  
X Ray ◽  
Gas Turbine Blades ◽  
Analytical Electron ◽  
Analytical Electron Microscope

The plane-front solidified eutectic alloys consisting of aligned tantalum monocarbide fibers in a nickel alloy matrix are currently under consideration for future aircraft and gas turbine blades. The MC fibers provide exceptional strength at high temperatures. In these alloys, the Ni matrix is strengthened by the precipitation of the coherent γ' phase (ordered L12 structure, nominally Ni3Al). The mechanical strength of these materials can be sensitively affected by overall alloy composition, and these strength variations can be due to several factors, including changes in solid solution strength of the γ matrix, changes in they γ' size or morphology, changes in the γ-γ' lattice mismatch or interfacial energy, or changes in the MC morphology, volume fraction, thermal stability, and stoichiometry. In order to differentiate between these various mechanisms, it is necessary to determine the partitioning of elemental additions between the γ,γ', and MC phases. This paper describes the results of such a study using energy dispersive X-ray spectroscopy in the analytical electron microscope.

Influence of Thermo-Mechanical Processing on the Microstructure of Beryllia Dispersed Nickel Alloys

1973 ◽  
Vol 31 ◽  
pp. 184-185
Author(s):  
M.S. Grewal ◽  
S.A. Sastri ◽  
N.J. Grant
Keyword(s):  
High Temperature ◽  
Nickel Alloys ◽  
Thermomechanical Processing ◽  
Cold Work ◽  
High Temperature Strength ◽  
Strengthening Effect ◽  
Mechanical Processing ◽  
Uniform Dispersion ◽  
Oxide Particles ◽  
Nickel Base

Currently there is a great interest in developing nickel base alloys with fine and uniform dispersion of stable oxide particles, for high temperature applications. It is well known that the high temperature strength and stability of an oxide dispersed alloy can be greatly improved by appropriate thermomechanical processing, but the mechanism of this strengthening effect is not well understood. This investigation was undertaken to study the dislocation substructures formed in beryllia dispersed nickel alloys as a function of cold work both with and without intermediate anneals. Two alloys, one Ni-lv/oBeo and other Ni-4.5Mo-30Co-2v/oBeo were investigated. The influence of the substructures produced by Thermo-Mechanical Processing (TMP) on the high temperature creep properties of these alloys was also evaluated.

Influence of Heat Treatments on Microstructures in an Fe-Co-V Alloy

1974 ◽  
Vol 32 ◽  
pp. 512-513
Author(s):  
S. Mahajan ◽  
M. R. Pinnel ◽  
J. E. Bennett
Keyword(s):  
Single Phase ◽  
Alloy Composition ◽  
Supersaturated Solid Solution ◽  
Cell Formation ◽  
Heat Treatments ◽  
Air Cooling ◽  
Iced Brine ◽  
Transmission Electron ◽  
The Matrix ◽  
Bcc Structure

The microstructural changes in an Fe-Co-V alloy (composition by wt.%: 2.97 V, 48.70 Co, 47.34 Fe and balance impurities, such as C, P and Ni) resulting from different heat treatments have been evaluated by optical metallography and transmission electron microscopy. Results indicate that, on air cooling or quenching into iced-brine from the high temperature single phase ϒ (fcc) field, vanadium can be retained in a supersaturated solid solution (α2) which has bcc structure. For the range of cooling rates employed, a portion of the material appears to undergo the γ-α2 transformation massively and the remainder martensitically. Figure 1 shows dislocation topology in a region that may have transformed martensitically. Dislocations are homogeneously distributed throughout the matrix, and there is no evidence for cell formation. The majority of the dislocations project along the projections of <111> vectors onto the (111) plane, implying that they are predominantly of screw character.

NiAl precipitation in Fe-12w/o Cr-5w/o Ni-4w/o Al

1983 ◽  
Vol 41 ◽  
pp. 202-203
Author(s):  
L.E. Murr ◽  
J.S. Dunning ◽  
S. Shankar
Keyword(s):  
Solid Solution ◽  
Stainless Steel ◽  
Stainless Steels ◽  
Alloy Composition ◽  
Chromium Content ◽  
Scale Up ◽  
Optical Metallography ◽  
Property Evaluation ◽  
310 Stainless Steel ◽  
Microstructural Studies

Aluminum additions to conventional 18Cr-8Ni austenitic stainless steel compositions impart excellent resistance to high sulfur environments. However, problems are typically encountered with aluminum additions above about 1% due to embrittlement caused by aluminum in solid solution and the precipitation of NiAl. Consequently, little use has been made of aluminum alloy additions to stainless steels for use in sulfur or H2S environments in the chemical industry, energy conversion or generation, and mineral processing, for example.A research program at the Albany Research Center has concentrated on the development of a wrought alloy composition with as low a chromium content as possible, with the idea of developing a low-chromium substitute for 310 stainless steel (25Cr-20Ni) which is often used in high-sulfur environments. On the basis of workability and microstructural studies involving optical metallography on 100g button ingots soaked at 700°C and air-cooled, a low-alloy composition Fe-12Cr-5Ni-4Al (in wt %) was selected for scale up and property evaluation.

Microstructural Evolution in Reduced TiO2

1981 ◽  
Vol 39 ◽  
pp. 74-75
Author(s):  
W. T. Donlon ◽  
S. Shinozaki ◽  
E. M. Logothetis ◽  
W. Kaizer
Keyword(s):  
Microstructural Evolution ◽  
Point Defects ◽  
Extended Defects ◽  
Small Deviations ◽  
Controlled Atmospheres ◽  
Limited Solubility ◽  
Thin Foils ◽  
Heat Treated ◽  
Porous Polycrystalline ◽  
Crystallographic Shear

Since point defects have a limited solubility in the rutile (TiO2) lattice, small deviations from stoichiometry are known to produce crystallographic shear (CS) planes which accomodate local variations in composition. The material used in this study was porous polycrystalline TiO2 (60% dense), in the form of 3mm. diameter disks, 1mm thick. Samples were mechanically polished, ion-milled by conventional techniques, and initially examined with the use of a Siemens EM102. The electron transparent thin foils were then heat-treated under controlled atmospheres of CO/CO2 and H2 and reexamined in the same manner.The “as-received” material contained mostly TiO2 grains (∼5μm diameter) which had no extended defects. Several grains however, aid exhibit a structure similar to micro-twinned grains observed in reduced rutile. Lattice fringe images (Fig. 1) of these grains reveal that the adjoining layers are not simply twin related variants of a single TinO2n-1 compound. Rather these layers (100 - 250 Å wide) are alternately comprised of stoichiometric TiO2 (rutile) and reduced TiO2 in the form of Ti8O15, with the Ti8O15 layers on either side of the TiO2 being twin related.

Sign in / Sign up

Export Citation Format

Share Document