Two-Parameter Crack-Tip Field Associated with Stable Crack Growth in a Thin Plate: An Experimental Study

2009 ◽  
pp. 48-48-14 ◽  
Author(s):  
MS Dadkhah ◽  
AS Kobayashi
Keyword(s):  
Experimental Study ◽  
Crack Growth ◽  
Thin Plate ◽  
Crack Tip ◽  
Stable Crack Growth ◽  
Crack Tip Field ◽  
Two Parameter

A Fatigue Crack Driving Force Parameter

2008 ◽  
Author(s):  
Ying Xiong ◽  
Zengliang Gao ◽  
Junichi Katsuta ◽  
Takeshi Sakiyama
Keyword(s):  
Fatigue Crack ◽  
Fatigue Crack Growth ◽  
Crack Growth ◽  
Driving Force ◽  
Crack Tip ◽  
Force Model ◽  
Crack Driving Force ◽  
R Ratio ◽  
Two Parameter ◽  
Better Than

Most of the previous parameters that utilized as a crack driving force were established in modifying the parameter Kop in Elber’s effective SIF range (ΔKeff = Kmax–Kop). This paper focuses on the physical meaning of compliance changes caused by plastic deformation at the crack tip, the test was carried out for structural steel under constant amplitude loading, and differences of several parameter ΔKeff in literature are analyzed quantificationally. The effect of actual stress amplitude at the crack tip on fatigue crack growth is investigated, and improved two-parameter driving force model ΔKdrive(=Kmax)n(ΔK^)1−n) has been proposed. Experimental data for several different types of materials taken from literature were used in the analyses. Presented results indicate that the parameter ΔKdrive is equally effective or better than ΔK(=Kmax-Kmin), ΔKeff(=Kmax-Kop) and ΔK*(=(Kmax)α(ΔK+)1−α) in correlating and predicting the R-ratio effects on fatigue crack growth rate.

Constraint Effects on Ductile Crack Growth in SE(T) and SE(B) Specimens With Implications for Assessments of Tearing Resistance

2012 ◽  
Author(s):  
Claudio Ruggieri
Keyword(s):  
Crack Growth ◽  
Crack Tip ◽  
Stable Crack Growth ◽  
Primary Objective ◽  
Crack Growth Resistance ◽  
Tensile Fracture ◽  
Width Ratio ◽  
Cell Parameters ◽  
Crack Tip Constraint ◽  
Fracture Specimens

This work addresses a two-parameter description of crack-tip fields in bend and tensile fracture specimens incorporating the evolution of near-tip stresses following stable crack growth with increased values of the J-integral. The primary objective is to examine the potential coupled effects of geometry and ductile tearing on crack-tip constraint as characterized by the J-Q theory which enables more accurate correlations of crack growth resistance behavior in conventional fracture specimens. Plane-strain, finite element computations including stationary and growth analyses are described for SE(B) and clamped SE(T) specimens having different notch depth to specimen width ratio in the range 0.2 ≤ a/W≤0.5. A computational cell methodology to model Mode I crack extension in ductile materials is utilized to describe the evolution of J with Δa for the fracture specimens. Laboratory testing of an API 5L X70 steel using deeply cracked C(T) specimens is used to measure the crack growth resistance curve for the material and to calibrate the cell parameters. The present results provide additional understanding of the effects of constraint on crack growth which contributes to further evaluation of crack growth resistance properties of pipeline steels using SE (T) and SE(B) specimens.

scholarly journals An Integral Formulation of Two-Parameter Fatigue Crack Growth Model

2018 ◽  
Vol 2018 ◽  
pp. 1-12
Author(s):  
Jianguo Wu ◽  
Shan Jiang ◽  
Wei Zhang ◽  
Zili Wang
Keyword(s):  
Fatigue Crack ◽  
Fatigue Crack Growth ◽  
Crack Propagation ◽  
Crack Growth ◽  
Crack Closure ◽  
Crack Tip ◽  
Integral Form ◽  
Crack Growth Behavior ◽  
Crack Growth Model ◽  
Two Parameter

A two-parameter fatigue crack growth algorithm in integral form is proposed, which can describe the continuous crack growth process over the time period. In this model, the fatigue crack propagation behavior is governed by the temporal crack-tip state including the current applied load and the physical condition due to the previous load sequence. The plasticity-induced crack closure, left by the historical loading sequence, controls the following fatigue crack growth behavior and typically leads to the interaction effects. In the proposed method, a modified crack closure model deriving from the local plastic deformation is employed to account for this load memory effect. In general, this model can simulate the fatigue crack growth under variable amplitude loading. Additionally, this model is established on the physical state of crack tip in the small spatial and temporal scale, and it is used to evaluate the macroscopic crack propagation and fatigue life under irregular tension-tension loading. A special superimposed loading case is discussed to demonstrate the advantage of the proposed model, while the traditional two-parameter approach is not proper functional. Moreover, the typical various load spectra are also employed to validate the method. Good agreements are observed.

EndoFEM Studies in the Mode I Stable Crack Growth of Fatigue Precracked CT Specimen

1999 ◽  
Vol 15 (4) ◽  
pp. 157-167
Author(s):  
C.F. Lee ◽  
K.L. Lee
Keyword(s):  
Crack Growth ◽  
Crack Extension ◽  
Crack Opening ◽  
Crack Tip ◽  
Stable Crack Growth ◽  
Mode I ◽  
Single Fracture ◽  
Fracture Parameter ◽  
Growing Crack ◽  
Original Crack

AbstractIn this paper, the EndoFEM incorporated with a node duplicated and then unloaded crack extension methodology, is employed to produce the CT specimen of A1 2024-T3 with initial fatigue crack and then to simulate its stable crack growth under Mode I condition. Using the experimental P-LLD data, the P-Δa diagram can be estimated by the effective compliance method. This results in a further simulation of crack extending procedures which can obtain the stress-plastic strain distributions of growing crack front and their crack opening profiles, CTOD and CTOA vs. Δa Diagram, COD and COA measured at 5 positions behind the original crack tip vs. Δa diagram. The results mentioned above have excellent agreements with results of related experiments and other computational simulations.In consequence, the paper proposes a single fracture parameter of crack growth which can be casted in the future studies of EndoFEM simulation: (1) Within the crack initiation range whose crack extension rates da/dP has the lowest constant value, the COA measured at 0.5mm behind the original crack tip is takes as 5°; (2) Within the stable crack growth region whose crack extension rates are nonlinearly and monotonically increasing with finite values, the COA measured at 1mm behind the current crack tip is also taken as 5°.

A Comparison of Crack-Tip Field Parameters for Large and Small Fatigue Cracks

1986 ◽  
Vol 108 (3) ◽  
pp. 206-213 ◽  
Author(s):  
K. S. Chan ◽  
J. Lankford ◽  
D. L. Davidson
Keyword(s):  
Crack Growth ◽  
Fatigue Cracks ◽  
Crack Tip ◽  
Integral Approach ◽  
Crack Tip Field ◽  
Cyclic Plastic Zone ◽  
Small Cracks ◽  
Experimental Strain ◽  
Path Dependent ◽  
Crack Growth Rates

A comparison of the elastic-plastic crack-tip fields of large and small fatigue cracks has been made using the ΔJ-integral approach. Using experimental strain and displacement range measurements obtained by means of the stereoimaging technique, the ΔJ-integral has been computed for an aluminum alloy containing either large or small fatigue cracks, by performing line-contour integration along a variety of rectangular paths around the crack tip. These calculations reveal that for both large and small cracks the ΔJ-integral is path-dependent, and that the value of ΔJ increases with decreasing distance from the crack tip. Using an average local ΔJ or one estimated from the CTOD, the enhanced crack growth rates associated with small fatigue cracks can be explained on the basis of the large average ΔJ-integral within the cyclic plastic zone. The effect of crack closure on the computed local ΔJ (or ΔK) and crack growth is discussed.

Sign in / Sign up

Export Citation Format

Share Document