Effect of Heat Treatment and Tantalum on Microstructure and Mechanical Properties of Fe-9Cr-2W-0.25V Steel

2008 ◽  
pp. 376-376-15
Author(s):  
RL Klueh ◽  
N Hashimoto ◽  
MA Sokolov
Keyword(s):  
Mechanical Properties ◽  
Heat Treatment ◽  
Microstructure And Mechanical Properties

Effect of post-heat treatment on microstructure and mechanical properties of laser welded Al-Cu-Mg alloy

2021 ◽  
Vol 64 ◽  
pp. 620-632
Author(s):  
Alexander Malikov ◽  
Anatoly Orishich ◽  
Igor Vitoshkin ◽  
Evgeniy Karpov ◽  
Alexei Ancharov
Keyword(s):  
Mechanical Properties ◽  
Heat Treatment ◽  
Mg Alloy ◽  
Post Heat Treatment ◽  
Microstructure And Mechanical Properties

scholarly journals The Effect of Quenching and Partitioning (Q&P) Heat Treatment on the Microstructure and Mechanical Properties of High Boron Steel

Materials ◽  
2021 ◽  
Vol 14 (6) ◽  
pp. 1556
Author(s):  
Zhao Li ◽  
Run Wu ◽  
Mingwei Li ◽  
Song-Sheng Zeng ◽  
Yu Wang ◽  
...  
Keyword(s):  
Mechanical Properties ◽  
Heat Treatment ◽  
Volume Fraction ◽  
Martensitic Steel ◽  
Boron Steel ◽  
Quenching And Partitioning ◽  
Effect Mechanism ◽  
Microstructure And Mechanical Properties ◽  
High Boron ◽  
Cast Condition

High boron steel is prone to brittle failure due to the boride distributed in it with net-like or fishbone morphology, which limit its applications. The Quenching and Partitioning (Q&P) heat treatment is a promising process to produce martensitic steel with excellent mechanical properties, especially high toughness by increasing the volume fraction of retained austensite (RA) in the martensitic matrix. In this work, the Q&P heat treatment is used to improve the inherent defect of insufficient toughness of high boron steel, and the effect mechanism of this process on microstructure transformation and the change of mechanical properties of the steel has also been investigated. The high boron steel as-casted is composed of martensite, retained austensite (RA) and eutectic borides. A proper quenching and partitioning heat treatment leads to a significant change of the microstructure and mechanical properties of the steel. The net-like and fishbone-like boride is partially broken and spheroidized. The volume fraction of RA increases from 10% in the as-cast condition to 19%, and its morphology also changes from blocky to film-like. Although the macro-hardness has slightly reduced, the toughness is significantly increased up to 7.5 J·cm−2, and the wear resistance is also improved.

Microstructure and Mechanical Properties of Ti-6Al-4V Manufactured by SLM

2015 ◽  
Vol 651-653 ◽  
pp. 677-682 ◽  
Author(s):  
Anatoliy Popovich ◽  
Vadim Sufiiarov ◽  
Evgenii Borisov ◽  
Igor Polozov
Keyword(s):  
Mechanical Properties ◽  
Heat Treatment ◽  
Phase Composition ◽  
Mechanical Behavior ◽  
Ductile Fracture ◽  
Elevated Temperatures ◽  
Initial Material ◽  
Laser Melting ◽  
Microstructure And Mechanical Properties ◽  
Before And After

The article presents results of a study of phase composition and microstructure of initial material and samples obtained by selective laser melting of titanium-based alloy, as well as samples after heat treatment. The effect of heat treatment on microstructure and mechanical properties of specimens was shown. It was studied mechanical behavior of manufactured specimens before and after heat treatment at room and elevated temperatures as well. The heat treatment allows obtaining sufficient mechanical properties of material at room and elevated temperatures such as increase in ductility of material. The fractography of samples showed that they feature ductile fracture with brittle elements.

Sign in / Sign up

Export Citation Format

Share Document