Multiresponse Optimization of Wear Parameters of Steel-Embedded Glass-Epoxy Hybrid Composites Using Taguchi-Grey Method Optimization

2021 ◽  
Vol 10 (1) ◽  
pp. 20200206
Author(s):  
Ganesh R. Chavhan ◽  
Lalit N. Wankhade
Keyword(s):  
Hybrid Composites ◽  
Multiresponse Optimization ◽  
Method Optimization

Morphology and properties of PA6 hybrid composites filled with short carbon fibers and organoclay

2016 ◽  
Vol 2 (3) ◽  
pp. 47-57 ◽  
Author(s):  
S.S. Pesetskii ◽  
S.P. Bogdanovich ◽  
V.V. Dubrovskii ◽  
T.M. Sodyleva ◽  
V.N. Aderikha ◽  
...  
Keyword(s):  
Carbon Fibers ◽  
Hybrid Composites ◽  
Short Carbon

Influence of Multiwall Carbon Nanotube on mechanical and wear properties of Copper – Iron composite

2020 ◽  
Vol 17 (1) ◽  
pp. 7570-7576 ◽  
Author(s):  
H. Sh. Hammood ◽  
S. S. Irhayyim ◽  
A. Y. Awad ◽  
H. A. Abdulhadi
Keyword(s):  
Carbon Nanotubes ◽  
Volume Fraction ◽  
Hybrid Composites ◽  
Hydraulic Press ◽  
Dry Sliding Wear ◽  
Multiwall Carbon Nanotube ◽  
Wear Properties ◽  
Sem Images ◽  
Wear Rates ◽  
Multiwall Carbon

Multiwall Carbon nanotubes (MWCNTs) are frequently attractive due to their novel physical and chemical characteristics, as well as their larger aspect ratio and higher conductivity. Therefore, MWCNTs can allow tremendous possibilities for the improvement of the necessarily unique composite materials system. The present work deals with the fabrication of Cu-Fe/CNTs hybrid composites manufactured by powder metallurgy techniques. Copper powder with 10 vol. % of iron powder and different volume fractions of Multi-Wall Carbon Nanotubes (MWCNTs) were mixed to get hybrid composites. The hybrid composites were fabricated by adding 0.3, 0.6, 0.9, and 1.2 vol.% of MWCNTs to Cu- 10% Fe mixture using a mechanical mixer. The samples were compressed under a load of 700 MPa using a hydraulic press to compact the samples. Sintering was done at 900°C for 2 h at 5ºC/min heating rate. The microscopic structure was studied using a Scanning Electron Microscope (SEM). The effect of CNTs on the mechanical and wear properties, such as micro-hardness, dry sliding wear, density, and porosity were studied in detail. The wear tests were carried out at a fixed time of 20 minutes while the applied loads were varied (5, 10, 15, and 20 N). SEM images revealed that CNTs were uniformly distributed with relative agglomeration within the Cu/Fe matrix. The results showed that the hardness, density, and wear rates decreased while the percentage of porosity increased with increasing the CNT volume fraction. Furthermore, the wear rate for all the CNTs contents increased with the applied load.

Mode II delamination of woven mengkuang fiber/woven silk laminated hybrid composites

2016 ◽  
Vol 58 (4) ◽  
pp. 374-380 ◽  
Author(s):  
Mohd Azwan Husin ◽  
Rozli Zulkifli ◽  
Shahrum Abdullah ◽  
Wan Ramli Wan Daud
Keyword(s):  
Hybrid Composites ◽  
Mode Ii

Mechanical properties of plain woven kenaf/glass fiber reinforced polypropylene hybrid composites

2019 ◽  
Vol 61 (11) ◽  
pp. 1095-1100 ◽  
Author(s):  
Sivakumar Dhar Malingam ◽  
Kathiravan Subramaniam ◽  
Ng Lin Feng ◽  
Siti Hajar Sheikh MD Fadzullah ◽  
Sivaraos Subramonian
Keyword(s):  
Mechanical Properties ◽  
Glass Fiber ◽  
Hybrid Composites ◽  
Fiber Reinforced ◽  
Glass Fiber Reinforced ◽  
Woven Kenaf
Sign in / Sign up

Export Citation Format

Share Document