Laboratory Study to Evaluate the Influence of Reclaimed Asphalt Content on Performance of Recycled Porous Asphalt

2014 ◽  
Vol 43 (6) ◽  
pp. 20140024 ◽  
Author(s):  
F. Frigio ◽  
E. Pasquini ◽  
F. Canestrari
Keyword(s):  
Laboratory Study ◽  
Reclaimed Asphalt ◽  
Porous Asphalt ◽  
Asphalt Content

Influence of mixing procedures on the performance of asphalt mixtures with high reclaimed asphalt content

2019 ◽  
pp. 527-534
Author(s):  
A. Margaritis ◽  
G. Jacobs ◽  
N. Hasheminejad ◽  
J. Blom ◽  
W. Van den bergh
Keyword(s):  
Asphalt Mixtures ◽  
Reclaimed Asphalt ◽  
Asphalt Content

scholarly journals Characteristics of masonry block that utilizes reclaimed asphalt pavement and waste cooking oil as the binder

2019 ◽  
Vol 276 ◽  
pp. 03001
Author(s):  
I Nyoman Arya Thanaya ◽  
I Nyoman Karnata Mataram ◽  
Bayu Setiawan
Keyword(s):  
Compressive Strength ◽  
Asphalt Pavement ◽  
Waste Cooking Oil ◽  
National Standard ◽  
Reclaimed Asphalt Pavement ◽  
Aggregate Gradation ◽  
Reclaimed Asphalt ◽  
Cooking Oil ◽  
Asphalt Content ◽  
Natural Aggregates

The availability of natural aggregate is getting limited, therefore it is required new alternative materials to substitute natural aggregates. Within this experiment reclaimed asphalt pavement (RAP) was used as masonry block with waste cooking oil as the binder. The objective of this experiment was to analyze the RAP asphalt content and aggregate gradation; and the samples characteristics particularly the compressive strength of masonry block minimum of 25 kg/cm2 that meet the Indonesian national standard SNI-03-0348-1989. The asphalt content of the RAP was initially extracted and tested for its aggregate gradation and specific gravity. The RAP was added 20% sand and a certain amount of waste cooking oil and evenly mixed. After that the mixture was compacted in a mould with a Marshall hummer, with compaction cycles for 15, 25, and 35 times where each cycle consists of 3 even blows. The size of the compacted samples were 20x10x8cm. After the samples were taken out from the mould, they were heated in an oven for 12 and 24 hours at 160°C and 200°C. It was found that the minimum waste cooking oil content required 4%. The best compressive strength was found on samples compacted at 15 compaction cycles and heated at 200°C for 24 hours. The un-soaked compressive strength was 80.5 kg/cm2 and 68.67 kg/cm2 for the soaked samples. In general the compressive strength well met the minimum 25 kg/cm2. Other best characteristics was found on samples heated at 160°C for 12 hours, with lowest water absorption of 5.64% and porosity of 4.53%. The Initial Rate of Suction (IRS) was 0,25~0,45 kg/m2.minute.

scholarly journals Evaluation performance of base course mixture containing reclaimed asphalt pavement (RAP)

2018 ◽  
Vol 162 ◽  
pp. 01037 ◽  
Author(s):  
Karim Al helo ◽  
Zaynab Qasim ◽  
Ahmed Majeed
Keyword(s):  
Asphalt Pavement ◽  
Stability Test ◽  
Reclaimed Asphalt Pavement ◽  
Test Results ◽  
Reclaimed Asphalt ◽  
Superpave Gyratory Compactor ◽  
Asphalt Mix ◽  
Asphalt Content ◽  
Base Course ◽  
Durability Performance

This paper presented the effect of addition of Reclaimed Asphalt Pavement (RAP) on performance of mixture with (20%, 30%, 40% and 50%) RAP as proportion of asphalt mix. To compare with virgin mixture marshall flow and stability test was used to evaluated durability performance with (0,1,3, and 7) days immersion and Wheel Truck test was used to evaluated the resist to rutting. The best gradation and optimum asphalt content was selected according to Superpave system. Superpave Gyratory Compactor (SGC) was used to compact mixture with 100-mm diameter. The test results indicated that addition of RAP to mixes showed significant increase on resistance of Durability and Rutting.

scholarly journals Performance of Recycled Porous Hot Mix Asphalt with Gilsonite Additive

2015 ◽  
Vol 2015 ◽  
pp. 1-7 ◽  
Author(s):  
Ludfi Djakfar ◽  
Hendi Bowoputro ◽  
Bangun Prawiro ◽  
Nugraha Tarigan
Keyword(s):  
Hot Mix Asphalt ◽  
Coarse Aggregate ◽  
Recycled Concrete ◽  
Concrete Material ◽  
Porous Asphalt ◽  
Vehicle Load ◽  
Local Roads ◽  
Asphalt Content ◽  
Concrete Materials ◽  
Potential Use

The objective of the study is to evaluate the performance of porous asphalt using waste recycled concrete material and explore the effect of adding Gilsonite to the mixture. As many as 90 Marshall specimens were prepared with varied asphalt content, percentage of Gilsonite as an additive, and proportioned recycled and virgin coarse aggregate. The test includes permeability capability and Marshall characteristics. The results showed that recycled concrete materials seem to have a potential use as aggregate in the hot mix asphalt, particularly on porous hot mix asphalt. Adding Gilsonite at ranges 8–10% improves the Marshall characteristic of the mix, particularly its stability, without decreasing significantly the permeability capability of the mix. The use of recycled materials tends to increase the asphalt content of the mix at about 1 to 2% higher. With stability reaching 750 kg, the hot mix recycled porous asphalt may be suitable for use in the local roads with medium vehicle load.

scholarly journals KARAKTERISTIK CAMPURAN ASPAL PORUS DENGAN SUBSTITUSI GONDORUKEM PADA ASPAL PENETRASI 60/70

2018 ◽  
Vol 1 (3) ◽  
pp. 657-666
Author(s):  
Leni Arlia ◽  
Sofyan M. Saleh ◽  
Renni Anggraini
Keyword(s):  
Asphalt Pavement ◽  
Asphalt Mixture ◽  
Durability Test ◽  
Porous Asphalt ◽  
Gum Rosin ◽  
Asphalt Content ◽  
The Stability ◽  
Rosin Gum ◽  
Almost All ◽  
Pinus Merkusii

Abstract: Porous asphalt has low stability but has high permeability caused by the amount of voids in mixture. For that need to be added other materials to increase the value of the stability on a mixture of pavement. . In this study, the added material used is gum rosin. Gum rosin is obtained by distillation/distillation of the sap from the tree pinus merkusii shaped solid clear yellow to dark yellow. The objecteve of this research is to determine the characteristics of porous asphalt mixture by substituting gum rosin on asphalt penetration 60/70. The specimens preparation of Optimum Asphalt Content (OAC) followed Australian Asphalt pavement Association (AAPA) Method by  parameter of Cantabro Loss (CL), Asphalt Flow Down (AFD), and Voids In Mix (VIM). Open graded  aggregate was applied and variation in bitumen content of 4,5 %; 5%; 5,5%; 6%; and 6,5% excluding gum rosin. Marshall test and calculatio, CL, and AFD were conducted afterward to obtain OAC. Subsequently, the OAC obtained was used to prepare some specimens of the OAC with  variations  ± 0.5 from the OAC and gum rosin variations of 2%, 4%, 6%, and 8%. Permeability and durability test then required specimens at the best optimum asphalt content. Based on this research, the content of the best OAC was 5.56% with gum rosin content of 8% as bitumen substitution material. Besides, almost  all parameter values met the specification of the AAPA (2004). The addition of rosin affect the value of the characteristic of Marshall, CL, and AFD, which increasing the value of stability, VIM, CL, and AFD  along with the increasein percentage of gum rosin. According to the best OAC the value of stability was 554.81 kg, the value of VIM was 18.04%, the value of CL was 20.66%, and the value of AFD was 0.28%.Abstrak: Aspal porus memiliki stabilitas yang rendah namun memiliki permeabilitas tinggi yang disebabkan oleh banyaknya rongga dalam campuran. Untuk itu perlu ditambahkan material lain untuk meningkatkan nilai stabilitas pada campuran perkerasan. Pada penelitian ini bahan tambah yang digunakan adalah gondorukem. Gondorukem merupakan hasil destilasi/penyulingan getah dari pohon pinus merkusii yang berbentuk padat berwarna kuning jernih sampai kuning tua. Tujuan penelitian ini adalah untuk mengetahui karakteristik campuran aspal porus dengan substitusi gondorukem ke dalam aspal penetrasi 60/70. Pembuatan benda uji untuk penentuan kadar aspal optimum (KAO) digunakan metode Australian Asphalt pavement Association (AAPA) dengan parameter nilai cantabro loss (CL), asphalt flow down (AFD), dan voids in mix (VIM). Gradasi agregat yang digunakan adalah gradasi terbuka dengan kadar aspal 4,5 %; 5%; 5,5%; 6%; dan 6,5% tanpa variasi penggunaan gondorukem. Selanjutnya dilakukan pengujian dan perhitungan Marshall, CL, dan AFD untuk mendapatkan KAO. Setelah KAO diperoleh, dibuat benda uji pada KAO dan variasi ± 0,5 dari nilai KAO dengan variasi substitusi gondorukem  sebesar 2%, 4%, 6%, dan 8%. Berdasarkan hasil penelitian KAO terbaik pada 5,56% dengan substitusi 8% gondorukem, dimana semua parameternya telah memenuhi spesifikasi yang disyaratkan AAPA (2004). Penambahan gondorukem berpengaruh terhadap nilai karakteristik Marshall, CL, dan AFD, dimana meningkatkan nilai stabilitas, VIM, CL, dan AFD seiring dengan peningkatan persentase gondorukem. Pada KAO terbaik diperoleh nilai stabilitas sebesar 554,81 kg, nilai VIM sebesar 18,04%, nilai CL sebesar 20,66%, dan nilai AFD sebesar 0,28%.

scholarly journals Mechanical performance assessment of half warm recycled asphalt mixes containing up to 100 % RAP

2017 ◽  
Vol 7 (080) ◽  
pp. 129 ◽  
Author(s):  
J. M. Lizárraga ◽  
A. Jiménez del Barco-Carrión ◽  
A. Ramírez ◽  
P. Díaz ◽  
F. Moreno-Navarro ◽  
...  
Keyword(s):  
Hot Mix Asphalt ◽  
Mechanical Performance ◽  
Asphalt Pavement ◽  
Reclaimed Asphalt Pavement ◽  
Recycled Asphalt ◽  
Stiffness Modulus ◽  
Asphalt Mixes ◽  
Reclaimed Asphalt ◽  
Second Stage ◽  
Asphalt Content

The use of Half Warm Mixes with high Reclaimed Asphalt content (HWMRA) has the potential to generate significant environmental advantages such as the reduction in consumption of natural resources and the emission of gases into the atmosphere. This paper therefore focuses on demonstrating the viability of using these types of mixes in wearing courses. For this purpose, an HWMRA with 70 % and 100 % Reclaimed Asphalt Pavement (RAP) and emulsion were designed in the laboratory. The performance of the mixes was then assessed and compared with that of conventional Hot Mix Asphalt. In a second stage, the mixes were manufactured in-plant, and laid and compacted in an Accelerated Pavement Test track. The cores were then extracted and tested for stiffness modulus and resistance to fatigue. The results from the tests conducted with both the laboratory specimens and the cores showed that the performance of HWMRA is comparable to that of HMA. These findings encourage greater confidence in promoting the use of these types of sustainable asphalt mixes.

scholarly journals The influence of reclaimed asphalt pavement in warm mix asphalt on asphalt concrete binder course with Retona Blend 55

2019 ◽  
Vol 278 ◽  
pp. 01012
Author(s):  
Raudhah ◽  
R. Jachrizal Sumabrata ◽  
Sigit Pranowo Hadiwardoyo
Keyword(s):  
Significant Influence ◽  
Asphalt Concrete ◽  
Asphalt Pavement ◽  
Warm Mix Asphalt ◽  
Public Works ◽  
Reclaimed Asphalt Pavement ◽  
Test Results ◽  
Reclaimed Asphalt ◽  
Marshall Test ◽  
Asphalt Content

Reclaimed asphalt pavement (RAP) comprises removed pavement materials containing high-quality aggregates and asphalt which can be recycled as materials for new pavement construction. It is removed continually for reconstruction, resurfacing, and maintenance purposes, and if not recycled will become waste. This paper determines the influence of using different RAP percentages and asphalt content in warm mix asphalt on the Marshall test results for asphalt concrete binder course (AC-BC) using Retona Blend 55. The percentages of RAP are determined by analyzing the gradation of the existing aggregates in RAP and adding virgin aggregates so that it meets the standard gradation for AC-BC specified by the Ministry of Public Works and Housing. The RAP percentages in the asphalt mixes in this study are 35%, 45%, and 51.55% of total aggregates, while the asphalt contents are 5%, 6%, and 7% of the total mix. To determine the influence of RAP percentage and asphalt content, and to discover if there is any influence from the interaction between these two factors, the analysis is performed using a factorial design. The results of this study show that variation in RAP percentages in the mix has no significant influence on stability, flow, and Marshall quotient, but there is significant influence on void in mineral aggregates (VMA), void in mix (VIM), and void filled with asphalt (VFA). Correlations of 97.5%, 80%, and 95.1%, respectively show that increase in RAP percentage increases VMA and VIM and decreases VFA. The interaction between RAP percentage and asphalt content has no significant influence on Marshall test results.

Sign in / Sign up

Export Citation Format

Share Document