Laboratory-based Unified Permanent Deformation Model for Hot-Mix Asphalt Mixtures

2007 ◽  
Vol 35 (3) ◽  
pp. 13153 ◽  
Author(s):  
M. R. Mitchell ◽  
R. E. Link ◽  
Elie Y. Hajj ◽  
Raj V. Siddharthan ◽  
Peter E. Sebaaly ◽  
...  
Keyword(s):  
Hot Mix Asphalt ◽  
Permanent Deformation ◽  
Asphalt Mixtures ◽  
Deformation Model

Performance of Asphalt Rejuvenators in Hot-Mix Asphalt Containing Recycled Asphalt Shingles

2017 ◽  
Vol 2633 (1) ◽  
pp. 108-116 ◽  
Author(s):  
Max A. Aguirre ◽  
Marwa M. Hassan ◽  
Sharareh Shirzad ◽  
Louay N. Mohammad ◽  
Samuel B. Cooper
Keyword(s):  
Hot Mix Asphalt ◽  
Permanent Deformation ◽  
Fatigue Cracking ◽  
Strain Energy Release ◽  
Asphalt Mixtures ◽  
Bending Test ◽  
Test Results ◽  
Recycled Asphalt ◽  
Recycled Asphalt Shingles ◽  
Asphalt Shingles

The use of recycled asphalt shingles (RAS) in asphalt paving construction represents a sustainable approach to reduce virgin material consumption and negative environmental effects, as well as the cost of asphalt pavement. However, many challenges are yet to be addressed about the use of RAS in paving applications. This study evaluated the effect of the incorporation of postconsumer waste shingles and rejuvenators on the performance of hot-mix asphalt. Four asphalt rejuvenators—one bio-oil and three synthetic oils—were evaluated. A set of laboratory tests was conducted to characterize the performance of asphalt mixtures against permanent deformation and fatigue cracking. The addition of 5% RAS showed an improvement in permanent deformation when compared with a conventional mixture with no RAS. Yet the addition of asphalt rejuvenator products slightly decreased the performance against permanent deformation. On the basis of Hamburg wheel-tracking device test results, the addition of RAS did not adversely affect moisture resistance. Yet semicircular bending test results showed that the asphalt mixtures that contained asphalt rejuvenators had a lower critical strain energy release rate than the minimum threshold value (0.5 kJ/m2), which indicated a greater susceptibility to intermediate-temperature cracking.

scholarly journals Permanent Deformation of Hot Mix Asphalt (HMA) using Dynamic Modulus Simple Performance Test

2019 ◽  
Vol 8 (4) ◽  
pp. 7001-7006
Keyword(s):  
Dynamic Modulus ◽  
Performance Test ◽  
Hot Mix Asphalt ◽  
Permanent Deformation ◽  
Asphalt Mixtures ◽  
Aging Condition ◽  
Modified Bitumen ◽  
Road Users ◽  
Performance Grade ◽  
Different Content

Premature pavement breakdown can be caused by permanent deformation that can contribute to lower riding comfort for road users and an increase in maintenance costs. Dynamic modulus Simple Performance Test (SPT) test are considered to be significant in describing the permanent deformation of hot mix asphalt. In this study, Marshall method of mix design were used in order to prepare four asphalt mixtures comprising different content of Nanopolyacrylate (NP) polymer (0%NP, 2%NP, 4%NP and 6%NP). This study was aimed to evaluate the influence of the NP modified mixture on the permanent deformation. The Performance Grade PG64-22 was obtained by mixing the conventional bitumen (PG64-22) with nanopolyacrylate. Dynamic Shear Rheometer (DSR) at different aging condition were conducted in order to characterise the bitumen performance. While, the Simple Performance Test (SPT) was used to characterize rutting and fatigue on Marshall HMA mixes. Results from the study presented that, NP modified bitumen has a significant impact on the dynamic and rutting resistance. The addition of nanopolyacrylate significantly enhances the rheological properties of asphalt bitumen. The results revealed that 4%NP has high potential to improve rutting and fatigue resistance

scholarly journals Investigating the Effect of Curing and Thermal Equilibrium Time on Rutting Potential of Hot Mix Asphalt

2021 ◽  
Author(s):  
Morteza Ghaffari Jajin ◽  
Niloofar Esmaeili ◽  
Gholam Hossein Hamedi
Keyword(s):  
Service Life ◽  
Thermal Equilibrium ◽  
Hot Mix Asphalt ◽  
Asphalt Pavement ◽  
Permanent Deformation ◽  
Test Chamber ◽  
Asphalt Mixtures ◽  
Curing Time ◽  
Equilibrium Time ◽  
Laboratory Results

Rutting is a common damage of flexible pavements, reducing the service life of asphalt pavement. Due to laboratory limitations, asphalt mixtures are subjected to different curing times (since construction until placement in the test chamber) and thermal equilibrium times (since placement in the test chamber until the beginning of the test) before rutting tests. Neglecting these factors can lead to errors in the laboratory results. Therefore, the present study attempted to investigate the effect of curing times of 1, 2, and 3 days at 25ºC and thermal equilibrium times of 2, 4, and 6 hours on the rutting potential of different hot-mix asphalt (HMA) mixtures. Results of rutting tests showed that the rutting potential of asphalt mixtures decreases by increasing the curing time, while the permanent deformation at the end of loading cycles and rutting potential increase by increasing the thermal equilibrium time. Additionally, the results of statistical analyses revealed that curing time and thermal equilibrium time change the rutting potential of asphalt mixtures.

Effects of Asphalt Foaming on Damage Characteristics of Foamed Warm Mix Asphalt

2021 ◽  
pp. 036119812199782
Author(s):  
Biswajit K. Bairgi ◽  
Md Amanul Hasan ◽  
Rafiqul A. Tarefder
Keyword(s):  
Permanent Deformation ◽  
Warm Mix Asphalt ◽  
Creep Recovery ◽  
Deformation Model ◽  
Contact Method ◽  
Moisture Susceptibility ◽  
Viscoelastic Continuum Damage ◽  
Foamed Asphalt ◽  
Flexural Beam ◽  
Wheel Tracking

In the asphalt foaming process, the foaming water content (FWC) controls the formation and characteristics of water bubbles. These water bubbles are expected to be expelled from the foamed warm mix asphalt (WMA) during mixing and compaction. However, foaming water may not be completely expelled, rather some of the microbubbles may be trapped in the foamed WMA even after compaction. These microbubbles, or undissipated water, can diffuse over time and cause damage to the foamed WMA. To this end, this study has determined the effects of foaming on the fatigue, moisture damage, and permanent deformation characteristics of foamed WMA. Foamed asphalt and mixtures were designed with varying FWCs and they were tested using linear amplitude sweep, multiple stress creep recovery, four-point flexural beam, and Hamburg wheel tracking tests. Primarily, asphalt foaming dynamics were assessed with a laser-based non-contact method. A simplified viscoelastic continuum damage concept and a three-phase permanent deformation model were used for damage evaluation. The study reveals that foaming softens the binder, which results in slightly higher rutting and moisture susceptibility, though an equivalent or slightly improved fatigue characteristic compared with the regular hot mix asphalt.

scholarly journals Performance Evaluation of WMA Containing Re-Refined Acidic Sludge and Amorphous Poly Alpha Olefin (APAO)

2021 ◽  
Vol 13 (6) ◽  
pp. 3315
Author(s):  
Mansour Fakhri ◽  
Danial Arzjani ◽  
Pooyan Ayar ◽  
Maede Mottaghi ◽  
Nima Arzjani
Keyword(s):  
Resilient Modulus ◽  
Permanent Deformation ◽  
Road Construction ◽  
Moisture Damage ◽  
Asphalt Mixtures ◽  
Modified Bitumen ◽  
Alternative Source ◽  
The Road ◽  
Marshall Test ◽  
Alpha Olefin

The use of waste materials has been increasingly conceived as a sustainable alternative to conventional materials in the road construction industry, as concerns have arisen from the uncontrolled exploitation of natural resources in recent years. Re-refined acidic sludge (RAS) obtained from a waste material—acidic sludge—is an alternative source for bitumen. This study’s primary purpose is to evaluate the resistance of warm mix asphalt (WMA) mixtures containing RAS and a polymeric additive against moisture damage and rutting. The modified bitumen studied in this research is a mixture of virgin bitumen 60/70, RAS (10, 20, and 30%), and amorphous poly alpha olefin (APAO) polymer. To this end, Marshall test, moisture susceptibility tests (i.e., tensile strength ratio (TSR), residual Marshall, and Texas boiling water), resilient modulus, and rutting assessment tests (i.e., dynamic creep, Marshall quotient, and Kim) were carried out. The results showed superior values for modified mixtures compared to the control mix considering the Marshall test. Moreover, the probability of a reduction in mixes’ moisture damage was proved by moisture sensitivity tests. The results showed that modified mixtures could improve asphalt mixtures’ permanent deformation resistance and its resilience modulus. Asphalt mixtures containing 20% RAS (substitute for bitumen) showed a better performance in all the experiments among the samples tested.

scholarly journals Effect of Rubberized Bitumen Blending Methods on Permanent Deformation of SMA Rubberized Asphalt Mixtures

2016 ◽  
Vol 2016 ◽  
pp. 1-14 ◽  
Author(s):  
Herda Yati Katman ◽  
Mohd Rasdan Ibrahim ◽  
Mohamed Rehan Karim ◽  
Suhana Koting ◽  
Nuha Salim Mashaan
Keyword(s):  
Creep Behaviour ◽  
Permanent Deformation ◽  
Asphalt Mixtures ◽  
Creep Model ◽  
Materials Testing ◽  
Wet Process ◽  
Test Conditions ◽  
Dynamic Creep ◽  
Different Temperatures ◽  
Stone Mastic Asphalt

This study aims at comparing the permanent deformation of Stone Mastic Asphalt (SMA) rubberized asphalt mixtures produced by the wet process. In this study, rubberized binders were prepared using two different blending methods, namely, continuous blend and terminal blend. To study the creep behaviour of control and rubberized asphalt mixtures, the dynamic creep test was performed using Universal Materials Testing Apparatus (UMATTA) at different temperatures and stress levels. Zhou three-stage creep model was utilized to evaluate the deformation characteristics of the mixtures. In all test conditions, the highest resistance to permanent deformation is showed by the rubberized mixtures produced with continuous blend binders. This study also reveals that the permanent deformation of rubberized mixtures cannot be predicted based on the characteristics of the rubberized binders.

Sign in / Sign up

Export Citation Format

Share Document