An Investigation of Factors Impacting Nitinol Wire Fatigue Life

2009 ◽  
Vol 6 (8) ◽  
pp. 102195 ◽  
Author(s):  
S. Wong ◽  
Z. C. Lin ◽  
A. Tahran ◽  
J. Boylan ◽  
K. Pike ◽  
...  
Keyword(s):  
Fatigue Life ◽  
Nitinol Wire ◽  
Wire Fatigue

An Investigation of Factors Impacting Nitinol Wire Fatigue Life

2010 ◽  
pp. 99-99-9
Author(s):  
S. Wong ◽  
Z. C. Lin ◽  
A. Tahran ◽  
J. Boylan ◽  
K. Pike ◽  
...  
Keyword(s):  
Fatigue Life ◽  
Nitinol Wire ◽  
Wire Fatigue

Fatigue Properties Assessment of Corroded Cable

2009 ◽  
Vol 413-414 ◽  
pp. 757-764 ◽  
Author(s):  
Cheng Ming Lan ◽  
Hui Li
Keyword(s):  
Monte Carlo ◽  
Fatigue Life ◽  
Fatigue Test ◽  
Fatigue Properties ◽  
Test Results ◽  
Original Design ◽  
Parallel Wire ◽  
Parallel Wire Cable ◽  
As Stress ◽  
Wire Fatigue

Based on fatigue test results of corroded wires obtained from dissection of actual parallel wire cables which were used on a certain domestic cable-stayed bridge, the fatigue properties of corroded parallel wire cable are investigated by the method of Monte Carlo simulation in this paper. The results of fatigue life and corrosion degree of corroded wire are presented. Comparisons between the original design information and fatigue test results, it can be seen that corrosions make the fatigue lives of wires decreasing sharply. The fatigue life of individual wire is described by Weibull distribution considered some useful parameters such as, stress range, mean stress, mean static strength and length effects. The effects of percentage of broken wire, cable S-N curve parameter on cable fatigue life are discussed. It can be seen that the cable fatigue lives are controlled by a small fraction of the cable wires with the shortest fatigue lives. Finally, the S-N curves of cable are calculated by Monte Carlo simulations based on the results of individual wire fatigue test, and compared with the results of cable fatigue test.

scholarly journals High compressive pre-strains reduce the bending fatigue life of nitinol wire

2015 ◽  
Vol 44 ◽  
pp. 96-108 ◽  
Author(s):  
Shikha Gupta ◽  
Alan R. Pelton ◽  
Jason D. Weaver ◽  
Xiao-Yan Gong ◽  
Srinidhi Nagaraja
Keyword(s):  
Fatigue Life ◽  
Bending Fatigue ◽  
Nitinol Wire

Tensile Failure of 55-Nitinol Wire

1975 ◽  
Vol 33 ◽  
pp. 46-47
Author(s):  
F. I. Grace
Keyword(s):  
Shape Memory ◽  
Shape Memory Effect ◽  
Memory Effect ◽  
Stoichiometric Composition ◽  
Tensile Failure ◽  
Initial State ◽  
Initial Shape ◽  
Nitinol Wire ◽  
Cscl Type ◽  
Shear Transformation

An interest in NiTi alloys with near stoichiometric composition (55 NiTi) has intensified since they were found to exhibit a unique mechanical shape memory effect at the Naval Ordnance Laboratory some twelve years ago (thus refered to as NITINOL alloys). Since then, the microstructural mechanisms associated with the shape memory effect have been investigated and several interesting engineering applications have appeared.The shape memory effect implies that the alloy deformed from an initial shape will spontaneously return to that initial state upon heating. This behavior is reported to be related to a diffusionless shear transformation which takes place between similar but slightly different CsCl type structures.

Fatigue Life of Superelastic Springs for an Anterior Cruciate Ligament Prosthesis

1995 ◽  
Vol 05 (C8) ◽  
pp. C8-1223-C8-1228
Author(s):  
N. Hagemeister ◽  
L'H. Yahia ◽  
E. Weynant ◽  
T. Lours
Keyword(s):  
Anterior Cruciate Ligament ◽  
Fatigue Life ◽  
Cruciate Ligament ◽  
Anterior Cruciate ◽  
Ligament Prosthesis

Modification of MnS inclusion by tellurium in 38MnVS6 micro-alloyed steel

2020 ◽  
Vol 117 (6) ◽  
pp. 615
Author(s):  
Ping Shen ◽  
Lei Zhou ◽  
Qiankun Yang ◽  
Zhiqi Zeng ◽  
Kenan Ai ◽  
...  
Keyword(s):  
Fatigue Life ◽  
Aspect Ratio ◽  
Strong Influence ◽  
Experimental Results ◽  
Alloyed Steel ◽  
Equivalent Diameter ◽  
Small Aspect Ratio ◽  
Steel Quality ◽  
Eds Analysis ◽  
Micro Alloyed Steel

In 38MnVS6 steel, the morphology of sulfide inclusion has a strong influence on the fatigue life and machinability of the steel. In most cases, the MnS inclusions show strip morphology after rolling, which significantly affects the steel quality. Usually, the MnS inclusion with a spherical morphology is the best morphology for the steel quality. In the present work, tellurium was applied to 38MnVS6 micro-alloyed steel to control the MnS inclusion. Trace tellurium was added into 38MnVS6 steel and the effect of Te on the morphology, composition, size and distribution of MnS inclusions were investigated. Experimental results show that with the increase of Te content, the equivalent diameter and the aspect ratio of inclusion decrease strikingly, and the number of inclusions with small aspect ratio increases. The inclusions are dissociated and spherized. The SEM-EDS analysis indicates that the trace Te mainly dissolves in MnS inclusion. Once the MnS is saturated with Te, MnTe starts to generate and wraps MnS. The critical Te/S value for the formation of MnTe in the 38MnV6 steel is determined to be approximately 0.075. With the increase of Te/S ratio, the aspect ratio of MnS inclusion decreases and gradually reaches a constant level. The Te/S value in the 38MnVS6 steel corresponding to the change of aspect ratio from decreasing to constant ranges from 0.096 to 0.255. This is most likely to be caused by the saturation of Te in the MnS inclusion. After adding Te in the steel, rod-like MnS inclusion is modified to small inclusion and the smaller the MnS inclusion, the lower the aspect ratio.

Sign in / Sign up

Export Citation Format

Share Document