Specification for Stainless Steel Clamps for Securing SDR9 Cross-linked Polyethylene (PEX) Tubing to Metal Insert and Plastic Insert Fittings

2001 ◽  
Author(s):  
Keyword(s):  
Stainless Steel ◽  
Metal Insert

Micro Flash Welding of Super Duplex Stainless Steel with Zr Metallic Glass Insert

2008 ◽  
Vol 580-582 ◽  
pp. 53-56
Author(s):  
Toshio Kuroda ◽  
Kenji Ikeuchi ◽  
Masahiro Shimada ◽  
Akihisa Inoue ◽  
Hisamichi Kimura
Keyword(s):  
Stainless Steel ◽  
Metallic Glass ◽  
Duplex Stainless Steel ◽  
Superplastic Deformation ◽  
Super Duplex Stainless Steel ◽  
Butt Welding ◽  
Metal Insert ◽  
Controlling System ◽  
Metallurgical Bonding ◽  
Flash Welding

Micro flash butt welding of super duplex stainless steel with Zr-based metallic glass insert was carried out using the temperature controlling system. Zr55Cu30Ni5Al10 of Zr-based metallic glass with thickness of 0.05mm and Zr metal with thickness of 0.1mm and 0.5 mm were used as the insert materials, in order to improve weldability. The specimens were mounted on the dies using a Gleeble thermal simulator, and then, flash butt welding was made. After welding, Zrbased metallic glass insert became much thinner than Zr metal insert. The super-cooled liquid in the interface protruded outside due to the superplastic deformation. The formation of the protrusion discharged the oxide films on the butting surfaces and contact surface; resulting in metallurgical bonding through the fresh surfaces. The Fe-Zr metallic compound for Zr-based metallic glass insert was hardly observed. The micro flash butt welding with metallic glass insert was successfully accomplished for super duplex stainless steel.

NiAl precipitation in Fe-12w/o Cr-5w/o Ni-4w/o Al

1983 ◽  
Vol 41 ◽  
pp. 202-203
Author(s):  
L.E. Murr ◽  
J.S. Dunning ◽  
S. Shankar
Keyword(s):  
Solid Solution ◽  
Stainless Steel ◽  
Stainless Steels ◽  
Alloy Composition ◽  
Chromium Content ◽  
Scale Up ◽  
Optical Metallography ◽  
Property Evaluation ◽  
310 Stainless Steel ◽  
Microstructural Studies

Aluminum additions to conventional 18Cr-8Ni austenitic stainless steel compositions impart excellent resistance to high sulfur environments. However, problems are typically encountered with aluminum additions above about 1% due to embrittlement caused by aluminum in solid solution and the precipitation of NiAl. Consequently, little use has been made of aluminum alloy additions to stainless steels for use in sulfur or H2S environments in the chemical industry, energy conversion or generation, and mineral processing, for example.A research program at the Albany Research Center has concentrated on the development of a wrought alloy composition with as low a chromium content as possible, with the idea of developing a low-chromium substitute for 310 stainless steel (25Cr-20Ni) which is often used in high-sulfur environments. On the basis of workability and microstructural studies involving optical metallography on 100g button ingots soaked at 700°C and air-cooled, a low-alloy composition Fe-12Cr-5Ni-4Al (in wt %) was selected for scale up and property evaluation.

Sign in / Sign up

Export Citation Format

Share Document