Specification for Water- or Solvent-Soluble Liquid Adhesives for Automatic Machine Sealing of Top Flaps of Fiberboard Shipping Cases

2016 ◽  
Author(s):  
Keyword(s):  
Automatic Machine ◽  
Soluble Liquid

Characterization of Chemical Impurities in Glutaraldehyde

1975 ◽  
Vol 33 ◽  
pp. 620-621
Author(s):  
B. J. Grenon ◽  
A. J. Tousimis
Keyword(s):  
Glutaric Acid ◽  
Spectroscopic Analysis ◽  
Aldol Condensation ◽  
Condensation Product ◽  
Amorphous Solid ◽  
Water Soluble ◽  
Impurity Component ◽  
Chemical Impurities ◽  
Soluble Liquid

Ever since the introduction of glutaraldehyde as a fixative in electron microscopy of biological specimens, the identification of impurities and consequently their effects on biologic ultrastructure have been under investigation. Several reports postulate that the impurities of glutaraldehyde, used as a fixative, are glutaric acid, glutaraldehyde polymer, acrolein and glutaraldoxime.Analysis of commercially available biological or technical grade glutaraldehyde revealed two major impurity components, none of which has been reported. The first compound is a colorless, water-soluble liquid with a boiling point of 42°C at 16 mm. Utilizing Nuclear Magnetic Resonance (NMR) spectroscopic analysis, this compound has been identified to be — dihydro-2-ethoxy 2H-pyran. This impurity component of the glutaraldehyde biological or technical grades has an UV absorption peak at 235nm. The second compound is a white amorphous solid which is insoluble in water and has a melting point of 80-82°C. Initial chemical analysis indicates that this compound is an aldol condensation product(s) of glutaraldehyde.

Automatic Tread Gaging Machine

1979 ◽  
Vol 7 (1) ◽  
pp. 31-39
Author(s):  
G. S. Ludwig ◽  
F. C. Brenner
Keyword(s):  
Experimental Tests ◽  
Automatic Machine ◽  
Wear Rates ◽  
Handling Device ◽  
Straight Line ◽  
Component Systems ◽  
Before And After ◽  
Good Repeatability ◽  
The Difference ◽  
Straight Lines

Abstract An automatic tread gaging machine has been developed. It consists of three component systems: (1) a laser gaging head, (2) a tire handling device, and (3) a computer that controls the movement of the tire handling machine, processes the data, and computes the least-squares straight line from which a wear rate may be estimated. Experimental tests show that the machine has good repeatability. In comparisons with measurements obtained by a hand gage, the automatic machine gives smaller average groove depths. The difference before and after a period of wear for both methods of measurement are the same. Wear rates estimated from the slopes of straight lines fitted to both sets of data are not significantly different.

AISI 1141

Alloy Digest ◽  
1983 ◽  
Vol 32 (3) ◽  
Keyword(s):  
Carbon Steel ◽  
Transverse Direction ◽  
Longitudinal Direction ◽  
Heat Treating ◽  
Automatic Machine ◽  
Steel Mills ◽  
Light Duty ◽  
High Production ◽  
Ball Joints ◽  
Machining Characteristics

Abstract AISI 1141 is a resulfurized carbon steel containing nominally 1.50% manganese and 0.08-0.13% sulfur to give it free-machining characteristics. It has relatively low hardenability. Its ductility and toughness are fairly good in the longitudinal direction but tend to be low in the transverse direction. It is highly recommended for high-production automatic-machine products. Among its many uses are screws, bolts, ball joints, spindles and light-duty gears. This datasheet provides information on composition, physical properties, hardness, and tensile properties. It also includes information on forming, heat treating, machining, joining, and surface treatment. Filing Code: CS-93. Producer or source: Carbon steel mills.

Sign in / Sign up

Export Citation Format

Share Document