Mechanical properties and fiber characteristics of glass fiber/carbon fiber reinforced polyethylene terephthalate hybrid composites fabricated by direct fiber feeding injection molding

2018 ◽  
Vol 38 (6) ◽  
pp. 513-523 ◽  
Author(s):  
Wiranphat Thodsaratpreeyakul ◽  
Putinun Uawongsuwan ◽  
Akio Kataoka ◽  
Takanori Negoro ◽  
Hiroyuki Hamada
Keyword(s):  
Mechanical Properties ◽  
Carbon Fiber ◽  
Injection Molding ◽  
Glass Fiber ◽  
Polyethylene Terephthalate ◽  
Fiber Orientation ◽  
Mechanical Performance ◽  
Hybrid Composites ◽  
Fiber Distribution ◽  
Volume Fractions

Abstract Improving the applicability of polyethylene terephthalate (PET) by carbon fiber/glass fiber reinforcement is of great interest. Glass fiber (GF)/carbon fiber (CF)/PET hybrid composites were fabricated by direct fiber feeding injection molding (DFFIM) process. The aim of DFFIM is to obtain longer fibers in composites in order to improve their mechanical properties. In this study, the mechanical properties of GF/PET composites fabricated by conventional injection molding and hybrid GF/CF/PET composites fabricated by DFFIM process were investigated. The influence of GF and CF volume fractions on fiber distribution, fiber orientation, and fiber length is discussed. Fiber distribution status was quantitatively measured by the fiber distribution index. Fiber agglomeration problem was observed by scanning electron microscopy. The results indicate that incorporating CF in GF/CF/PET hybrid composites by the DFFIM process greatly enhances mechanical performance even when only a small amount of CF is added. Too high GF content leads to less effective CF hybridization because it causes poor fiber distribution and poor fiber orientation and intensifies fiber attrition. The ideal volume fractions of GF and CF for fabricating GF/CF/PET hybrid composites by using DFFIM are provided.

Mechanical Properties of GF/CF Hybrid ABS Composite by DFFIM

2017 ◽  
Vol 728 ◽  
pp. 240-245 ◽  
Author(s):  
Yuuki Hisakura ◽  
Keinichi Kitahara ◽  
Makoto Sugihara ◽  
Akihiko Imajo ◽  
Hiroyuki Hamada
Keyword(s):  
Mechanical Properties ◽  
Carbon Fiber ◽  
Injection Molding ◽  
Glass Fiber ◽  
Impact Test ◽  
Hybrid Composites ◽  
Fabrication Technique ◽  
Impact Properties ◽  
Izod Impact ◽  
Mechanical Performances

The direct fiber feeding injection molding (DFFIM) process is the new fabrication technique. This technique is able to eliminate the compounding process. In this study, the composite consisting of glass fiber/carbon fiber/ABS (GF/CF/ABS) were fabricated. Tensile, bending and Izod impact test were conducted to compare mechanical properties between glass fiber and glass fiber/carbon fiber hybrid composites. The additional of carbon fiber improved tensile, bending and impact properties of the hybrid composites. SEM photographs indicated that carbon fiber tended to agglomerate during DFFIM process. It can be noted that the low content of carbon fiber was suitable for enhanced mechanical performances of GF/CF/ABS hybrid composites.

scholarly journals Effect of Submicron Glass Fiber Modification on Mechanical Properties of Short Carbon Fiber Reinforced Polymer Composite with Different Fiber Length

2020 ◽  
Vol 4 (1) ◽  
pp. 5
Author(s):  
Nhan Thi Thanh Nguyen ◽  
Obunai Kiyotaka ◽  
Okubo Kazuya ◽  
Fujii Toru ◽  
Shibata Ou ◽  
...  
Keyword(s):  
Mechanical Properties ◽  
Carbon Fiber ◽  
Glass Fiber ◽  
Fiber Length ◽  
Bending Strength ◽  
Mechanical Performance ◽  
Volume Fraction ◽  
Fiber Concentration ◽  
Static Tests ◽  
The Impact

In this research, three kinds of carbon fiber (CF) with lengths of 1, 3, and 25 mm were prepared for processing composite. The effect of submicron glass fiber addition (sGF) on mechanical properties of composites with different CF lengths was investigated and compared throughout static tests (i.e., bending, tensile, and impact), as well as the tension-tension fatigue test. The strengths of composites increased with the increase of CF length. However, there was a significant improvement when the fiber length changed from 1 to 3 mm. The mechanical performance of 3 and 25 mm was almost the same when having an equal volume fraction, except for the impact resistance. Comparing the static strengths when varying the sGF content, an improvement of bending strength was confirmed when sGF was added into 1 mm composite due to toughened matrix. However, when longer fiber was used and fiber concentration was high, mechanical properties of composite were almost dependent on the CF. Therefore, the modification effect of matrix due to sGF addition disappeared. In contrast to the static strengths, the fatigue durability of composites increased proportionally to the content of glass fiber in the matrix, regardless to CF length.

Mechanical performance of intraply and inter-intraply hybrid composites based on e-glass and polypropylene unidirectional fibers

2016 ◽  
Vol 51 (3) ◽  
pp. 381-394 ◽  
Author(s):  
MA Attia ◽  
MA Abd El-baky ◽  
AE Alshorbagy
Keyword(s):  
Mechanical Properties ◽  
Glass Fiber ◽  
Hybrid Composite ◽  
Mechanical Performance ◽  
Hybrid Composites ◽  
Stacking Sequence ◽  
Unidirectional Fibers ◽  
Interlaminar Shear ◽  
Hybrid Configuration ◽  
Intraply Hybrid Composite

The aims of this study are to design, fabricate and investigate the mechanical properties of new hybrid composite laminates made from polypropylene-glass unidirectional fibers and epoxy matrix. Specimens were fabricated following the hand lay-up technique in intraply and inter-intraply configurations. Results are presented regarding the tensile, flexural, in-plane shear and interlaminar shear behaviors of fabricated composites with particular consideration of the effects of the plies stacking sequence and hybrid configuration. The experimental results reveal that the mechanical properties of polypropylene/epoxy composite can be effectively improved by the incorporation of glass fiber through the formation of either intraply or inter-intraply hybrid composites. With a proper choice of the hybrid configuration and the plies stacking sequence, the fabricated hybrid composites achieved property profiles close to those of homogeneous glass reinforced laminate in terms of specific properties. Resistance of the intraply hybrid composite to tensile and flexural loadings is higher than inter-intraply hybrid composites. On the other hand, the highest in-plane and interlaminar shear strengths are associated with the inter-intraply hybrid composite with glass fiber core. Additionally, an analytical analysis was also introduced to provide a good correlation with the experimental data, which give an insight on the ideal plies stacking sequence to achieve the required properties.

scholarly journals Computational Modeling of Hybrid Carbon Fiber/Epoxy Composites Reinforced with Functionalized and Non-Functionalized Graphene Nanoplatelets

Nanomaterials ◽  
2021 ◽  
Vol 11 (11) ◽  
pp. 2919
Author(s):  
Hashim Al Mahmud ◽  
Matthew S. Radue ◽  
William A. Pisani ◽  
Gregory M. Odegard
Keyword(s):  
Mechanical Properties ◽  
Graphene Oxide ◽  
Carbon Fiber ◽  
Hybrid Composites ◽  
Graphene Nanoplatelets ◽  
Functionalized Graphene ◽  
Graphene Nanoplatelet ◽  
Functionalized Graphene Oxide ◽  
Volume Fractions ◽  
Aspect Ratios

The mechanical properties of aerospace carbon fiber/graphene nanoplatelet/epoxy hybrid composites reinforced with pristine graphene nanoplatelets (GNP), highly concentrated graphene oxide (GO), and Functionalized Graphene Oxide (FGO) are investigated in this study. By utilizing molecular dynamics data from the literature, the bulk-level mechanical properties of hybrid composites are predicted using micromechanics techniques for different graphene nanoplatelet types, nanoplatelet volume fractions, nanoplatelet aspect ratios, carbon fiber volume fractions, and laminate lay-ups (unidirectional, cross-ply, and angle-ply). For the unidirectional hybrid composites, the results indicate that the shear and transverse properties are significantly affected by the nanoplatelet type, loading and aspect ratio. For the cross-ply and angle ply hybrid laminates, the effect of the nanoplate’s parameters on the mechanical properties is minimal when using volume fractions and aspect ratios that are typically used experimentally. The results of this study can be used in the design of hybrid composites to tailor specific laminate properties by adjusting nanoplatelet parameters.

Mechanical properties of plain woven kenaf/glass fiber reinforced polypropylene hybrid composites

2019 ◽  
Vol 61 (11) ◽  
pp. 1095-1100 ◽  
Author(s):  
Sivakumar Dhar Malingam ◽  
Kathiravan Subramaniam ◽  
Ng Lin Feng ◽  
Siti Hajar Sheikh MD Fadzullah ◽  
Sivaraos Subramonian
Keyword(s):  
Mechanical Properties ◽  
Glass Fiber ◽  
Hybrid Composites ◽  
Fiber Reinforced ◽  
Glass Fiber Reinforced ◽  
Woven Kenaf

Experimental investigation of the mechanical behavior of glass fiber/high fluidity polyamide-based composites for automotive market

2021 ◽  
pp. 073168442110140
Author(s):  
Hossein Ramezani-Dana ◽  
Moussa Gomina ◽  
Joël Bréard ◽  
Gilles Orange
Keyword(s):  
Mechanical Properties ◽  
Glass Fiber ◽  
Mechanical Performance ◽  
Physical And Mechanical Properties ◽  
Ultimate Strain ◽  
Uniaxial Tensile ◽  
Compression Tests ◽  
Automotive Market ◽  
Glass Fiber Reinforced ◽  
Glass Fiber Reinforcement

In this work, we examine the relationships between the microstructure and the mechanical properties of glass fiber–reinforced polyamide 6,6 composite materials ( V f = 54%). These materials made by thermocompression incorporate different grades of high fluidity polyamide-based polymers and two types of quasi-UD glass fiber reinforcement. One is a classic commercial fabric, while the other specially designed and manufactured incorporates weaker tex glass yarns (the spacer) to increase the planar permeability of the preform. The effects of the viscosity of the polymers and their composition on the wettability of the reinforcements were analyzed by scanning electron microscopy observations of the microstructure. The respective influences of the polymers and the spacer on the mechanical performance were determined by uniaxial tensile and compression tests in the directions parallel and transverse to the warp yarns. Not only does the spacer enhance permeability but it also improves physical and mechanical properties: tensile longitudinal Young’s modulus increased from 38.2 GPa to 42.9 GPa (13% growth), tensile strength increased from 618.9 MPa to 697 MPa (3% growth), and decrease in ultimate strain from 1.8% to 1.7% (5% reduction). The correlation of these results with the damage observed post mortem confirms those acquired from analyses of the microstructure of composites and the rheological behaviors of polymers.

Sign in / Sign up

Export Citation Format

Share Document