scholarly journals Analysis of spatial thermal field in a magnetic bearing

Open Physics ◽  
2018 ◽  
Vol 16 (1) ◽  
pp. 52-56
Author(s):  
Dawid Wajnert ◽  
Bronisław Tomczuk
Keyword(s):  
Temperature Field ◽  
Mathematical Models ◽  
Computer Simulations ◽  
Thermal Field ◽  
Three Dimensional ◽  
Magnetic Bearing ◽  
Field Analysis ◽  
Two Dimensional ◽  
Temperature Distributions ◽  
Dimensional Simulation

AbstractThis paper presents two mathematical models for temperature field analysis in a new hybrid magnetic bearing. Temperature distributions have been calculated using a three dimensional simulation and a two dimensional one. A physical model for temperature testing in the magnetic bearing has been developed. Some results obtained from computer simulations were compared with measurements.

The Effect of Bench Arrangements on the Natural Ventilation of a Multispan Greenhouse

2013 ◽  
Author(s):  
Sunita Kruger ◽  
Leon Pretorius
Keyword(s):  
Fluid Dynamics ◽  
Natural Ventilation ◽  
Three Dimensional ◽  
Two Dimensional ◽  
Low Velocity ◽  
Lower Velocity ◽  
Cfd Models ◽  
Temperature Distributions ◽  
Computational Fluid Dynamics Cfd ◽  
Plant Level

In this paper, the influence of various bench arrangements on the microclimate inside a two-span greenhouse is numerically investigated using three-dimensional Computational Fluid Dynamics (CFD) models. Longitudinal and peninsular arrangements are investigated for both leeward and windward opened roof ventilators. The velocity and temperature distributions at plant level (1m) were of particular interest. The research in this paper is an extension of two-dimensional work conducted previously [1]. Results indicate that bench layouts inside the greenhouse have a significant effect on the microclimate at plant level. It was found that vent opening direction (leeward or windward) influences the velocity and temperature distributions at plant level noticeably. Results also indicated that in general, the leeward facing greenhouses containing either type of bench arrangement exhibit a lower velocity distribution at plant level compared to windward facing greenhouses. The latter type of greenhouses has regions with relatively high velocities at plant level which could cause some concern. The scalar plots indicate that more stagnant areas of low velocity appear for the leeward facing greenhouses. The windward facing greenhouses also display more heterogeneity at plant level as far as temperature is concerned.

Direct simulation of evolution and control of three-dimensional instabilities in attachment-line boundary layers

1995 ◽  
Vol 291 ◽  
pp. 369-392 ◽  
Author(s):  
Ronald D. Joslin
Keyword(s):  
Boundary Layer ◽  
Stokes Equations ◽  
Three Dimensional ◽  
Plate Boundary ◽  
Navier Stokes ◽  
Two Dimensional ◽  
Computationally Efficient ◽  
Simulation Results ◽  
Dimensional Simulation ◽  
Attachment Line

The spatial evolution of three-dimensional disturbances in an attachment-line boundary layer is computed by direct numerical simulation of the unsteady, incompressible Navier–Stokes equations. Disturbances are introduced into the boundary layer by harmonic sources that involve unsteady suction and blowing through the wall. Various harmonic-source generators are implemented on or near the attachment line, and the disturbance evolutions are compared. Previous two-dimensional simulation results and nonparallel theory are compared with the present results. The three-dimensional simulation results for disturbances with quasi-two-dimensional features indicate growth rates of only a few percent larger than pure two-dimensional results; however, the results are close enough to enable the use of the more computationally efficient, two-dimensional approach. However, true three-dimensional disturbances are more likely in practice and are more stable than two-dimensional disturbances. Disturbances generated off (but near) the attachment line spread both away from and toward the attachment line as they evolve. The evolution pattern is comparable to wave packets in flat-plate boundary-layer flows. Suction stabilizes the quasi-two-dimensional attachment-line instabilities, and blowing destabilizes these instabilities; these results qualitatively agree with the theory. Furthermore, suction stabilizes the disturbances that develop off the attachment line. Clearly, disturbances that are generated near the attachment line can supply energy to attachment-line instabilities, but suction can be used to stabilize these instabilities.

Three-dimensional simulation of thermal field for a high-speed turbine generator

2013 ◽  
Vol 84 (9) ◽  
pp. 487-491
Author(s):  
V. N. Antipov ◽  
I. Yu. Kruchinina ◽  
A. D. Grozov
Keyword(s):  
High Speed ◽  
Thermal Field ◽  
Three Dimensional ◽  
Turbine Generator ◽  
Dimensional Simulation

Three-Dimensional Dynamic Modeling of the Human Knee to Include Tibio-Femoral and Patello-Femoral Joints

2001 ◽  
Author(s):  
Dumitru Caruntu ◽  
Mohamed Samir Hefzy
Keyword(s):  
Knee Joint ◽  
Mathematical Models ◽  
Dynamic Modeling ◽  
Three Dimensional ◽  
Two Dimensional ◽  
Dimensional Model ◽  
Human Knee ◽  
Two Dimensional Model ◽  
Rigid Contact ◽  
Locomotor Activities

Abstract Most of the anatomical mathematical models that have been developed to study the human knee are either for the tibio-femoral joint (TFJ) or patello-femoral joint (PFJ). Also, most of these models are static or quasistatic, and therefore do not predict the effects of dynamic inertial loads, which occur in many locomotor activities. The only dynamic anatomical model that includes both joints is a two-dimensional model by Tumer and Engin [1]. The model by Abdel-Rahman and Hefzy [2] is the only three dimensional dynamic model for the knee joint available in the literature; yet, it includes only the TFJ and allows only for rigid contact.

scholarly journals On the correctness of mathematical models of time-of-flight cathodoluminescence of direct-gap semiconductors

2019 ◽  
Vol 30 ◽  
pp. 07014
Author(s):  
Mikhail A. Stepovich ◽  
Dmitry V. Turtin ◽  
Elena V. Seregina ◽  
Veronika V. Kalmanovich
Keyword(s):  
Electron Beam ◽  
Gallium Nitride ◽  
Initial Data ◽  
Mathematical Models ◽  
Single Crystal ◽  
Three Dimensional ◽  
Time Of Flight ◽  
Semiconductor Material ◽  
Two Dimensional ◽  
Cathodoluminescence Intensity

Two-dimensional and three-dimensional mathematical models of diffusion and cathodoluminescence of excitons in single-crystal gallium nitride excited by a pulsating sharply focused electron beam in a homogeneous semiconductor material are compared. The correctness of these models has been carried out, estimates have been obtained to evaluate the effect of errors in the initial data on the distribution of the diffusing excitons and the cathodoluminescence intensity.

A THREE-DIMENSIONAL SIMULATION OF BRITTLE SOLID FRACTURE

1996 ◽  
Vol 07 (05) ◽  
pp. 717-729 ◽  
Author(s):  
ALEXANDER V. POTAPOV ◽  
CHARLES S. CAMPBELL
Keyword(s):  
Three Dimensional ◽  
Three Dimensions ◽  
Size Distributions ◽  
Two Dimensional ◽  
Brittle Solid ◽  
Space Filling ◽  
Comparison With Experiment ◽  
Linear Dimensions ◽  
Dimensional Simulation ◽  
Simulated Material

This paper describes an extension into three dimensions of an existing two-dimensional technique for simulating brittle solid fracture. The fracture occurs on a simulated solid created by "gluing" together space-filling polyhedral elements with compliant interelement joints. Such a material can be shown to have well-defined elastic properties. However, the "glue" can only support a specified tensile stress and breaks when that stress is exceeded. In this manner, a crack can propagate across the simulated material. A comparison with experiment shows that the simulation can accurately reproduce the size distributions for all fragments with linear dimensions greater than three element sizes.

Impact of Cavity on Sunroof Buffeting: A Two Dimensional CFD Study

2004 ◽  
Author(s):  
Chang-Fa An ◽  
Seyed Mehdi Alaie ◽  
Michael S. Scislowicz
Keyword(s):  
Fluid Dynamics ◽  
Wind Tunnel ◽  
Three Dimensional ◽  
Leading Edge ◽  
Two Dimensional ◽  
Deep Insight ◽  
Simulation Results ◽  
Dimensional Simulation ◽  
The Impact ◽  
Insight Into

Driven by fluid dynamics principles, the concept for buffeting reduction, a cavity installed at the leading edge of the sunroof opening, is analyzed. The cavity provides a room to hold the vortex, shed from upstream, and prevents the vortex from escaping and from directly intruding into the cabin. The concept has been verified by means of a two dimensional simulation for a production SUV using the CFD software — FLUENT. The simulation results show that the impact of the cavity is crucial to reduce buffeting. It is shown that the buffeting level may be reduced by 3 dB by adding a cavity to the sunroof configuration. Therefore, the cavity could be considered as a means of buffeting reduction, in addition to the three currently-known concepts: wind deflector, sunroof glass comfort position and cabin venting. Thorough understanding of the buffeting mechanism helps explain why and how the cavity works to reduce buffeting. Investigation of the buffeting-related physics provides a deep insight into the flow nature and, therefore, a useful hint to geometry modification for buffeting reduction. The buffeting level may be further reduced by about 4 dB or more by cutting the corners of the sunroof opening into smooth ramps, guided by ideas coming from careful examining the physics of flow. More work including three dimensional simulation and wind tunnel experiment should follow in order to develop more confidence in the functionality of the cavity to hopefully promote this idea to the level that it can be utilized in a feasible way to address sunroof buffeting.

scholarly journals CFD Analysis of Nozzle Exit Position Effect in Ejector Gas Removal System in Geothermal Power Plant

2015 ◽  
Vol 3 (1) ◽  
Author(s):  
Setyo Nugroho ◽  
Ciptananda Citrahardhani
Keyword(s):  
Reverse Flow ◽  
Position Effect ◽  
Computational Simulation ◽  
Three Dimensional ◽  
Operating Conditions ◽  
Two Dimensional ◽  
Exit Nozzle ◽  
Gas Removal ◽  
Nozzle Position ◽  
Dimensional Simulation

The single stage ejector is used to extract the Non CondensableGas (NCG) in the condenser using the working principle of the Venturi tube. Three dimensional computational simulation of the ejector according to the operating conditions was conducted to determine the flow in the ejector. Motive steam entering through the convergent – divergent nozzle with increasing flow velocity so that the low pressure exist around the nozzle. Comparison is done also in a two dimensional simulation to know the differences occurring phenomena and flow inside ejector. Different simulation results obtained between two dimensional and three dimensional simulation. Reverse flow which occurs in the mixing chamber made the static pressure in the area has increased dramatically. Then the variation performed on Exit Nozzle Position (NXP) to determine the changes of the flow of the NCG and the vacuum level of the ejector.Keywords: Ejector, NCG, CFD, Compressible flow.

A Comparative Study Between Two-Dimensional and Three-Dimensional Simulation Results of Melting Inside a Container

2020 ◽  
Author(s):  
Nan Hu ◽  
Li-Wu Fan
Keyword(s):  
Velocity Profile ◽  
Heating Temperature ◽  
Three Dimensional ◽  
Detailed Comparison ◽  
Melting Rate ◽  
Two Dimensional ◽  
End Effects ◽  
Wall Superheat ◽  
Simulation Results ◽  
Dimensional Simulation

Abstract Bother two-dimensional (2D) and three-dimensional (3D) simulations on two example melting problems, i.e., melting in a differentially-heated rectangular cavity and constrained melting in a horizontal cylindrical capsule, were carried out to investigate the rationality of 2D simplification. The effects of thermophysical properties of the phase change material, size of the container along the direction perpendicular to the 2D cross-section, as well as wall superheat were taken into consideration for a systematic and detailed comparison. It was shown that a small length of the container perpendicular to 2D plane will result in a confine space to limit the development of velocity distribution (i.e., parabolic velocity profile) due to the end effects, leading to to an almost identical melting rate to that obtained by the 2D simplified case. A larger size indicates stronger thermal convection (bulk uniform velocity profile) and faster melting rate. When fixing a large size of the container perpendicular to the 2D plane, decreasing the heating temperature and increasing the viscosity of liquid PCM (e.g., by adding nanoparticles) reduce the discrepancy between 2D and 3D simulation results.

Sign in / Sign up

Export Citation Format

Share Document