scholarly journals On orientation memory in high density polyethylene – carbon nanofibers composites

e-Polymers ◽  
2017 ◽  
Vol 17 (4) ◽  
pp. 303-310 ◽  
Author(s):  
Mircea Chipara ◽  
Brian Jones ◽  
Dorina M. Chipara ◽  
Jianhua Li ◽  
Karen Lozano ◽  
...  
Keyword(s):  
Melting Temperature ◽  
Carbon Nanofibers ◽  
Crystalline Phase ◽  
High Density Polyethylene ◽  
Room Temperature ◽  
Uniaxial Stress ◽  
High Density ◽  
Two Dimensional ◽  
Uniaxial Stretching ◽  
X Ray

AbstractAn orientation memory effect in high density polyethylene (HDPE) filled with vapor grown carbon nanofibers (VGCNF) is reported. Two-dimensional X-ray (2DXR) confirmed the reorientation of HDPE crystallites upon the uniaxial stretching of HDPE and HDPE filled by VGCNFs. This anisotropy of 2DXR spectra was decreased by heating all stretched samples (loaded or not loaded by VGCNFs) from room to the melting temperature of HDPE. Upon cooling these samples to room temperature, it was noticed that only the nanocomposite retained a weak partial (uniaxial) order, while HDPE showed a completely isotropic 2DXR spectrum. It was concluded that during the stretching of nanocomposites the crystallites and VGCNFs were aligned along the uniaxial stress. Upon heating, the crystalline phase was melted, while the orientation of the VGCNFs was not significantly disturbed. The recrystallization of the polymer started preferentially from the VGCNF – polymer interphase, resulting into an anisotropic crystalline structure.

scholarly journals Microbeam two-dimensional small-angle X-ray scattering investigating the effects of reduced graphene oxide on local microstructures of high-density polyethylene/reduced graphene oxide nanocomposite bars

2019 ◽  
Vol 6 (2) ◽  
pp. 181866 ◽  
Author(s):  
Guibin Yao ◽  
Tianchen Duan ◽  
Enyi Chi ◽  
Pengran Guo ◽  
Yiguo Li ◽  
...  
Keyword(s):  
Mechanical Properties ◽  
Graphene Oxide ◽  
Reduced Graphene Oxide ◽  
Small Angle ◽  
High Density Polyethylene ◽  
High Density ◽  
Two Dimensional ◽  
X Ray ◽  
X Ray Scattering ◽  
Reduced Graphene

It has been reported that the introduction of reduced graphene oxide (RGO) can enhance the crystallization and orientation of high-density polyethylene (HDPE) matrix and thus improve the mechanical properties of HDPE/RGO nanocomposites. In this study, the local microstructures and orientations in different regions of HDPE/RGO bars with varied RGO contents were further explored by two-dimensional small-angle X-ray scattering using a microbeam technique. It is unveiled that the orientation orderings of each position is intensified with increasing RGO amount, and of particular interest is the observation of the slight change of the ordering degrees in diverse zones of HDPE/RGO nanocomposite bars, indicating that RGO imposes a uniform enhancing effect upon HDPE matrix within different areas and consequently induces an effective increase of the mechanical properties of HDPE/RGO nanocomposites.

Composition and Surface Topography Effects on Apatite-Forming Ability of Ceramic-Polymer Composites

2003 ◽  
Vol 774 ◽  
Author(s):  
Susan M. Rea ◽  
Serena M. Best ◽  
William Bonfield
Keyword(s):  
Surface Topography ◽  
High Density Polyethylene ◽  
High Density ◽  
Apatite Layer ◽  
Biologically Active ◽  
Human Blood Plasma ◽  
Apatite Formation ◽  
Polyethylene Matrix ◽  
Composite Surface ◽  
X Ray

AbstractHAPEXTM (40 vol% hydroxyapatite in a high-density polyethylene matrix) and AWPEX (40 vol% apatite-wollastonite glass ceramic in a high density polyethylene matrix) are composites designed to provide bioactivity and to match the mechanical properties of human cortical bone. HAPEXTM has had clinical success in middle ear and orbital implants, and there is great potential for further orthopaedic applications of these materials. However, more detailed in vitro investigations must be performed to better understand the biological interactions of the composites and so the bioactivity of each material was assessed in this study. Specifically, the effects of controlled surface topography and ceramic filler composition on apatite layer formation in acellular simulated body fluid (SBF) with ion concentration similar to those of human blood plasma were examined. Samples were prepared as 1 cm × 1 cm × 1 mm tiles with polished, roughened, or parallel-grooved surface finishes, and were incubated in 20 ml of SBF at 36.5 °C for 1, 3, 7, or 14 days. The formation of a biologically active apatite layer on the composite surface after immersion was demonstrated by thin-film x-ray diffraction (TF-XRD), environmental scanning electron microscopy (ESEM) imaging and energy dispersive x-ray (EDX) analysis. Variations in sample weight and solution pH over the period of incubation were also recorded. Significant differences were found between the two materials tested, with greater bioactivity in AWPEX than HAPEXTM overall. Results also indicate that within each material the surface topography is highly important, with rougher samples correlated to earlier apatite formation.

scholarly journals Enhanced Water Resistance of Recycled Newspaper/High Density Polyethylene Composite Laminates via Hydrophobic Modification of Newspaper Laminas

Polymers ◽  
2021 ◽  
Vol 13 (3) ◽  
pp. 421
Author(s):  
Binwei Zheng ◽  
Weiwei Zhang ◽  
Litao Guan ◽  
Jin Gu ◽  
Dengyun Tu ◽  
...  
Keyword(s):  
Stearic Acid ◽  
Photoelectron Spectroscopy ◽  
Composite Laminates ◽  
High Density Polyethylene ◽  
Water Resistance ◽  
Laminated Composite ◽  
High Strength ◽  
High Water ◽  
High Density ◽  
X Ray

A high strength recycled newspaper (NP)/high density polyethylene (HDPE) laminated composite was developed using NP laminas as reinforcement and HDPE film as matrix. Herein, NP fiber was modified with stearic acid (SA) to enhance the water resistance of the NP laminas and NP/HDPE composite. The effects of heat treatment and SA concentration on the water resistance and tensile property of NP and composite samples were investigated. The chemical structure of the NP was characterized with X-ray diffractometer, X-ray photoelectron spectroscopy and attenuated total reflectance Fourier transform infrared spectra techniques. The surface and microstructure of the NP sheets were observed by scanning electron microscopy. An expected high-water resistance of NP sheets was achieved due to a chemical bonding that low surface energy SA were grafted onto the modified NP fibers. Results showed that the hydrophobicity of NP increased with increasing the stearic acid concentration. The water resistance of the composite laminates was depended on the hydrophobicity of the NP sheets. The lowest value of 2 h water absorption rate (3.3% ± 0.3%) and thickness swelling rate (2.2% ± 0.4%) of composite were obtained when the SA concentration was 0.15 M. In addition, the introduction of SA can not only enhance the water resistance of the composite laminates, but also reduce the loss of tensile strength in wet conditions, which shows potential in outdoor applications.

Improvement of the Properties of Polyethylene with Chlorinated Polyethylene (CPE)

2003 ◽  
Vol 11 (2) ◽  
pp. 115-122
Author(s):  
Kálmán Marossy ◽  
Pál Bárczy
Keyword(s):  
High Density Polyethylene ◽  
Industrial Applications ◽  
Mechanical Tests ◽  
High Density ◽  
Structural Units ◽  
Chlorinated Polyethylene ◽  
X Ray ◽  
Dynamic Mechanical ◽  
X Ray Scattering ◽  
Multiphase Systems

Blends of high density polyethylene (HDPE) and chlorinated polyethylene (CPE) have been tested across the whole concentration range. Polyethylene is used to modify the properties of CPE in the elastomer industry, but modification of the properties of polyethylene with CPE is still not usual. Conventional mechanical tests and dynamic mechanical tests were carried out. The blends were found to be multiphase systems of excellent technological compatibility. Between 10 and 15% by weight CPE increased the modulus of polyethylene. X-ray scattering studies showed that the blends contained structural units not present either in the polyethylene or in the CPE. The blends were melt processable and may have industrial applications, too.

Surface Spectroscopic Signatures of Mechanical Deformation in High-Density Polyethylene (HDPE)

2018 ◽  
Vol 72 (7) ◽  
pp. 1057-1068 ◽  
Author(s):  
Shawn C. Averett ◽  
Steven K. Stanley ◽  
Joshua J. Hanson ◽  
Stacey J. Smith ◽  
James E. Patterson
Keyword(s):  
High Density Polyethylene ◽  
Cold Drawing ◽  
Mechanical Deformation ◽  
Sum Frequency Generation ◽  
High Density ◽  
X Ray ◽  
Sum Frequency ◽  
Surface Normal ◽  
Methylene Groups ◽  
Spectroscopic Signatures

High-density polyethylene (HDPE) has been extensively studied, both as a model for semi-crystalline polymers and because of its own industrial utility. During cold drawing, crystalline regions of HDPE are known to break up and align with the direction of tensile load. Structural changes due to deformation should also manifest at the surface of the polymer, but until now, a detailed molecular understanding of how the surface responds to mechanical deformation has been lacking. This work establishes a precedent for using vibrational sum-frequency generation (VSFG) spectroscopy to investigate changes in the molecular-level structure of the surface of HDPE after cold drawing. X-ray diffraction (XRD) was used to confirm that the observed surface behavior corresponds to the expected bulk response. Before tensile loading, the VSFG spectra indicate that there is significant variability in the surface structure and tilt of the methylene groups away from the surface normal. After deformation, the VSFG spectroscopic signatures are notably different. These changes suggest that hydrocarbon chains at the surface of visibly necked HDPE are aligned with the direction of loading, while the associated methylene groups are oriented with the local C2 v symmetry axis roughly parallel to the surface normal. Small amounts of unaltered material are also found at the surface of necked HDPE, with the relative amount of unaltered material decreasing as the amount of deformation increases. Aspects of the nonresonant SFG response in the transition zone between necked and undeformed polymer provide additional insight into the deformation process and may provide the first indication of mechanical deformation. Nonlinear surface spectroscopy can thus be used as a noninvasive and nondestructive tool to probe the stress history of a HPDE sample in situations where X-ray techniques are not available or not applicable. Vibrational sum-frequency generation thus has great potential as a platform for material state awareness (MSA) and should be considered as part of a broader suite of tools for such applications.

Morphology of Silver Thin Films Deposited on TiO2(110) Surfaces

1998 ◽  
Vol 05 (01) ◽  
pp. 387-392 ◽  
Author(s):  
D. Abriou ◽  
D. Gagnot ◽  
J. Jupille ◽  
F. Creuzet
Keyword(s):  
Photoelectron Spectroscopy ◽  
Room Temperature ◽  
Oxygen Vacancies ◽  
Two Dimensional ◽  
Silver Films ◽  
X Ray ◽  
Force Microscopy ◽  
Atomic Force ◽  
Silver Deposits ◽  
Silver Thin Films

The growth mode of silver films deposited at room temperature on TiO 2(110) surfaces has been examined by means of atomic force microscopy (AFM) and X-ray photoelectron spectroscopy (XPS) in ultrahigh vacuum (UHV) conditions, On clean vacancy-free TiO 2(110) surfaces, 0.1-nm-thick (on average) Ag deposits form a two-dimensional (2D) layer. When the thickness of the silver overlayer is increased, 3D clusters are shown to appear while the 2D film is preserved, furthermore, the influence of surface oxygen vacancies on the growth of Ag/TiO 2(110) is evidenced by well-characterized differences in the morphology of 9-nm-thick silver deposits.

Fabrication and characterization of microwave cured high-density polyethylene/carbon nanotube and polypropylene/carbon nanotube composites

2019 ◽  
Vol 53 (15) ◽  
pp. 2091-2104 ◽  
Author(s):  
Gaurav Arora ◽  
Himanshu Pathak ◽  
Sunny Zafar
Keyword(s):  
Carbon Nanotube ◽  
High Density Polyethylene ◽  
High Density ◽  
Uniaxial Tensile ◽  
Uniaxial Tensile Test ◽  
X Ray Diffraction ◽  
X Ray ◽  
Nanotube Composites ◽  
Carbon Nanotube Composites ◽  
Scanning Electron

Carbon nanotubes have been used as reinforcements in polymers due to their high elasticity, flexibility, and thermal conductivity. In this study, pellets of high-density polyethylene +20 wt% carbon nanotube and polypropylene +20 wt% carbon nanotube were cured using microwave energy. X-ray diffraction, differential scanning calorimetry, thermogravimetric analysis, uniaxial tensile test, and scanning electron microscopy was used to study morphology, thermal stability, and mechanical performance of the microwave-cured composites. X-ray diffraction analysis confirmed the bonding between the polymer and carbon nanotube as the peaks shifted and intensified. From the thermal study, it was observed that melting point of the composites is affected by microwave curing and the crystallinity of high-density polyethylene/carbon nanotube and polypropylene/carbon nanotube changed by 57.67% and 47.28%, respectively. Results of the uniaxial tensile test indicated that Young’s modulus of microwave cured high-density polyethylene/carbon nanotube and polypropylene/carbon nanotube composites were improved by 295% and 787.8%, respectively. Scanning electron microscopic fractography shows the stretching of polymer over-lapped on carbon nanotubes in the direction of the applied load.

scholarly journals Quasi-hydrostatic equation of state of silicon up to 1 megabar at ambient temperature

2019 ◽  
Vol 9 (1) ◽  
Author(s):  
Simone Anzellini ◽  
Michael T. Wharmby ◽  
Francesca Miozzi ◽  
Annette Kleppe ◽  
Dominik Daisenberger ◽  
...  
Keyword(s):  
Equation Of State ◽  
Room Temperature ◽  
Uniaxial Stress ◽  
Sample Volume ◽  
X Ray Diffraction ◽  
Experimental Conditions ◽  
X Ray ◽  
Pressure Medium ◽  
Diamond Anvil ◽  
Isothermal Equation

Abstract The isothermal equation of state of silicon has been determined by synchrotron x-ray diffraction experiments up to 105.2 GPa at room temperature using diamond anvil cells. A He-pressure medium was used to minimize the effect of uniaxial stress on the sample volume and ruby, gold and tungsten pressure gauges were used. Seven different phases of silicon have been observed along the experimental conditions covered in the present study.

Structural evolution of melt-drawn transparent high-density polyethylene during heating and annealing: Synchrotron small-angle X-ray scattering study

2010 ◽  
Vol 46 (9) ◽  
pp. 1866-1877 ◽  
Author(s):  
Zhiyong Jiang ◽  
Yujing Tang ◽  
Jens Rieger ◽  
Hans-Friedrich Enderle ◽  
Dieter Lilge ◽  
...  
Keyword(s):  
Small Angle ◽  
High Density Polyethylene ◽  
Structural Evolution ◽  
High Density ◽  
X Ray ◽  
X Ray Scattering ◽  
Scattering Study ◽  
Ray Scattering

Spinel solid solutions in the systems MgAl2O4–ZnAl2O4 and MgAl2O4–Mg2TiO4

1997 ◽  
Vol 12 (10) ◽  
pp. 2584-2588 ◽  
Author(s):  
M. A. Petrova ◽  
G. A. Mikirticheva ◽  
A. S. Novikova ◽  
V. F. Popova
Keyword(s):  
Solid Solution ◽  
Phase Diagrams ◽  
Melting Temperature ◽  
Solid Solutions ◽  
Spinel Structure ◽  
Room Temperature ◽  
Binary Systems ◽  
Continuous Series ◽  
X Ray ◽  
Spinel Solid Solutions

Phase relations in two binary systems MgAl2O4–ZnAl2O4 and MgAl2O4–Mg2TiO4 have been studied and phase diagrams for them have been constructed. Based on the data of x-ray phase and crystal-optical analyses, the formation of a continuous series of solid solutions with spinel structure between the terminal members of the systems studied has been established. In the MgAl2O4–ZnAl2O4 system the solid solution is stable in the range from room temperature to melting temperature. In the MgAl2O4–Mg2TiO4 system the solid solution decomposes below 1380 °C, yielding the formation of limited regions of homogeneity on the basis of MgAlM2O4 and Mg2+2δ Ti1–δO4. Decomposition of the solid solution is accompanied by crystallization of MgTiO3.

Sign in / Sign up

Export Citation Format

Share Document