Constraint Effects on Torque-Actuated Bistable Energy Harvesters

2016 ◽  
Vol 3 (1) ◽  
Author(s):  
Daniel A. Porter ◽  
Thomas A. Berfield
Keyword(s):  
Boundary Conditions ◽  
Polyvinylidene Fluoride ◽  
Load Resistance ◽  
Resonant Frequencies ◽  
Energy Harvesters ◽  
Optimal Load ◽  
3D Printed ◽  
Frequency Sweeps ◽  
Constraint Effects ◽  
Bistable Device

AbstractThe effect of boundary conditions on a bistable device that buckles into an “S” shape and utilizes polyvinylidene fluoride is evaluated. Four permutations with different center constraints are the perfectly pinned circular steel, rigid glued circular steel, 3×1 and 5×1 3D printed rectangle polylactic acid prototypes. Using a load of 30 MΩ, which was close to the optimal load resistance, frequency sweeps in the forward and reverse directions indicated different nonlinearities depending on if the device is buckled or not. Peak resonant frequencies for the devices are around 18 to 30 Hz with bistable actuation occurring as low as 0.3

scholarly journals Load Resistance Optimization of a Broadband Bistable Piezoelectric Energy Harvester for Primary Harmonic and Subharmonic Behaviors

2021 ◽  
Vol 13 (5) ◽  
pp. 2865 ◽  
Author(s):  
Sungryong Bae ◽  
Pilkee Kim
Keyword(s):  
Energy Harvester ◽  
Load Resistance ◽  
Oscillation Period ◽  
Ambient Vibration ◽  
Ambient Vibrations ◽  
Frequency Dependency ◽  
Energy Harvesters ◽  
Piezoelectric Energy ◽  
Optimal Load ◽  
Bistable Energy Harvester

In this study, optimization of the external load resistance of a piezoelectric bistable energy harvester was performed for primary harmonic (period-1T) and subharmonic (period-3T) interwell motions. The analytical expression of the optimal load resistance was derived, based on the spectral analyses of the interwell motions, and evaluated. The analytical results are in excellent agreement with the numerical ones. A parametric study shows that the optimal load resistance depended on the forcing frequency, but not the intensity of the ambient vibration. Additionally, it was found that the optimal resistance for the period-3T interwell motion tended to be approximately three times larger than that for the period-1T interwell motion, which means that the optimal resistance was directly affected by the oscillation frequency (or oscillation period) of the motion rather than the forcing frequency. For broadband energy harvesting applications, the subharmonic interwell motion is also useful, in addition to the primary harmonic interwell motion. In designing such piezoelectric bistable energy harvesters, the frequency dependency of the optimal load resistance should be considered properly depending on ambient vibrations.

Effects of Downstream Structures on Aero Elastic Energy Harvesters From Wake-Induced Vibration

2019 ◽  
Vol 141 (7) ◽  
Author(s):  
Pakorn Uttayopas ◽  
Chawalit Kittichaikarn
Keyword(s):  
Cantilever Beam ◽  
Polyvinylidene Fluoride ◽  
Bluff Body ◽  
Electrical Energy ◽  
Load Resistance ◽  
High Amplitude ◽  
Triangular Prism ◽  
Energy Harvesters ◽  
Amplitude Vibration ◽  
And Behavior

An upstream cylindrical bluff body connected to a tip body via an aluminum cantilever beam was tested as energy harvester in a wind tunnel. The characteristics and behavior of the different tip body configurations and lengths of aluminum cantilever beam were studied to optimize design to extract wind energy. Particular attention was paid to measure vibration amplitude and frequency response as a function of reduced velocity. Dynamic response showed that the device's behavior was dependent on both tip body shape and cantilever beam length. Flow visualization tests showed that high amplitude vibration was obtainable when a vortex was fully formed on each side of the downstream tip body. This was exemplified in a symmetrical triangular prism tip body at L/D1 = 5, where its structure's vibration frequency was close to its natural frequency. At such configuration, electrical energy was captured using a polyvinylidene fluoride (PVDF) piezoelectric beam of different load resistances, where an optimized load resistance could be found for each Reynolds number. Although power output and efficiency obtained were considerably weak when compared to those of traditional wind turbine, the design merits further research to improve its performance under various circumstances.

scholarly journals Load Resistance Optimization of Bi-Stable Electromagnetic Energy Harvester Based on Harmonic Balance

Sensors ◽  
2021 ◽  
Vol 21 (4) ◽  
pp. 1505
Author(s):  
Sungryong Bae ◽  
Pilkee Kim
Keyword(s):  
External Load ◽  
Harmonic Balance ◽  
Energy Harvester ◽  
Load Resistance ◽  
Electromagnetic Energy ◽  
Analytic Approach ◽  
Accurate Estimation ◽  
Vibration Source ◽  
Optimal Load ◽  
Matching Techniques

In this study, a semi-analytic approach to optimizing the external load resistance of a bi-stable electromagnetic energy harvester is presented based on the harmonic balance method. The harmonic balance analyses for the primary harmonic (period-1T) and two subharmonic (period-3T and 5T) interwell motions of the energy harvester are performed with the Fourier series solutions of the individual motions determined by spectral analyses. For each motion, an optimization problem for maximizing the output power of the energy harvester is formulated based on the harmonic balance solutions and then solved to estimate the optimal external load resistance. The results of a parametric study show that the optimal load resistance significantly depends on the inductive reactance and internal resistance of a solenoid coil––the higher the oscillation frequency of an interwell motion (or the larger the inductance of the coil) is, the larger the optimal load resistance. In particular, when the frequency of the ambient vibration source is relatively high, the non-linear dynamic characteristics of an interwell motion should be considered in the optimization process of the electromagnetic energy harvester. Compared with conventional resistance-matching techniques, the proposed semi-analytic approach could provide a more accurate estimation of the external load resistance.

Performance analysis of a lever piezoelectric energy harvester for roadway applications

2021 ◽  
pp. 1045389X2110014
Author(s):  
Guangya Ding ◽  
Hongjun Luo ◽  
Jun Wang ◽  
Guohui Yuan
Keyword(s):  
Output Power ◽  
Energy Harvester ◽  
Open Circuit ◽  
Traffic Load ◽  
Energy Harvesters ◽  
Speed Sensor ◽  
Piezoelectric Energy ◽  
Optimal Load ◽  
Self Powered ◽  
Output Characteristics

A novel lever piezoelectric energy harvester (LPEH) was designed for installation in an actual roadway for energy harvesting. The model incorporates a lever module that amplifies the applied traffic load and transmits it to the piezoelectric ceramic. To observe the piezoelectric growth benefits of the optimized LPEH structure, the output characteristics and durability of two energy harvesters, the LPEH and a piezoelectric energy harvester (PEH) without a lever, were measured and compared by carrying out piezoelectric performance tests and traffic model experiments. Under the same loading condition, the open circuit voltages of the LPEH and PEH were 20.6 and 11.7 V, respectively, which represents a 76% voltage increase for the LPEH compared to the PEH. The output power of the LPEH was 21.51 mW at the optimal load, which was three times higher than that of the PEH (7.45 mW). The output power was linearly dependent on frequency and load, implying the potential application of the module as a self-powered speed sensor. When tested during 300,000 loading cycles, the LPEH still exhibited stable structural performance and durability.

Dynamic Response of Spiral Cantilever Undergoing Magnetic Coupling

2014 ◽  
Vol 14 (08) ◽  
pp. 1440021
Author(s):  
Xiaoling Bai ◽  
Yumei Wen ◽  
Ping Li ◽  
Jin Yang ◽  
Xiao Peng ◽  
...  
Keyword(s):  
Dynamic Response ◽  
Cantilever Beam ◽  
Magnetic Force ◽  
Coupling Effect ◽  
Magnetic Coupling ◽  
Resonant Frequencies ◽  
Energy Harvesters ◽  
Magnetic Transducer ◽  
Underlying Mechanisms ◽  
Tip Mass

Cantilever beams have found intensive and extensive uses as underlying mechanisms for energy transduction in sensors as well as in energy harvesters. In magnetoelectric (ME) transduction, the underlying cantilever beam usually will undergo magnetic coupling effect. As the beam itself is either banded with magnetic transducer or magnets, the dynamic motion of the cantilever can be modified due to the magnetic force between the magnets and ME sensors. In this study, the dynamic response of a typical spiral cantilever beam with magnetic coupling is investigated. The spiral cantilever acts as the resonator of an energy harvester with a tip mass in the form of magnets, and a ME transducer is positioned in the air gap and interacts with the magnets. It is expected that this spiral configuration is capable of performing multiple vibration modes over a small frequency range and the response frequencies can be magnetically tunable. The experimental results show that the magnetic coupling between the magnets and the transducer plays a favorable role in achieving tunable resonant frequencies and reducing the frequency spacings. This will benefits the expansion of the response band of a device and is especially useful in energy harvesting.

scholarly journals Tunable In Situ 3D-Printed PVDF-TrFE Piezoelectric Arrays

Sensors ◽  
2021 ◽  
Vol 21 (15) ◽  
pp. 5032
Author(s):  
Alec Ikei ◽  
James Wissman ◽  
Kaushik Sampath ◽  
Gregory Yesner ◽  
Syed N. Qadri
Keyword(s):  
3D Printing ◽  
Polyvinylidene Fluoride ◽  
Vinylidene Fluoride ◽  
Mechanical Strain ◽  
Pressure Sensors ◽  
Strain Ratio ◽  
Ex Situ ◽  
Order Of Magnitude ◽  
3D Printed

In the functional 3D-printing field, poly(vinylidene fluoride-co-trifluoroethylene) (PVDF-TrFE) has been shown to be a more promising choice of material over polyvinylidene fluoride (PVDF), due to its ability to be poled to a high level of piezoelectric performance without a large mechanical strain ratio. In this work, a novel presentation of in situ 3D printing and poling of PVDF-TrFE is shown with a d33 performance of up to 18 pC N−1, more than an order of magnitude larger than previously reported in situ poled polymer piezoelectrics. This finding paves the way forward for pressure sensors with much higher sensitivity and accuracy. In addition, the ability of in situ pole sensors to demonstrate different performance levels is shown in a fully 3D-printed five-element sensor array, accelerating and increasing the design space for complex sensing arrays. The in situ poled sample performance was compared to the performance of samples prepared through an ex situ corona poling process.

Vibration of Single- and Double-Layered Graphene Sheets

2011 ◽  
Vol 2 (1) ◽  
Author(s):  
Behrouz Arash ◽  
Quan Wang
Keyword(s):  
Molecular Dynamics ◽  
Boundary Conditions ◽  
Molecular Dynamics Simulations ◽  
Nonlocal Parameter ◽  
Small Scale ◽  
Graphene Sheets ◽  
Elastic Model ◽  
Resonant Frequencies ◽  
Nonlocal Continuum Theory ◽  
Dynamics Simulations

Free vibration of single- and double-layered graphene sheets is investigated by employing nonlocal continuum theory and molecular dynamics simulations. Results show that the classical elastic model overestimated the resonant frequencies of the sheets by a percentage as high as 62%. The dependence of small-scale effects, sizes of sheets, boundary conditions, and number of layers on vibrational characteristic of single- and double-layered graphene sheets is studied. The resonant frequencies predicted by the nonlocal elastic plate theory are verified by the molecular dynamics simulations, and the nonlocal parameter is calibrated through the verification process. The simulation results reveal that the calibrated nonlocal parameter depends on boundary conditions and vibrational modes. The nonlocal plate model is found to be indispensable in vibration analysis of grapheme sheets with a length less than 8 nm on their sides.

On 3D printing of electro-active PVDF-Graphene and Mn-doped ZnO nanoparticle-based composite as a self-healing repair solution for heritage structures

2021 ◽  
pp. 095440542110609
Author(s):  
Vinay Kumar ◽  
Rupinder Singh ◽  
Inderpreet Singh Ahuja
Keyword(s):  
3D Printing ◽  
Polyvinylidene Fluoride ◽  
Nano Particles ◽  
Zno Nanoparticle ◽  
Self Healing ◽  
Fused Deposition ◽  
Crack Repair ◽  
3D Printed ◽  
Doped Zno ◽  
Mn Doped

Construction is the part of human activity which is directly linked to urbanization for moving ahead on the path of growth and prosperity. Construction activities in past centuries are now part of our precious heritage. The repair and maintenance of heritage structures are of great importance for present-day researchers. One of the most common damage these century-long constructions faces are in form of surface cracks. In the present study, investigations were performed for a 3D printing-based customized solution for crack repair and maintenance of heritage structures. In this study, polyvinylidene fluoride (PVDF) polymer was reinforced with graphene (Gr) and Mn-doped ZnO nano-particles to prepare a smart composite material for crack repair and restoration. The composite was successfully 3D printed on fused deposition modeling (FDM) based 3D printer after investigating its rheological, thermal, and mechanical properties. The in-house developed composite was tested for smart characteristics to use as a programmable solution for filling cracks. The piezoelectric property and dielectric constant of 3D printed disk-shaped composite (PVDF-Gr-Mn-ZnO) were obtained after DC poling (to be used as stimulus) of the functional prototype. The results of the study suggest that the electro-active nature, volumetric change, and charge storing capacity of the additively manufactured composite may be used practically to acquire the shape of cavity/crack present in the constructed wall and repair the damages that occurred in a heritage site. The photoluminescence (PLS) and atomic force microscopy (AFM) analysis was used to ascertain the properties of the prepared composite. Also, the results obtained from the morphological analysis are reported to support the outcomes of the research.

Sign in / Sign up

Export Citation Format

Share Document