Natural Convection Heat Transfer in a Shell and Helical Coil Heat Exchanger Using non-Newtonian Nanofluids

2020 ◽  
Vol 15 (2) ◽  
Author(s):  
B. Anil Kumar Naik ◽  
A. Venu Vinod
Keyword(s):  
Heat Transfer ◽  
Heat Transfer Rate ◽  
Transfer Rate ◽  
Base Fluid ◽  
Convection Heat Transfer ◽  
Cuo Nanoparticles ◽  
Helical Coil ◽  
Natural Convection Heat Transfer ◽  
Coil Heat Exchanger ◽  
Coil Heat

AbstractNanofluids have gained much attention due to excellent thermal properties. In this study, natural convection heat transfer behavior of three different types of non-Newtonian nanofluids in a shell and helical coil heat exchanger has been investigated experimentally under unsteady state conditions. Nanofluids were prepared by dispersion of Al2O3, Fe2O3 and CuO nanoparticles in an aqueous solution of carboxymethyl cellulose (CMC) (base fluid). Nanofluids of different concentrations (0.2, 0.4, 0.6, 0.8 and 1.0 wt%) were prepared by dispersing Al2O3, Fe2O3 and CuO nanoparticles in base fluid using probe sonication process. In the present study, the effect of shell-side nanofluid concentration, tube-side fluid (heating medium) temperature and flow rate parameters on heat transfer has been investigated.Results indicated that the addition of nanofluid has intensified heat transfer as indicated by the higher temperature of nanofluid when compared to base fluid. Out of the three materials used in the study, CuO nanofluid attained the highest temperature because of its higher thermal conductivity. Heat transfer rate decreased with time continuously for all the experimental conditions. Enhancement in heat transfer initially was higher compared to later times. At longer time the enhancement is less due to the lower buoyancy forces prevailing due to lower driving force. A maximum enhancement in heat transfer rate of 29.5 % has been obtained initially. The effect of nanofluid concentration on heat transfer rate with time exhibited different behavior compared to the effect of inlet temperature and flow rate.

scholarly journals Experimental Research on Heat Transfer Characteristics of Helical Coil Heat Exchanger with Varying Pitch for laminar Fluid Flow

2019 ◽  
Vol 8 (3) ◽  
pp. 315-320
Keyword(s):  
Heat Transfer ◽  
Heat Exchanger ◽  
Heat Transfer Rate ◽  
Flow Rate ◽  
Transfer Rate ◽  
Helical Coil ◽  
Heat Transfer Characteristics ◽  
Transfer Characteristics ◽  
Coil Heat Exchanger ◽  
Coil Heat

To Study on rate of heat transfer in heat exchanger using helical coils has been studied by many researchers. There is less published literature available on varying pitch helical coil heat exchanger and detail characteristics of helical coil varying pitch by keeping constant curvature ratio considering heat exchange between fluid to fluid heat exchanger for laminar flow condition not available in the present available literature. Hence in present study three different coils with varying pitches are used to investigate the heat transfer characteristics of a Helical Coil Heat Exchanger. Hence coil of 25mm, 30mm, 35mm are used by keeping constant curvature ratio (=0.0667), experiment is conducted to study the influence of varying pitch on effectiveness, heat transfer rate, over all heat transfer co-efficient and Nusselt Number. The experiments is conducted in horizontal counter steady flow condition and changing the flow rate of hot fluid, pitch of helical coil heat exchanger. The results show that the varying pitch of helical coil heat exchanger has influence on heat transfer characteristics. The effectiveness of the helical coil heat exchanger is decreases with increase in mass flow rate of the hot fluid inside helical tube for varying pitch considered for study. The heat transfer rate of the helical coil heat exchanger is increases with increase in Dean Number of the hot fluid inside helical tube for varying pitch considered for study. The overall heat transfer coefficient increases with increasing hot water mass flow rate. The Nussult Number at different dean number increases for increasing helical coil pitch however the trend of average heat transfer rate for increasing M Number for varying pitch observed similar. By increasing the coil pitch of helical coil heat exchanger decreases Nussult Number, inside overall heat transfer coefficient, heat transfer rate and effectiveness.

Heat Transfer Analysis of Shell-and-Helical-Coil Heat Exchangers

2016 ◽  
Author(s):  
Anthony Edward Morris ◽  
C. S. Wei ◽  
Runar Unnthorsson ◽  
Robert Dell
Keyword(s):  
Heat Transfer ◽  
Heat Transfer Rate ◽  
Heat Exchangers ◽  
Transfer Rate ◽  
Green Roofs ◽  
Heat Transfer Analysis ◽  
Helical Coil ◽  
Straight Tube ◽  
Science And Art ◽  
Coil Heat

Since 2006, The Center for Innovation and Applied Technology (CIAT) at Cooper Union for the Advancement of Science and Art has been developing a system to use thermal pollution to heat the growth medium of green roofs. CIAT is researching various apparatus and techniques, including shell-and-tube and shell-and-coil heat exchangers, to improve its heated ground agricultural projects. There are limited recorded observations on shell-and-coil heat exchangers; therefore a laboratory work station was created of interchangeable components to test the efficiency of a variety of coil designs. This paper discusses the data collected on temperature, pressure, and flow rates for a straight tube and two different helical coils. The analysis of this data indicates the superiority of a helical coil design when compared to a straight tube design with respect to both rating and heat transfer rate. The same data analysis has lead to preliminary observations on how the contour properties of a helical coil influence the heat transfer rate through a coil. The authors intend to further this helical coil research to develop a useful mathematical model for determining efficient designs for shell-and-coil heat exchangers.

scholarly journals Effect of Fin Number and Position on Non-linear Characteristics of Natural Convection Heat Transfer in Internally Finned Horizontal Annulus

2021 ◽  
Vol 9 ◽  
Author(s):  
Kun Zhang ◽  
Yu Zhang ◽  
Xiaoyu Wang ◽  
Liangbi Wang
Keyword(s):  
Heat Transfer ◽  
Natural Convection ◽  
Heat Transfer Rate ◽  
Transfer Rate ◽  
Stokes Equations ◽  
Convection Heat Transfer ◽  
The Self ◽  
Natural Convection Heat Transfer ◽  
Convection Heat ◽  
Simpler Algorithm

Detailed numerical calculations are performed for investigating the effect of fin number and position on unsteady natural convection heat transfer in internally finned horizontal annulus. The SIMPLER algorithm with Quick scheme is applied for solving the Navier Stokes equations of flow and heat transfer. The results show that the heat transfer rate in annulus with fins increases with the increasing numbers of fin and Rayleigh numbers. For Ra = 2 × 105, the effect of numbers of fins and fins position at the bottom part on the unsteady solutions can be neglected, because the self-oscillation phenomenon is mainly affected by natural convection at the upper part of annulus. Although the fin positions cannot increase heat transfer rate significantly in the case of four fins, the self-oscillated solutions can be suppressed by altering fins position.

scholarly journals Numerical Study of Natural Convection Heat Transfer in a Porous Annulus Filled with a Cu-Nanofluid

Nanomaterials ◽  
2021 ◽  
Vol 11 (4) ◽  
pp. 990
Author(s):  
Lingyun Zhang ◽  
Yupeng Hu ◽  
Minghai Li
Keyword(s):  
Heat Transfer ◽  
Heat Transfer Rate ◽  
Transfer Rate ◽  
Volume Fraction ◽  
Convection Heat Transfer ◽  
Darcy Number ◽  
Radius Ratio ◽  
Natural Convection Heat Transfer ◽  
Nanoparticle Volume Fraction ◽  
Convection Heat

Natural convection heat transfer in a porous annulus filled with a Cu nanofluid has been investigated numerically. The Darcy–Brinkman and the energy transport equations are employed to describe the nanofluid motion and the heat transfer in the porous medium. Numerical results including the isotherms, streamlines, and heat transfer rate are obtained under the following parameters: Brownian motion, Rayleigh number (103–105), Darcy number (10−4–10−2), nanoparticle volume fraction (0.01–0.09), nanoparticle diameter (10–90 nm), porosity (0.1–0.9), and radius ratio (1.1–10). Results show that Brownian motion should be considered. The nanoparticle volume fraction has a positive effect on the heat transfer rate, especially with high Rayleigh number and Darcy number, while the nanoparticle diameter has an inverse influence. The heat transfer rate is enhanced with the increase of porosity. The radius ratio has a significant influence on the isotherms, streamlines, and heat transfer rate, and the rate is greatly enhanced with the increase of radius ratio.

scholarly journals Enhancement of natural convection heat transfer in concentric annular space using inclined elliptical cylinder

2020 ◽  
Vol 17 (2) ◽  
pp. 89-99
Author(s):  
Houssem Laidoudi
Keyword(s):  
Heat Transfer ◽  
Natural Convection ◽  
Aspect Ratio ◽  
Heat Transfer Rate ◽  
Inclination Angle ◽  
Transfer Rate ◽  
Convection Heat Transfer ◽  
Natural Convection Heat Transfer ◽  
Convection Heat ◽  
Elliptical Cross

The governing equations of continuity, momentum and energy are numerically solved to study the laminar natural convection heat transfer of Newtonian fluid confined within two concentric cylinders. The inner cylinder is elliptical cross-section with different aspect ratio E = 0.1 to 0.5 and it is considered to be hot, whereas the outer cylinder is circular and it is supposed to be cold.    The annular spacing between the cylinders is defined based on radii ratio (RR = 2.5). Also, the inner cylinder is inclined with an inclination angle (θ = 0 to 90). The main purpose of this study is to determine the effects of inclination angle (θ = 0° to 90°), aspect ratio of inner cylinder (E = 0.1 to 0.5), Prandtl number (Pr = 0.71 and 7.01) and Rayleigh number (Ra = 103 to 105) on fluid flow and heat transfer rate. The flow patterns and temperature distributions are potted in terms of streamlines and isotherms respectively. The obtained results showed that increase in inclination angle enhances the heat transfer rate of inner cylinder for all values of aspect ratio. Also, for the inclination angle          (θ = 90°), the decrease in aspect ratio (E) improves the heat transfer rate of inner cylinder.

Coil Heat Exchanger with the Nanofluid Filled Buffer Layer

2016 ◽  
Vol 831 ◽  
pp. 223-231 ◽  
Author(s):  
Robert Smusz ◽  
Joanna Wilk
Keyword(s):  
Heat Transfer ◽  
Heat Exchanger ◽  
Buffer Layer ◽  
Heat Transfer Rate ◽  
Transfer Rate ◽  
Waste Heat ◽  
Thermal Power ◽  
Transfer Coefficients ◽  
Coil Heat Exchanger ◽  
Coil Heat

The paper presents the preliminary design of the special heat exchanger. The device under consideration is the kind of immersed coil heat exchangers. It consists of three vertical coils: two coils are standard, water is used as a heating medium; one coil is filled by the refrigerant R134a which transfers the waste heat from refrigeration and air conditioning system during the boiling processes. In order to prevent the possible refrigerant leakage, the special buffer layer filled with the nanofluid is mounted in the Freon coil. Thermophysical properties of the nanofluid cause the intensification of the heat transfer through the buffer layer and the same increase of the heat transfer rate. Calculations of thermal power were made. Correlations of heat transfer coefficients in curved tubes, pressure drop correlations for flow through helical coil tubes and correlations describing the heat transfer in the buffer layer, were applied. Results of the calculations indicate of the influence of of Freon coil on the exchanger heat transfer rate. Heat power of Freon coil is about 7 – 25% of water coil thermal power. Thus, the waste heat applied significantly increases the exchanger heat transfer rate.

Natural Convection Heat Transfer With Horizontal Rectangular Fin Array Using Straight Knurling Patterns on Fins: An Experimental Study

2018 ◽  
Author(s):  
R. C. Chikurde ◽  
B. S. Kothavale ◽  
N. K. Sane
Keyword(s):  
Heat Transfer ◽  
Surface Roughness ◽  
Natural Convection ◽  
Heat Transfer Rate ◽  
Transfer Rate ◽  
Convection Heat Transfer ◽  
Flow Characteristics ◽  
Natural Convection Heat Transfer ◽  
Convection Heat ◽  
Heat Transfer Augmentation

Natural Convection heat transfer from horizontal rectangular fin array with various knurling patterns is studied experimentally to find the effect of varying surface roughness on the heat transfer rate. The experimental parametric study is performed to investigate the effect of knurl produced surface roughness of fin on heat transfer rate. The parameters like knurling height from base, knurling depth and fin spacing might affect the flow characteristics and hence it is investigated to find the effect on heat transfer coefficient. The knurling is usually accomplished using one or more very hard rollers that contain the reverse of the pattern to be imposed. The result of this study shows that there are some important geometric factors related to knurling affecting the design of fin arrays and also heat transfer augmentation of natural convection heat transfer is observed.

Sign in / Sign up

Export Citation Format

Share Document