Sensitivity enhancement of a folded beam MEMS capacitive accelerometer-based microphone for fully implantable hearing application

2018 ◽  
Vol 63 (6) ◽  
pp. 699-708 ◽  
Author(s):  
Apoorva Dwivedi ◽  
Gargi Khanna
Keyword(s):  
Microelectromechanical Systems ◽  
Bone Structure ◽  
Design Parameters ◽  
Comsol Multiphysics ◽  
Geometrical Parameters ◽  
Efficient Design ◽  
Capacitive Accelerometer ◽  
Biomedical Device ◽  
Device Geometry ◽  
The Stability

Abstract The present work attempts to enhance the sensitivity of a folded beam microelectromechanical systems (MEMS) capacitive accelerometer by optimising the device geometry. The accelerometer is intended to serve as a microphone in the fully implantable hearing application which can be surgically implanted in the middle ear bone structure. For the efficient design of the accelerometer as a fully implantable biomedical device, the design parameters such as size, weight and resonant frequency have been considered. The geometrical parameters are varied to obtain the optimum sensitivity considering the design constraints and the stability of the structure. The optimised design is simulated and verified using COMSOL MULTIPHYSICS 4.2. The stability of the device is ensured using eigenfrequency analysis. Optimised results of the device geometry are presented and discussed. The accelerometer has a sensing area of 1 mm2 and attains a nominal capacitance of 5.3 pF and an optimum sensitivity of 6.89 fF.

A microelectromechanical system (MEMS) capacitive accelerometer-based microphone with enhanced sensitivity for fully implantable hearing aid: a novel analytical approach

2020 ◽  
Vol 65 (6) ◽  
pp. 735-746
Author(s):  
Apoorva Dwivedi ◽  
Gargi Khanna
Keyword(s):  
Analytical Approach ◽  
Bone Structure ◽  
Design Parameters ◽  
Comsol Multiphysics ◽  
Implantable Hearing Aid ◽  
Microelectromechanical System ◽  
Capacitive Accelerometer ◽  
Enhanced Sensitivity ◽  
Mechanical Amplification ◽  
The Impact

AbstractThe present work proposes a novel, compact, intuitively simple and efficient structure to improve the sensitivity of a microelectromechanical system (MEMS) capacitive accelerometer using an arrangement of microlever as a displacement amplifier. The accelerometer is proposed to serve as a microphone in the fully implantable cochlear prosthetic system which can be surgically implanted at the middle ear bone structure. Therefore, the design parameters such as size, weight and resonant frequency require deliberation. The paper presents a novel analytical model considering the impact of the mechanical amplification along with the width of the microlever and the capacitive fringe effects on the performance of the sensor. The design is simulated and verified using COMSOL MULTIPHYSICS 4.2. The accelerometer is designed within a sensing area of 1 mm2 and accomplishes a nominal capacitance of 4.85 pF and an excellent sensitivity of 5.91 fF/g.

scholarly journals Biomimicry-Gradient-Based Algorithm as Applied to Photonic Devices Design: Inverse Design of Flat Plasmonic Metalenses

2021 ◽  
Vol 11 (12) ◽  
pp. 5436
Author(s):  
Kofi Edee
Keyword(s):  
High Performance ◽  
Figure Of Merit ◽  
Initial Conditions ◽  
Design Method ◽  
Optimal Solution ◽  
High Energy ◽  
Inverse Design ◽  
Design Parameters ◽  
Geometrical Parameters ◽  
Efficient Design

The classical adjoint-based topology optimization (TO) method, based on the use of a random continuous dielectric function as design variable distribution is known to be one of the timely efficient and fast optimization methods enable a very high performance functional optical devices. It relies on the computation of the gradient of a figure of merit (FOM) with respect to the design parameters. The gradient of the figure of merit (FOM) may then be used to update the design vector element in several senarios. One of the most common use scenarios consists of updating simultaneously all the design parameter vector elements. In a linear problem case involving a simply convex FOM-function shape, using the gradient information, it is a relatively easy to reach an optimal solution. In the case of constrained and non linear problems stated in an infinite and indeterminate design space, the conventional TO, a local optimizer, may require multiple restarts, with multiple initial points and multiple runs. The algorithm strongly depends on the initial conditions. In this paper, we report a global-like optimizer inspired by a wolf pack hunting, enabling efficient design of metasurfaces through their geometrical parameters. We apply the method to design a non periodic metasurface consisting of plasmonic metalenses, enabling a high energy flow focusing on a well-defined 2D focus spot. Numerical results show that the proposed inverse design method has a low sensitivity to initial conditions. In our design method of metalens, we optimize the full micro device at once, and demonstrate that the proposed method may provide both symmetric and more creative unexpected asymmetric on-axis metalenses even though under a normal illumination.

Parametric Optimization of Dental Implants

2020 ◽  
Vol 22 (4) ◽  
pp. 1061-1076
Author(s):  
Wafa Bensmain ◽  
Mohammed Benlebna ◽  
Boualem Serier ◽  
Bel Abbes ◽  
Bachir Bouiadjra
Keyword(s):  
Dental Implants ◽  
Clinical Success ◽  
Equivalent Stress ◽  
Radius Of Curvature ◽  
Geometrical Parameters ◽  
Neck Size ◽  
Biomechanical Behavior ◽  
Dynamic Charging ◽  
The Stability ◽  
Masticatory Process

AbstractOsseointegration is a fundamental phenomenon of dental implantology. It ensures the stability, the safety and the durability of dental implants and predictable clinical success in long-term. The geometric form of the implant is a defining parameter of osseointegration and implant-bone charge transfer. This is the essential constitutes of this study. In fact, we demonstrate using the finite elements method with tridimensional numerical computations, that the geometrical parameters of the implant conditionate the level and the repartition of the stresses, induced in the cortical bone and the spongy bone during the masticatory process, simulated here by dynamic charging. The effect of several parameters [size and conicity of the implant neck, size and radius of curvature of the implant apex] and the shape of the implant corps on the biomechanical behavior of the bone. The latest was analyzed in terms of variation of the equivalent stress induced in the bone. The purpose of this analysis was the developing of an implant form allowing stress relaxation, during the mastication process, in the living tissue.

Design of a wheeled wall climbing robot based on the performance of bio-inspired dry adhesive material

Robotica ◽  
2021 ◽  
pp. 1-14
Author(s):  
Hongkai Li ◽  
Xianfei Sun ◽  
Zishuo Chen ◽  
Lei Zhang ◽  
Hongchao Wang ◽  
...  
Keyword(s):  
Flat Surface ◽  
Thrust Force ◽  
Adhesion Force ◽  
Structure Design ◽  
Design Parameters ◽  
Climbing Robot ◽  
Adhesive Material ◽  
Ducted Fan ◽  
The Stability ◽  
Belt System

Abstract Inspired by gecko’s adhesive feet, a wheeled wall climbing robot is designed in this paper with the synchronized gears and belt system acting as the wheels by considering both motion efficiency and adhesive capability. Adhesion of wheels is obtained by the bio-inspired adhesive material wrapping on the outer surface of wheels. A ducted fan mounted on the back of the robot supplies thrust force for the adhesive material to generate normal and shear adhesion force whilemoving on vertical surfaces. Experimental verification of robot climbing on vertical flat surface was carried out. The stability and the effect of structure design parameters were analyzed.

scholarly journals Design and optimization of differential capacitive micro accelerometer for vibration measurement

2021 ◽  
Vol 30 (1) ◽  
pp. 19-27
Author(s):  
Kumar Gomathi ◽  
Arunachalam Balaji ◽  
Thangaraj Mrunalini
Keyword(s):  
Software Design ◽  
Proof Mass ◽  
Vibration Measurement ◽  
Design Parameters ◽  
Mechanical Sensitivity ◽  
Design And Optimization ◽  
Capacitive Accelerometer ◽  
Cross Axis ◽  
Micro Accelerometer

Abstract This paper deals with the design and optimization of a differential capacitive micro accelerometer for better displacement since other types of micro accelerometer lags in sensitivity and linearity. To overcome this problem, a capacitive area-changed technique is adopted to improve the sensitivity even in a wide acceleration range (0–100 g). The linearity is improved by designing a U-folded suspension. The movable mass of the accelerometer is designed with many fingers connected in parallel and suspended over the stationary electrodes. This arrangement gives the differential comb-type capacitive accelerometer. The area changed capacitive accelerometer is designed using Intellisuite 8.6 Software. Design parameters such as spring width and radius, length, and width of the proof mass are optimized using Minitab 17 software. Mechanical sensitivity of 0.3506 μm/g and Electrical sensitivity of 4.706 μF/g are achieved. The highest displacement of 7.899 μm is obtained with a cross-axis sensitivity of 0.47%.

Stability of Ring-Type MEMS Gyroscopes Subjected to Stochastic Angular Speed Fluctuation

2017 ◽  
Vol 139 (4) ◽  
Author(s):  
Samuel F. Asokanthan ◽  
Soroush Arghavan ◽  
Mohamed Bognash
Keyword(s):  
Angular Velocity ◽  
Degrees Of Freedom ◽  
Microelectromechanical Systems ◽  
Damping Ratio ◽  
Operating Conditions ◽  
System Stability ◽  
System Response ◽  
Ring Type ◽  
Mems Gyroscopes ◽  
The Stability

Effect of stochastic fluctuations in angular velocity on the stability of two degrees-of-freedom ring-type microelectromechanical systems (MEMS) gyroscopes is investigated. The governing stochastic differential equations (SDEs) are discretized using the higher-order Milstein scheme in order to numerically predict the system response assuming the fluctuations to be white noise. Simulations via Euler scheme as well as a measure of largest Lyapunov exponents (LLEs) are employed for validation purposes due to lack of similar analytical or experimental data. The response of the gyroscope under different noise fluctuation magnitudes has been computed to ascertain the stability behavior of the system. External noise that affect the gyroscope dynamic behavior typically results from environment factors and the nature of the system operation can be exerted on the system at any frequency range depending on the source. Hence, a parametric study is performed to assess the noise intensity stability threshold for a number of damping ratio values. The stability investigation predicts the form of threshold fluctuation intensity dependence on damping ratio. Under typical gyroscope operating conditions, nominal input angular velocity magnitude and mass mismatch appear to have minimal influence on system stability.

scholarly journals A Two-Round Optimization Design Method for Aerostatic Spindles Considering the Fluid–Structure Interaction Effect

2021 ◽  
Vol 11 (7) ◽  
pp. 3017
Author(s):  
Qiang Gao ◽  
Siyu Gao ◽  
Lihua Lu ◽  
Min Zhu ◽  
Feihu Zhang
Keyword(s):  
Optimal Design ◽  
Optimization Design ◽  
Design Method ◽  
Fluid Structure Interaction ◽  
Design Procedure ◽  
Design Parameters ◽  
Geometrical Parameters ◽  
Fluid Structure ◽  
Structure Interaction ◽  
Aerostatic Spindle

The fluid–structure interaction (FSI) effect has a significant impact on the static and dynamic performance of aerostatic spindles, which should be fully considered when developing a new product. To enhance the overall performance of aerostatic spindles, a two-round optimization design method for aerostatic spindles considering the FSI effect is proposed in this article. An aerostatic spindle is optimized to elaborate the design procedure of the proposed method. In the first-round design, the geometrical parameters of the aerostatic bearing were optimized to improve its stiffness. Then, the key structural dimension of the aerostatic spindle is optimized in the second-round design to improve the natural frequency of the spindle. Finally, optimal design parameters are acquired and experimentally verified. This research guides the optimal design of aerostatic spindles considering the FSI effect.

Hydro-Mechanical Coupled Analysis of the Stability of Surrounding Rock Mass of Underground Water-Sealed Oil Storage

2013 ◽  
Vol 405-408 ◽  
pp. 402-405 ◽  
Author(s):  
Yun Jie Zhang ◽  
Tao Xu ◽  
Qiang Xu ◽  
Lin Bu
Keyword(s):  
Rock Mass ◽  
Underground Water ◽  
Surrounding Rock ◽  
Comsol Multiphysics ◽  
Coupled Analysis ◽  
Coupling Theory ◽  
Oil Storage ◽  
Stability Of Surrounding Rock ◽  
Straight Wall ◽  
The Stability

Based on the fluid-solid coupling theory, we study the stability of surrounding rock mass around underground oil storage in Huangdao, Shandong province, analyze the stress of the surrounding rock mass around three chambers and the displacement change of several key monitoring points after excavation and evaluate the stability of surrounding rock mass using COMSOL Multiphysics software. Research results show that the stress at both sides of the straight wall of cavern increases, especially obvious stress concentration forms at the corners of the cavern, and the surrounding rock mass moves towards the cavern after excavation. The stress and displacement of the surrounding rock mass will increase accordingly after setting the water curtains, but the change does not have a substantive impact on the stability of surrounding rock mass.

Investigation of sustainability of lubricated journal bearing under relevant design parameters

2018 ◽  
Vol 70 (4) ◽  
pp. 789-804 ◽  
Author(s):  
M.M. Shahin ◽  
Mohammad Asaduzzaman Chowdhury ◽  
Md. Arefin Kowser ◽  
Uttam Kumar Debnath ◽  
M.H. Monir
Keyword(s):  
Aspect Ratio ◽  
Elastic Strain ◽  
Journal Bearing ◽  
Design Parameters ◽  
Content Type ◽  
Computational Fluid Dynamics Cfd ◽  
Stress Formation ◽  
Bearing Design ◽  
The Stability ◽  
Bearing Friction

Purpose The purposes of the present study are to ensure higher sustainability of journal bearings under different applied loads and to observe bearing performances such as elastic strain, total deformation and stress formation. Design/methodology/approach A journal bearing test rig was used to determine the effect of the applied load on the bearing friction, film thickness, lubricant film pressure, etc. A steady-state analysis was performed to obtain the bearing performance. Findings An efficient aspect ratio (L/D) range was obtained to increase the durability or the stability of the bearing while the bearing is in the working condition by using SAE 5W-30 oil. The results from the study were compared with previous studies in which different types of oil and water, such as Newtonian fluid (NF), magnetorheological fluid (MRF) and nonmagnetorheological fluid (NMRF), were used as the lubricant. To ensure a preferable aspect ratio range (0.25-0.50), a computational fluid dynamics (CFD) analysis was conducted by ANSYS; the results show a lower elastic strain and deformation within the preferable aspect ratio (0.25-0.50) rather than a higher aspect ratio using the SAE 5W-30 oil. Originality/value It is expected that the findings of this study will contribute to the improvement of the bearing design and the bearing lubricating system.

Effect of Geometric Parameters of New Semisubmersible Platform on Stability and Hydrodynamic Performance

2021 ◽  
Author(s):  
Tianying Wang ◽  
Yanjun Zhou ◽  
Honglin Tang ◽  
Shihua Zhang ◽  
Haiqing Tian
Keyword(s):  
Geometric Parameters ◽  
Hydrodynamic Performance ◽  
Geometrical Parameters ◽  
Main Body ◽  
Floating Bodies ◽  
Full Picture ◽  
New Type ◽  
Design Plan ◽  
The Stability ◽  
Shape Characteristics

Abstract The JCSM concept (short for Jackup Combined Semisubmersible Multifunction Platform) is a new type of semisubmersible platform presented by the first author, which overcomes the shortcomings of the available semisubmersible platforms, and combines the advantages of the traditional semisubmersible platform, the Jackup platform and the new FPSO concept - IQFP. Due to the complicated interaction between stability and hydrodynamic performance, it is necessary to explore the effect of geometrical parameters of the main body on the stability and hydrodynamic performance in order to obtain the optimal design plan of a JCSM platform. Firstly, the structure components and innovations of the JCSM were briefly reviewed in order to facilitate readers to understand its full picture. Then, six independent geometric parameters were selected by carefully studying the shape characteristics of the initial design plan of a JCSM study case. Furthermore, the stability heights and motion responses of various floating bodies of the JCSM case with different geometric parameters in wave were calculated using boundary element method based on potential flow theory. Lastly, effect of the shape parameters on stability and hydrodynamic performance of the JCSM was qualitatively evaluated. The research would shed lights on the shape design of the JCSM main body.

Sign in / Sign up

Export Citation Format

Share Document