scholarly journals The Study of Phase Transformations of AlSi9Cu3 Alloy by DSC Method

2016 ◽  
Vol 16 (4) ◽  
pp. 109-112 ◽  
Author(s):  
J. Piątkowski ◽  
R. Przeliorz ◽  
A. Gontarczyk
Keyword(s):  
Phase Transformations ◽  
Cast Alloy ◽  
Eutectic Mixture ◽  
Scanning Calorimetry ◽  
Total Enthalpy ◽  
Silicon Crystals ◽  
Endothermic Reactions ◽  
Structural Tests ◽  
Dsc Method ◽  
Transformation Enthalpy

Abstract With the use of differential scanning calorimetry (DSC), the characteristic temperatures and enthalpy of phase transformations were defined for commercial AlSi9Cu3 cast alloy (EN AC-46000) that is being used for example for pressurized castings for automotive industry. During the heating with the speed of 10°C·min−1 two endothermic effects has been observed. The first appears at the temperature between 495 °C and 534 °C, and the other between 555 °C and 631 °C. With these reactions the phase transformation enthalpy comes up as +6 J g−1 and +327 J g−1. During the cooling with the same speed, three endothermic reactions were observed at the temperatures between 584 °C and 471 °C. The total enthalpy of the transitions is – 348 J g−1. Complimentary to the calorimetric research, the structural tests (SEM and EDX) were conducted on light microscope Reichert and on scanning microscope Hitachi S-4200. As it comes out of that, there are dendrites in the structure of α(Al) solution, as well as the eutectic (β) silicon crystals, and two types of eutectic mixture: double eutectic α(Al)+β(Si) and compound eutectic α+Al2Cu+β.

Differentiated Scanning Calorimetry of Model Systems with Cocoa Butter

Food Industry ◽  
2020 ◽  
Vol 5 (2) ◽  
pp. 29-36
Author(s):  
Alexander Vereshchagin ◽  
Irina Reznichenko ◽  
Nikolay Bychin
Keyword(s):  
Cocoa Butter ◽  
Palm Olein ◽  
Palm Stearin ◽  
Model Systems ◽  
Scanning Calorimetry ◽  
Glucose Syrup ◽  
Polymorphic Modifications ◽  
Confectionery Products ◽  
System Temperature ◽  
Dsc Method

The article concerns the research specificity of model systems such as cocoa butter – palm olein, cocoa butter – sucrose and cocoa butter – glucose syrup by the differential scanning calorimetry (DSC) method. The researchers run experiments in the temperature range from –100 to –50°C at a heating rate of 10 °C/min. In the cacao butter – palm olein system an eutectic occurs with a palm olein content of 30.0 % indicating the limited solubility of palm olein in cocoa butter. In the cocoa butter – sucrose system, cocoa butter crystallizes as in the α-form (10,0– 30,0; 60.0–90.0 % MK), and as a mixture of α-and β-forms of MK (40.0; 50,0; 70,0 and 80.0 %). Sucrose stabilizes low-temperature polymorphic modifications of cocoa butter. In the cocoa butter – glucose syrup system, temperature of samples melting is 21-22 °C. This composition is promising for use as a filling of confectionery products and glazes production. In this regard, a man can use glucose syrup only in the candy cases production. The role of surfactants used for the formation and stabilization of cocoa butter polymorphs and increasing the thermal stability of the shock-lad without the introduction of palm stearin requires separate consideration.

MICROSTRUCTURAL EVOLUTION OF Al-Cu-Mg-Ag ALLOY WITH TRACE Zr ADDITION DURING TWO-STEP HOMOGENIZATION

2009 ◽  
Vol 23 (06n07) ◽  
pp. 855-862 ◽  
Author(s):  
FEIYUE MA ◽  
ZHIYI LIU
Keyword(s):  
Melting Point ◽  
Grain Boundaries ◽  
Microstructural Evolution ◽  
Cast Alloy ◽  
Scanning Calorimetry ◽  
Zr Addition ◽  
Homogenization Time ◽  
The Matrix ◽  
Higher Temperature ◽  
Lower Temperature

The microstructural evolution in an Al - Cu - Mg - Ag alloy with trace Zr addition during homogenization treatment was characterized by Differential Scanning Calorimetry (DSC), Scanning Electron Microscopy (SEM) and Energy-dispersive X-ray Spectroscopy (EDS). It was shown that the low-melting-point phase segregating toward grain boundaries is Al 2 Cu , with a melting point of 523.52°C. A two-step homogenization process was employed to optimize the microstructure of the as-cast alloy, during which the alloy was first homogenized at a lower temperature, then at a higher temperature. After homogenized at 420°C for 6 h, Al 3 Zr particles were finely formed in the matrix. After that, when the alloy was homogenized at an elevated temperature for a longer time, i.e., 515°C for 24 h, most of the precipates at the grain boundaries were removed. Furthermore, the dispersive Al 3 Zr precipitates were retained, without coarsening greatly in the final homogenization step. A kinetics model is employed to predict the optimal homogenization time at a given temperature theoretically, and it confirms the result in present study, which is 420°C/6h+515°C/24h.

scholarly journals Phase Transformations in Cu-Zr Multilayers

1993 ◽  
Vol 311 ◽  
Author(s):  
T.T. Weihs ◽  
T.T. Barbee ◽  
M.M. Wall
Keyword(s):  
Phase Transformations ◽  
Equilibrium Phase ◽  
Scanning Calorimetry ◽  
X Ray ◽  
Multilayer Foils ◽  
Short Range Ordering ◽  
Magnetron Sputter Deposition ◽  
Magnetron Sputter ◽  
Long Range Ordering ◽  
Zr Alloys

ABSTRACTA study of phase transformations is reported for Cu-rich, Cu-Zr multilayer foils that were synthesized using magnetron sputter deposition and annealed using a differential scanning calorimeter. The foils range in composition from 1.6 at% to 9.0 at% Zr and consist of alternate layers of polycrystalline Cu and Zr. Differential scanning calorimetry, X-ray analysis and electron microscopy were used to examine three distinct reactions in the foils: a mixing and an amorphization of the Cu and the Zr, a crystallization to the metastable intermetallic, Cu51Zr14, and a transformation of the Cu51Zr14 phase into the equilibrium phase, Cu9Zr2. The asdeposited layering remained stable during the first two reactions and then broke down in the third reaction as large grains of Cu9Zr2 encompassed the smaller Cu grains. The heats of the reactions and the activation energies of these reactions are measured and are compared to values reported for bulk samples. The measured heats support the observation that amorphous Cu-Zr alloys phase separate and provide evidence that mixing and short range ordering produce 3.5 times more heat than long range ordering when Cu and Zr react and form Cu51Zr14.

scholarly journals A STUDY OF PARAMETERS RELATED TO ANALYSIS OF TRANSITION TEMPERATURES AND ENTHALPIES OF POLYPROPYLENE BY DIFFERENTIAL SCANNING CALORIMETRY (DSC)

2002 ◽  
Vol 10 (11) ◽  
pp. 73-78
Author(s):  
Carlos R. Wolf ◽  
Emir Grave
Keyword(s):  
Differential Scanning Calorimetry ◽  
Material Characterization ◽  
Transition Temperatures ◽  
Nitrogen Flow ◽  
Thermoplastic Polymer ◽  
Scanning Calorimetry ◽  
Know How ◽  
Heating And Cooling ◽  
Polypropylene Material ◽  
Dsc Method

Polypropylene is a thermoplastic polymer, widely employed by converter industries to produce different plastic objects. In order to control and optimize the final properties of the polypropylene material, the evaluation of transition temperatures and enthalpies by Differential Scanning Calorimetry (DSC) has a very important role. Therefore, it is fundamental to know how the analytical conditions influence the results. In this study heating and cooling rates, 10°C/min and 20°C/min, and two different rates of nitrogen flow, 20mL/min and 50mL/min were investigated. It was concluded that thermal properties are influenced by rates of heating and rates of nitrogen flow. The best precision was obtained with the low heating rate, 10°C/min, and high flow rate, 50mL/min. These conditions are being used with the DSC method for polyolefin quality control and material characterization.

Characterization of the Phase Transformations in the Shape Memory Alloy Ni-36 at.% Al

1991 ◽  
Vol 246 ◽  
Author(s):  
J.A. Horton ◽  
E.P. George ◽  
C.J. Sparks ◽  
M.Y. Kao ◽  
O.B. Cavin ◽  
...  
Keyword(s):  
High Temperature ◽  
Shape Memory ◽  
Phase Transformations ◽  
Hot Extrusion ◽  
Exothermic Peak ◽  
Nickel Aluminum ◽  
X Ray Diffraction ◽  
Scanning Calorimetry ◽  
X Ray ◽  
Transmission Electron

AbstractA survey by differential scanning calorimetry (DSC) and recovery during heating of indentations on a series of nickel-aluminum alloys showed that the Ni-36 at.% Al composition has the best potential for a recoverable shape memory effect at temperatures above 100°C. The phase transformations were studied by high temperature transmission electron microscopy (TEM) and by high temperature x-ray diffraction (HTXRD). Quenching from 1200°C resulted in a single phase, fully martensitic structure. The initial quenched-in martensites were found by both TEM and X-ray diffraction to consist of primarily a body centered tetragonal (bct) phase with some body centered orthorhombic (bco) phase present. On the first heating cycle, DSC showed an endothermic peak at 121°C and an exothermic peak at 289°C, and upon cooling a martensite exothermic peak at 115° C. Upon subsequent cycles the 289°C peak disappeared. High temperature X-ray diffraction, with a heating rate of 2°C/min, showed the expected transformation of bct phase to B2 between 100 and 200°C, however the bco phase remained intact. At 400 to 450°C the B2 phase transformed to Ni2Al and Ni5Al3. During TEM heating experiments a dislocation-free martensite transformed reversibly to B2 at temperatures less than 150°C. At higher temperatures (nearly 600°C) 1/3, 1/3, 1/3 reflections from an ω-like phase formed. Upon cooling, the 1/3, 1/3, 1/3 reflections disappeared and a more complicated martensite resulted. Boron additions suppressed intergranular fracture and, as expected, resulted in no ductility improvements. Boron additions and/or hot extrusion encouraged the formation of a superordered bct structure with 1/2, 1/2, 0 reflections.

Thermal Properties Analysis of Several N-Alkanes Eutectic Mixtures Applied in Building Envelopes

2012 ◽  
Vol 512-515 ◽  
pp. 3007-3010
Author(s):  
Jing Yu Huang ◽  
Shi Lei Lv ◽  
Chen Xi Zhang ◽  
Zhi Wei Wang
Keyword(s):  
Thermal Properties ◽  
Melting Temperature ◽  
Latent Heat ◽  
Heat Storage ◽  
Eutectic Mixture ◽  
Scanning Calorimetry ◽  
Latent Heat Storage ◽  
Building Envelopes ◽  
Eutectic Mixtures ◽  
Change Material

This study focuses on the preparation, thermal properties of alkanes eutectic mixtures (n-Octadecane/n-Eicosane, n-Octadecane/n-Docosane and n-Heptadecane /n-Eicosane) as candidate phase change material (PCM) for low temperature latent heat storage systems in building envelopes. Their melting temperature and latent heat were tested by Differential scanning calorimetry (DSC). The testing values were closed to calculation values of accepted theory that ensured the reliability of those datas. The results indicated n-Octadecane/n-Docosane eutectic mixture was more promising PCM for buildings in terms of melting temperature (25.3°C) and latent heat values of melting (158.2J/g).

Effect of Heat Treatment on the Properties of (Fe0.6Co0.4)71Si5Nb4B20 Bulk Metallic Glass

2021 ◽  
Vol 875 ◽  
pp. 70-75
Author(s):  
Syed Zameer Abbas ◽  
Rashid Ali ◽  
Syed Muttahir Shah ◽  
Owais Jan ◽  
Munim Awan
Keyword(s):  
Glass Transition ◽  
Metallic Glass ◽  
Bulk Metallic Glass ◽  
Cast Alloy ◽  
Amorphous Structure ◽  
Indentation Hardness ◽  
Alloy Sample ◽  
Scanning Calorimetry ◽  
Heat Treated Sample ◽  
Heat Treated

Bulk metallic glasses (BMGs) are an important class of materials with unique set of properties. A bulk metallic glass with composition of (Fe0.6Co0.4)71Nb4Si5B20 was cast in the form of a 1 mm thick strip in a water cooled copper mold. The BMG produced was characterized for structure, thermal and mechanical properties. The X-ray diffraction performed on the as cast alloy has shown completely amorphous structure. The glass transition and crystallization peak temperatures obtained through differential scanning calorimetry scan were 542 °C and 588.4 °C, respectively. Some cast amorphous alloy sample was annealed below glass transition (450 °C for 30 mi93nutes) and others above glass transition (580 °C for 5 minutes) temperatures. Nano- indentation hardness of 13.3 GPa was obtained for as cast alloy while a hardness values of 12.8 and 15.84 GPa were measured for heat treated alloys at temperature of 450 °C and 580 °C, respectively. Increase in hardness was attributed to formation of crystals in an amorphous matrix whereas decrease in hardness was due to relaxation of quenching residual stresses. The maximum value of elastic modulus obtained through indentation was 255 GPa for 580 °C heat treated sample.

Wear Properties of Thixoformed Al-5.7Si-2Cu-0.3Mg Aluminium Alloy

2019 ◽  
Vol 285 ◽  
pp. 63-68 ◽  
Author(s):  
Mnel A. Abdelgnei ◽  
M. Zaidi Omar ◽  
Mariyam Jameelah Ghazali
Keyword(s):  
Aluminium Alloy ◽  
Cast Alloy ◽  
Wear Test ◽  
Wear Behaviour ◽  
Dry Sliding Wear ◽  
Dry Sliding ◽  
Wear Properties ◽  
Scanning Calorimetry ◽  
Delamination Wear ◽  
Sliding Distance

Earlier work has shown that Al-5.7Si-2Cu-0.3Mg aluminium alloy is suitable for thixoforming process. Here, the dry sliding wear behaviour of the alloy, in the as-cast and thixoformed conditions were investigated. The cooling slope technique was used to produce the alloy with globular microstructure for the thixoforming process. Both the thixoformed and cast samples were subjected to T6 heat treatments prior to the wear tests. The tests were carried out using a pin-on-disc tribometer, against a hardened M2 tool steel disc of 62 HRC at different loads, under dry sliding conditions at fixed sliding speed and sliding distance of 1 m.s–1 and 5 km respectively. The microstructural response, worn surfaces were thoroughly and carefully examined using various methods such as scanning electron microscopy, energy dispersive spectroscopy, and differential scanning calorimetry. The density of the heat treated thixoformed alloys showed significant increase in the hardness property, among others, due to its reduced porosity. Their wear test results also observed that the weight loss of materials increase with an increase in the input load and the sliding distance for all samples. However, the as-cast alloy displayed higher wear rate compared with the thixoformed alloys. In general, the wear mechanisms showed a mixture of abrasive, oxidative and delamination wear (mild wear) at low applied loads and mainly an adhesive (severe wear) at high applied loads.

Sign in / Sign up

Export Citation Format

Share Document