Heat transfer characteristics of parallel and counter flow micro-channel heat exchangers with varying wall resistance

2011 ◽  
Vol 11 (5) ◽  
pp. 318 ◽  
Author(s):  
A.M. Maqableh ◽  
A.F. Khadrawi ◽  
M.A. Al Nimr ◽  
S.A. Ammourah ◽  
A.C. Benim
Keyword(s):  
Heat Transfer ◽  
Heat Exchangers ◽  
Micro Channel ◽  
Heat Transfer Characteristics ◽  
Counter Flow ◽  
Transfer Characteristics

Effect of the Chevron Angle on Cooling Heat Transfer Characteristics of Supercritical Pressure Fluids in Plate Heat Exchangers

2018 ◽  
Vol 40 (12) ◽  
pp. 1007-1022 ◽  
Author(s):  
Kazushi Miyata ◽  
Hideo Mori ◽  
Takahiro Taniguchi ◽  
Shuichi Umezawa ◽  
Katsuhiko Sugita
Keyword(s):  
Heat Transfer ◽  
Heat Exchangers ◽  
Supercritical Pressure ◽  
Heat Transfer Characteristics ◽  
Plate Heat ◽  
Transfer Characteristics

Pressure Drop and Heat Transfer Characteristics of Louvered Fin Heat Exchangers

2013 ◽  
Vol 465-466 ◽  
pp. 500-504 ◽  
Author(s):  
Shahrin Hisham Amirnordin ◽  
Hissein Didane Djamal ◽  
Mohd Norani Mansor ◽  
Amir Khalid ◽  
Md Seri Suzairin ◽  
...  
Keyword(s):  
Heat Transfer ◽  
Pressure Drop ◽  
Heat Transfer Rate ◽  
Heat Exchangers ◽  
Transfer Rate ◽  
Three Dimensional ◽  
Considerable Effect ◽  
Heat Transfer Characteristics ◽  
Transfer Characteristics ◽  
Louvered Fin

This paper presents the effect of the changes in fin geometry on pressure drop and heat transfer characteristics of louvered fin heat exchanger numerically. Three dimensional simulation using ANSYS Fluent have been conducted for six different configurations at Reynolds number ranging from 200 to 1000 based on louver pitch. The performance of this system has been evaluated by calculating pressure drop and heat transfer coefficient. The result shows that, the fin pitch and the louver pitch have a very considerable effect on pressure drop as well as heat transfer rate. It is observed that increasing the fin pitch will relatively result in an increase in heat transfer rate but at the same time, the pressure drop will decrease. On the other hand, low pressure drop and low heat transfer rate will be obtained when the louver pitch is increased. Final result shows a good agreement between experimental and numerical results of the louvered fin which is about 12%. This indicates the capability of louvered fin in enhancing the performance of heat exchangers.

Numerical Investigation of Heat Transfer Characteristics of Different Nanoparticles Using Modified Eulerian-Eulerian Model

2020 ◽  
Author(s):  
Muzafar Hussain ◽  
Shahbaz Tahir
Keyword(s):  
Heat Transfer ◽  
Experimental Data ◽  
Heat Exchangers ◽  
Single Phase ◽  
Reynolds Numbers ◽  
Operating Conditions ◽  
Phase Model ◽  
Heat Transfer Characteristics ◽  
Eulerian Model ◽  
Transfer Characteristics

Abstract Nanofluids are widely adopted nowadays to enhance the heat transfer characteristics in the solar applications because of their excellent thermophysical properties. In this paper, a modified Eulerian-Eulerian model recently developed based on experiments was validated numerically to account for the deviations from the experimental data. The modified Eulerian-Eulerian model is compared with the single-phase model, Eulerian-Eulerian models for TiO2-water at different operating conditions and deviation from the experimental data for each of the model was documented. However, the modified Eulerian-Eulerian model gave much closer results when compared to the experimental data. For the further extension of work, the modified Eulerian-Eulerian model was applied to different nanofluids in order to investigate their heat transfer characteristics. Three different nanoparticles were investigated namely Cu, MgO, and Ag and their heat transfer characteristics is calculated based on the modified Eulerian-Eulerian model as well as the single-phase model for the comparison. For lower values of Reynolds numbers, the average heat transfer coefficient was almost identical for both models with small percentage of error but for higher Reynolds numbers, the deviation got larger. Therefore, single-phase model is not appropriate for higher Reynolds numbers and modified Eulerian-Eulerian model should be used to accurately predict the heat transfer characteristics of the nanofluids at higher Reynolds numbers. From the analysis it is found that the Ag-water nanofluid have the highest heat transfer characteristics among others and can be employed in the solar heat exchangers to enhance the heat transfer characteristics and to further improve the efficiency.

Sign in / Sign up

Export Citation Format

Share Document