Investigation of machining rate and roughness for rotary ultrasonic drilling of Inconel 718 alloy with slotted diamond metal bonded tool

2018 ◽  
Vol 13 (1) ◽  
pp. 68 ◽  
Author(s):  
Dipesh Popli ◽  
Meenu Gupta
Keyword(s):  
Inconel 718 ◽  
Inconel 718 Alloy ◽  
Ultrasonic Drilling ◽  
Machining Rate ◽  
Rotary Ultrasonic Drilling

scholarly journals A Comparative Analysis of Laser Additive Manufacturing of High Layer Thickness Pure Ti and Inconel 718 Alloy Materials Using Finite Element Method

Materials ◽  
2021 ◽  
Vol 14 (4) ◽  
pp. 876 ◽  
Author(s):  
Sapam Ningthemba Singh ◽  
Sohini Chowdhury ◽  
Yadaiah Nirsanametla ◽  
Anil Kumar Deepati ◽  
Chander Prakash ◽  
...  
Keyword(s):  
Finite Element Method ◽  
Finite Element ◽  
Layer Thickness ◽  
Inconel 718 ◽  
Laser Power ◽  
Scanning Speed ◽  
Laser Additive Manufacturing ◽  
Inconel 718 Alloy ◽  
Melt Pool ◽  
High Layer

Investigation of the selective laser melting (SLM) process, using finite element method, to understand the influences of laser power and scanning speed on the heat flow and melt-pool dimensions is a challenging task. Most of the existing studies are focused on the study of thin layer thickness and comparative study of same materials under different manufacturing conditions. The present work is focused on comparative analysis of thermal cycles and complex melt-pool behavior of a high layer thickness multi-layer laser additive manufacturing (LAM) of pure Titanium (Ti) and Inconel 718. A transient 3D finite-element model is developed to perform a quantitative comparative study on two materials to examine the temperature distribution and disparities in melt-pool behaviours under similar processing conditions. It is observed that the layers are properly melted and sintered for the considered process parameters. The temperature and melt-pool increases as laser power move in the same layer and when new layers are added. The same is observed when the laser power increases, and opposite is observed for increasing scanning speed while keeping other parameters constant. It is also found that Inconel 718 alloy has a higher maximum temperature than Ti material for the same process parameter and hence higher melt-pool dimensions.

Corrosion Behavior of a Selective Laser Melted Inconel 718 Alloy in a 3.5 wt.% NaCl Solution

2021 ◽  
Author(s):  
Yanbing Tang ◽  
Xinwang Shen ◽  
Yanxin Qiao ◽  
Lanlan Yang ◽  
Jian Chen ◽  
...  
Keyword(s):  
Corrosion Behavior ◽  
Inconel 718 ◽  
Nacl Solution ◽  
Inconel 718 Alloy

scholarly journals Very-High-Cycle Fatigue Behavior of Inconel 718 Alloy Fabricated by Selective Laser Melting at Elevated Temperature

Materials ◽  
2021 ◽  
Vol 14 (4) ◽  
pp. 1001
Author(s):  
Zongxian Song ◽  
Wenbin Gao ◽  
Dongpo Wang ◽  
Zhisheng Wu ◽  
Meifang Yan ◽  
...  
Keyword(s):  
Elevated Temperature ◽  
Selective Laser Melting ◽  
Fatigue Resistance ◽  
Inconel 718 ◽  
High Cycle Fatigue ◽  
Cycle Fatigue ◽  
Laser Melting ◽  
Inconel 718 Alloy ◽  
Very High Cycle Fatigue ◽  
Very High

This study investigates the very-high-cycle fatigue (VHCF) behavior at elevated temperature (650 °C) of the Inconel 718 alloy fabricated by selective laser melting (SLM). The results are compared with those of the wrought alloy. Large columnar grain with a cellular structure in the grain interior and Laves/δ phases precipitated along the grain boundaries were exhibited in the SLM alloy, while fine equiaxed grains were present in the wrought alloy. The elevated temperature had a minor effect on the fatigue resistance in the regime below 108 cycles for the SLM alloy but significantly reduced the fatigue strength in the VHCF regime above 108 cycles. Both the SLM and wrought specimens exhibited similar fatigue resistance in the fatigue life regime of fewer than 107–108 cycles at elevated temperature, and the surface initiation mechanism was dominant in both alloys. In a VHCF regime above 107–108 cycles at elevated temperature, the wrought material exhibited slightly better fatigue resistance than the SLM alloy. All fatigue cracks are initiated from the internal defects or the microstructure discontinuities. The precipitation of Laves and δ phases is examined after fatigue tests at high temperatures, and the effect of microstructure on the formation and the propagation of the microstructural small cracks is also discussed.

Microstructure and Wear Properties of Laser-clad NiCo Alloy Coating on Inconel 718 Alloy

2021 ◽  
pp. 160412
Author(s):  
Tao Wang ◽  
Chao Wang ◽  
Juanjuan Li ◽  
Linjiang Chai ◽  
Xing Hu ◽  
...  
Keyword(s):  
Inconel 718 ◽  
Alloy Coating ◽  
Wear Properties ◽  
Inconel 718 Alloy

Precipitation of γ″ in Inconel 718 alloy from microstructure to mechanical properties.

Materialia ◽  
2021 ◽  
pp. 101187
Author(s):  
Alexandre Balan ◽  
Michel Perez ◽  
Thibaut Chaise ◽  
Sophie Cazottes ◽  
Didier Bardel ◽  
...  
Keyword(s):  
Mechanical Properties ◽  
Inconel 718 ◽  
Inconel 718 Alloy
Sign in / Sign up

Export Citation Format

Share Document