The influence law of cooling rate on microstructure and properties of low-carbon high-grade AF pipeline steel

2016 ◽  
Vol 11 (5) ◽  
pp. 373 ◽  
Author(s):  
Yongli Chen ◽  
Xuejiao Zhou ◽  
Yueyue Jiang ◽  
Qingxia Wang
Keyword(s):  
Cooling Rate ◽  
Pipeline Steel ◽  
High Grade ◽  
Low Carbon ◽  
Microstructure And Properties

scholarly journals Continuous Cooling Transformation Diagram, Microstructures, and Properties of the Simulated Coarse-Grain Heat-Affected Zone in a Low-Carbon Bainite E550 Steel

Metals ◽  
2019 ◽  
Vol 9 (9) ◽  
pp. 939 ◽  
Author(s):  
Yun Zong ◽  
Chun-Ming Liu
Keyword(s):  
Impact Toughness ◽  
Cooling Rate ◽  
Vickers Hardness ◽  
Heat Affected Zone ◽  
Granular Bainite ◽  
Coarse Grain ◽  
Low Carbon ◽  
Transformation Diagram ◽  
Lath Bainite ◽  
Continuous Cooling Transformation Diagram

In order to provide important guidance for controlling and obtaining the optimal microstructures and mechanical properties of a welded joint, the continuous cooling transformation diagram of a new low-carbon Nb-microalloyed bainite E550 steel in a simulated coarse-grain heat-affected zone (CGHAZ) has been constructed by thermal dilatation method in this paper. The welding thermal simulation experiments were conducted on a Gleeble-3800 thermo-mechanical simulator. The corresponding microstructure was observed by a LEICA DM2700M. The Vickers hardness (HV) and the impact toughness at −40 °C were measured according to the ASTM E384 standard and the ASTM E2298 standard, respectively. The experimental results may indicate that the intermediate temperature phase transformation of the whole bainite can occur in a wide range of cooling rates of 2–20 °C/s. In the scope of cooling rates 2–20 °C/s, the microstructure of the heat-affected zone (HAZ) mainly consists of lath bainite and granular bainite. Moreover, the proportion of lath bainite increased and granular bainite decreased as the cooling rate increasing. There is a spot of lath martensite in the microstructure of HAZ when the cooling rate is above 20 °C/s. The Vickers hardness increases gradually with the increasing of the cooling rate, and the maximum hardness is 323 HV10. When the cooling time from 800 °C to 500 °C (t8/5) is 5–15 s, it presents excellent −40 °C impact toughness (273–286 J) of the CGHAZ beyond the base material (163 J).

scholarly journals A Comparative Study of Acicular Ferrite Transformation Behavior between Surface and Interior in a Low C–Mn Steel by HT-LSCM

Metals ◽  
2021 ◽  
Vol 11 (5) ◽  
pp. 699
Author(s):  
Xiaojin Liu ◽  
Guo Yuan ◽  
Raja. Devesh Kumar Misra ◽  
Guodong Wang
Keyword(s):  
Grain Boundaries ◽  
Cooling Rate ◽  
Acicular Ferrite ◽  
Laser Scanning ◽  
Sample Surface ◽  
Surface Microstructure ◽  
In Situ Observation ◽  
Low Carbon ◽  
Transformation Behavior ◽  
Ferrite Transformation

In this study, the acicular ferrite transformation behavior of a Ti–Ca deoxidized low carbon steel was studied using a high-temperature laser scanning confocal microscopy (HT-LSCM). The in situ observation of the transformation behavior on the sample surface with different cooling rates was achieved by HT-LSCM. The microstructure between the surface and interior of the HT-LSCM sample was compared. The results showed that Ti–Ca oxide particles were effective sites for acicular ferrite (AF) nucleation. The start transformation temperature at grain boundaries and intragranular particles decreased with an increase in cooling rate, but the AF nucleation rate increased and the surface microstructure was more interlocked. The sample surface microstructure obtained at 3 °C/s was dominated by ferrite side plates, while the ferrite nucleating sites transferred from grain boundaries to intragranular particles when the cooling rate was 15 °C/s. Moreover, it was interesting that the microstructure and microhardness of the sample surface and interior were different. The AF dominating microstructure, obtained in the sample interior, was much finer than the sample surface, and the microhardness of the sample surface was much lower than the sample interior. The combined factors led to a coarse size of AF on the sample surface. AF formed at a higher temperature resulted in the coarse size. The available particles for AF nucleation on the sample surface were quite limited, such that hard impingement between AF plates was much weaker than that in the sample interior. In addition, the transformation stress in austenite on the sample surface could be largely released, which contributed to a coarser AF plate size. The coarse grain size, low dislocation concentration and low carbon content led to lower hardness on the sample surface.

Effect of Cooling Rate on Microstructure and Properties of Heat-Treated Fe3Al Intermetallics

2011 ◽  
Vol 189-193 ◽  
pp. 3891-3894
Author(s):  
Ya Min Li ◽  
Hong Jun Liu ◽  
Yuan Hao
Keyword(s):  
Heat Treatment ◽  
Cooling Rate ◽  
Lattice Distortion ◽  
Annealing Furnace ◽  
Microstructure And Properties ◽  
Homogenizing Annealing ◽  
Heat Treated ◽  
Mixed Fracture ◽  
Sand Mould ◽  
The Impact

The casting Fe3Al intermetallics were solidified in sodium silicate sand mould and permanent mould respectively to get different cooling rates. After heat treatment (1000°С/15 h homogenizing annealing + furnace cooling followed by 600°С/1 h tempering + oil quenching), the microstructure and properties of Fe3Al intermetallics were investigated. The results show that the heat-treated Fe3Al intermetallics at higher cooling rate has finer grained microstructure than lower cooling rate, and the lattice distortion increases due to the higher solid solubility of the elements Cr and B at higher cooling rate. The tensile strength and hardness of the Fe3Al intermetallics at higher cooling rate are slightly higher also. However, the impact power of intermetallics at higher cooling rate is 67.5% higher than that at lower cooling rate, and the impact fracture mode is also transformed from intercrystalline fracture at lower cooling rate to intercrystallin+transcrystalline mixed fracture at higher cooling rate.

Microstructure and Properties of a Non-Quenched Prehardened Steel at Different Cooling Rate

2012 ◽  
Vol 524-527 ◽  
pp. 1976-1979
Author(s):  
Yi Luo ◽  
Jin Ming Peng
Keyword(s):  
Mechanical Properties ◽  
Fine Structure ◽  
Optical Microscopy ◽  
Cooling Rate ◽  
Retained Austenite ◽  
Transformation Products ◽  
Electronic Microscopy ◽  
Transmission Electronic Microscopy ◽  
Microstructure And Properties ◽  
Cooling Conditions

Mechanical properties of non-quenched prehardened (NQP) steel air cooled and sand cooled after forged were tested and their microstructure was investigated by optical microscopy and transmission electronic microscopy(TEM). The results show that mechanical properties of the NQP steel are similar at both cooling conditions, and their microstructure is bainite, whose fine structure is main bainite ferrite laths, retained austenite films, retained austenite islands and their transformation products. Bainite ferrite laths of the NQP steel air cooled are narrower than that sand cooled, while more retained austenite islands exist in latter.

Effect of cooling rate on the structure and properties of low-carbon tube steel

Metallurgist ◽  
2008 ◽  
Vol 52 (7-8) ◽  
pp. 464-469 ◽  
Author(s):  
I. Yu. Pyshmintsev ◽  
A. N. Boryakova ◽  
M. A. Smirnov
Keyword(s):  
Cooling Rate ◽  
Tube Steel ◽  
Structure And Properties ◽  
Low Carbon ◽  
Carbon Tube

scholarly journals Strain Aging Behavior of Microalloyed Low Carbon Seamless Pipeline Steel

2016 ◽  
Vol 56 (1) ◽  
pp. 126-131 ◽  
Author(s):  
Qianlin Wu ◽  
Zhonghua Zhang ◽  
Yaoheng Liu
Keyword(s):  
Strain Aging ◽  
Pipeline Steel ◽  
Low Carbon ◽  
Aging Behavior

The Development of Large Diameter and Thickness X80 HSAW Linepipe

2008 ◽  
Author(s):  
Weiwei Li ◽  
Chunyong Huo ◽  
Qiurong Ma ◽  
Yaorong Feng
Keyword(s):  
Bauschinger Effect ◽  
Pipeline Steel ◽  
Large Diameter ◽  
Base Material ◽  
Longitudinal Direction ◽  
Strength Loss ◽  
Ring Test ◽  
Low Carbon ◽  
Pipeline Project ◽  
Submerged Arc

For the requirement of 2nd West-East Pipeline Project of China, X80 large diameter & thickness linepipe with helical seam submerged arc welded (HSAW) were developed, with 1219 mm OD and 18.4 mm WT. Acicular ferrite type and super-low carbon, high Niobium chemical composition pipeline steel was adopted for the base material. The very stringent requirements at −10 °C for toughness, i.e. 220J/170J for average/minimum for pipe body and 80J/60J for average/minimum for weld and HAZ were meet successfully. The yield strength loss due to Bauschinger effect was found lower than 20MPa, which benefited. The very low residual stress level was testified by cut-ring test which cuts a section pipe about exceed 100mm long, and then cut the section apart from welds 100mm along the longitudinal direction.

Sign in / Sign up

Export Citation Format

Share Document