scholarly journals Effect of process parameters on cutting speed of wire EDM process in machining HSLA steel with cryogenic treated brass wire

2019 ◽  
Vol 14 (2) ◽  
pp. 143-152 ◽  
Author(s):  
W. Tahir ◽  
M. Jahanzaib ◽  
A. Raza
Keyword(s):  
Process Parameters ◽  
Hsla Steel ◽  
Cutting Speed ◽  
Wire Edm ◽  
Edm Process ◽  
Brass Wire

Multi-Response Optimization of Wire-EDM Process Parameters of Titanium Alloy Using Taguchi Method and Grey Relational Analysis

2015 ◽  
Vol 772 ◽  
pp. 245-249
Author(s):  
A. Ramamurthy ◽  
R. Sivaramakrishnan ◽  
S. Venugopal ◽  
T. Muthuramalingam
Keyword(s):  
Titanium Alloy ◽  
Process Parameters ◽  
Grey Relational Analysis ◽  
Wire Edm ◽  
Relational Analysis ◽  
Response Optimization ◽  
Grey Relational ◽  
Pulse On Time ◽  
Pulse Off Time ◽  
Edm Process

It is very important and complexity to find the optimum values of wire EDM process parameters and contribution of each parameter to attain the better performance characteristics. In this study, an attempt has been made to optimize those parameters while machining the titanium alloy. Since the process involves more one than one response parameter, it is essential to carry out the multi-response optimization methodology .The experiments have been conducted with different levels of input factors such as pulse on time,pulse off time and wire tension based on Taguchi L9 orthogonal table.Wire EDM optimal process parameter has been identified using grey relational analysis and significant parameter has been determined by analysis of variance. Experimental results have indicated that the multi-response characteristic such as material removal rate and surface roughness can be improved effectively through grey relational analysis.

scholarly journals Study of wire-electrical discharge machining parameters of titanium alloy by using taguchi method

2018 ◽  
Vol 7 (2.8) ◽  
pp. 10
Author(s):  
A VS Ram Prasad ◽  
Koona Ramji ◽  
B Raghu Kumar
Keyword(s):  
Surface Roughness ◽  
Taguchi Method ◽  
Process Parameters ◽  
Optimization Technique ◽  
Machining Process ◽  
Machining Parameters ◽  
Wire Edm ◽  
Pulse On Time ◽  
Pulse Off Time ◽  
Edm Process

Machining of Titanium alloys is difficult due to their chemical and physical properties namely excellent strength, chemical reactivity and low thermal conductivity. Traditional machining of such materials leads to formation of continuous chips and tool bits are subjected to chatter which leads to formation of poor surface on machined surface. In this study, Wire-EDM one of the most popular unconventional machining process which was used to machine such difficult-to-cut materials. Effect of Wire-EDM process parameters namely peak current, pulse-on- time, pulse-off-time, servo voltage on MRRand SR was investigated by Taguchi method. 0.25 mm brass wire was used in this process as electrode material. A surface roughness tester (Surftest 301) was used to measure surface roughness value of the machined work surface. A multi-response optimization technique was then utilized to optimize Wire-EDM process parameters for achieving maximum MRR and minimum SR simultaneously.

Developments in Wire-EDM for the Manufacturing of Fir Tree Slots in Turbine Discs Made of Inconel 718

2012 ◽  
Vol 504-506 ◽  
pp. 1177-1182 ◽  
Author(s):  
Fritz Klocke ◽  
David Welling ◽  
Jens Dieckmann ◽  
Drazen Veselovac ◽  
Roberto Perez
Keyword(s):  
Cross Section ◽  
Manufacturing Processes ◽  
Wire Edm ◽  
Safety Requirements ◽  
Critical Components ◽  
The One ◽  
Non Destructive ◽  
Edm Process ◽  
Brass Wire ◽  
Tree Production

This paper deals with developments of Wire-EDM technologies for fir tree slot production. The aim of these developments is to substitute certain conventional processes within turbine manufacturing that have been identified as non-optimal like the critical broaching process. Thereby the negative characteristics like inflexible manufacturing processes, high machine tool investment costs and huge energy consumption can be abolished. The objective targets of the conducted research are to meet all safety requirements of the critical components and get an economic manufacturing process. In the first step a special brass wire technology for cutting Ni-based super alloys was developed. Main focus was to meet the requirements of fir tree production concerning aspects of surface integrity and geometry. To measure these aspects on the one hand non-destructive analyses have been performed to guarantee surface roughness and accuracy. On the other hand destructive analyses in terms of cross section polishing for showing thermal influenced rim zones have been prepared. A capable Wire-EDM process is presented.

Sign in / Sign up

Export Citation Format

Share Document