scholarly journals Experimental Investigation and Development of Multi Response ANN Modeling in Turning Al-SiCp MMC using Polycrystalline Diamond Tool

2013 ◽  
Vol 2 (2) ◽  
pp. 1-8 ◽  
Author(s):  
Santosh Tamang ◽  
◽  
M. Chandrasekaran
Keyword(s):  
Experimental Investigation ◽  
Diamond Tool ◽  
Polycrystalline Diamond ◽  
Ann Modeling

Small Holes Fabrication on Soda Glass by Self-Elastic Polycrystalline Diamond Tool

2012 ◽  
Vol 516 ◽  
pp. 516-521
Author(s):  
Chung Chieh Cheng ◽  
Dong Yea Sheu
Keyword(s):  
Surface Roughness ◽  
Diamond Tool ◽  
Polycrystalline Diamond ◽  
The Self ◽  
High Quality ◽  
Drilling Tool ◽  
Drilling Tools ◽  
Absorbing Materials ◽  
New Type ◽  
Small Holes

This study describes a novel process to drill small holes in brittle materials such as glass, silicon and ceramic using a self-elastic polycrystalline diamond (PCD) drilling tool. In order to improve the surface roughness and reduce crack of the small holes, a new type of self-elastic PCD drilling tool equipped with vibration absorbing materials inside the housing was developed to fabricate small holes in glass in this study. The self-elastic PCD drilling tools could absorb the mechanical force by the vibration absorbing materials while the PCD tool penetrates into the small holes. Compared to conventional PCD drilling tools, the experimental results show that high-quality small holes drilled in glass can be achieved with cracking as small as 0.02mm on the outlet surface using the self-elastic PCD drilling tool.

A Truing Technique of Flattening Diamond Grains for Fabricating Microstructures with Fine Surfaces

2008 ◽  
Vol 389-390 ◽  
pp. 350-355
Author(s):  
Takeshi Harada ◽  
Takuya Semba
Keyword(s):  
Surface Roughness ◽  
Electrical Discharge ◽  
Diamond Tool ◽  
Electrical Discharge Machining ◽  
Polycrystalline Diamond ◽  
Mesh Size ◽  
Diamond Disk ◽  
Working Surface ◽  
Work Material ◽  
Tool Profile

A truing technique that can be used to shape the tip of an electroformed diamond tool into a hemisphere and flatten diamond grains on the tool working surface at the same level as the bond face was developed. A polycrystalline diamond disk whose top surface roughened by electrical discharge machining was partially flattened by grinding was used as a truer. Diamond grains on the tool working surface were successfully flattened along the hemispherical tool profile when the grains mesh size of #1000 was employed. In addition, a grinding test using glasslike carbon as a work material revealed that a surface roughness of less than 50 nm Rz could be obtained in both cases when moving the tool on contour and scanning paths.

Surface quality of carbon/carbon composite after ultrasonic assisted turning

2011 ◽  
Vol 225 (11) ◽  
pp. 2144-2148 ◽  
Author(s):  
F J Ma ◽  
D M Guo ◽  
R K Kang ◽  
Y J Ren
Keyword(s):  
Surface Quality ◽  
Evaluation Method ◽  
Diamond Tool ◽  
Polycrystalline Diamond ◽  
Carbon Composite ◽  
Distribution Characteristics ◽  
Good Surface ◽  
Ultrasonic Assisted ◽  
Machining Defect

It is usually hard to obtain a good surface quality of carbon/carbon (C/C) composite by turning due to its non-homogeneity and anisotropy. Contrasting experiments of ultrasonic assisted turning (UAT) and common turning (CT) of the C/C composite were carried out using a polycrystalline diamond tool. The cylindrical surface of the turning was classified into four typical types based on different fibre orientations. The influence of fibre distribution characteristics on surface roughness was analysed by measuring and comparing the roughness of these surfaces, and an evaluation method of surface quality for the C/C composite after turning was established. The results of UAT experiments on the C/C composite show that UAT could effectively reduce the machining defect. The roughness of typical surfaces 1 and 2 machined using UAT was about 20 per cent lower than that using CT.

Influence of Tungsten-Carbide and Cobalt on Tool Wear in Cutting of Cemented Carbides with Polycrystalline Diamond Tool

2013 ◽  
Vol 7 (4) ◽  
pp. 433-438 ◽  
Author(s):  
Junsuke Fujiwara ◽  
◽  
Keisuke Wakao ◽  
Takeshi Miyamoto ◽  
Keyword(s):  
Particle Size ◽  
Tool Wear ◽  
Tungsten Carbide ◽  
Diamond Tool ◽  
Polycrystalline Diamond ◽  
Cemented Carbides ◽  
Large Particles

The influence of the tungsten-carbide (WC) particle size and Co contents of cemented carbides on polycrystalline diamond tool wear during turning was investigated experimentally. The main results obtained were as follows. (1) Tool wear increased with increasing Co content. (2) It is important to cut off the binder between the WC particles and the Co. (3) Cemented carbides containing small WC particles are more effective than cemented carbides containing large particles.

Sign in / Sign up

Export Citation Format

Share Document