scholarly journals High-performance Full-atomistic Simulation of Optical Thin Films

2018 ◽  
Vol 5 (3) ◽  
Keyword(s):  
Thin Films ◽  
Atomistic Simulation ◽  
High Performance

scholarly journals High performance, electroforming-free, thin film memristors using ionic Na0.5Bi0.5TiO3

2021 ◽  
Vol 9 (13) ◽  
pp. 4522-4531
Author(s):  
Chao Yun ◽  
Matthew Webb ◽  
Weiwei Li ◽  
Rui Wu ◽  
Ming Xiao ◽  
...  
Keyword(s):  
Thin Film ◽  
Thin Films ◽  
Resistive Switching ◽  
Growth Temperature ◽  
High Performance ◽  
20 Nm

Interfacial resistive switching and composition-tunable RLRS are realized in ionically conducting Na0.5Bi0.5TiO3 thin films, allowing optimised ON/OFF ratio (>104) to be achieved with low growth temperature (600 °C) and low thickness (<20 nm).

In-situ growth of high-performance (Ag, Sn) co-doped CoSb3 thermoelectric thin films

2021 ◽  
Author(s):  
Zhuang-Hao Zheng ◽  
Jun-Yun Niu ◽  
Dong-Wei Ao ◽  
Bushra Jabar ◽  
Xiao-Lei Shi ◽  
...  
Keyword(s):  
Thin Films ◽  
High Performance ◽  
In Situ Growth ◽  
Thermoelectric Thin Films ◽  
Co Doped

Depositing High-Performance Conductive Thin Films by Using Atomic Layer Deposition

2015 ◽  
Vol 764-765 ◽  
pp. 138-142 ◽  
Author(s):  
Fa Ta Tsai ◽  
Hsi Ting Hou ◽  
Ching Kong Chao ◽  
Rwei Ching Chang
Keyword(s):  
Thin Films ◽  
Atomic Layer Deposition ◽  
High Performance ◽  
Atomic Layer ◽  
Electric Properties ◽  
X Ray Diffraction ◽  
Layer Deposition ◽  
Azo Thin Film ◽  
Aluminum Doped Zinc Oxide ◽  
Conductive Thin Films

This work characterizes the mechanical and opto-electric properties of Aluminum-doped zinc oxide (AZO) thin films deposited by atomic layer deposition (ALD), where various depositing temperature, 100, 125, 150, 175, and 200 °C are considered. The transmittance, microstructure, electric resistivity, adhesion, hardness, and Young’s modulus of the deposited thin films are tested by using spectrophotometer, X-ray diffraction, Hall effect analyzer, micro scratch, and nanoindentation, respectively. The results show that the AZO thin film deposited at 200 °C behaves the best electric properties, where its resistance, Carrier Concentration and mobility reach 4.3×10-4 Ωcm, 2.4×1020 cm-3, and 60.4 cm2V-1s-1, respectively. Furthermore, microstructure of the AZO films deposited by ALD is much better than those deposited by sputtering.

Unveiling the crystalline packing of Y6 in thin films by thermal induced “backbone-on” orientation

2021 ◽  
Author(s):  
Yiqun Xiao ◽  
Jun Yuan ◽  
Guodong Zhou ◽  
Ka Chak Ngan ◽  
Xinxin Xia ◽  
...  
Keyword(s):  
Thin Films ◽  
Solar Cells ◽  
Organic Solar Cells ◽  
High Performance ◽  
Molecular Packing

Researchers are endeavoring to decode the fundamental reasons for the non-fullerene acceptor, Y6, to deliver high-performance organic solar cells. In this manuscript, we tackle this problem from the molecular packing...

scholarly journals Improved Morphology of Poly(3,4-ethylenedioxythiophene):Poly(styrenesulfonate) Thin Films for All-Electrospray-Coated Organic Photovoltaic Cells

2016 ◽  
Vol 2016 ◽  
pp. 1-8 ◽  
Author(s):  
Yingjie Liao ◽  
Takeshi Fukuda ◽  
Norihiko Kamata
Keyword(s):  
Thin Films ◽  
High Performance ◽  
Photovoltaic Cells ◽  
Spray Coating ◽  
Organic Photovoltaic ◽  
Organic Photovoltaic Cells ◽  
Ambient Conditions ◽  
Deposition Parameters ◽  
Coating Methods ◽  
Organic Devices

Spray coating technique has been established as a promising substitute for the traditional coating methods in the fabrication of organic devices in many reports recently. Control of film morphology at the microscopic scale is critical if spray-coated devices are to achieve high performance. Here we investigate electrospray deposition protocols for the fabrication of poly(3,4-ethylenedioxythiophene):poly(styrenesulfonate) (PEDOT:PSS) thin films with a single additive system under ambient conditions at room temperature. Critical deposition parameters including solution composition, applied voltage, and relative humidity are discussed systematically. Optimized process for preparing homogenous PEDOT:PSS thin films is applied to all-electrospray-coated organic photovoltaic cells and contributes to a power conversion efficiency comparable to that of the corresponding all-spin-coated device.

Sign in / Sign up

Export Citation Format

Share Document