scholarly journals Determination of Shaft Rotation Angle from Accelerations of the Wireless Sensor by the Novel Numerical Method

2018 ◽  
Vol 18 (3) ◽  
pp. 143-149
Author(s):  
V.V. Sinitsin ◽  
N.M. Yaparova
Keyword(s):  
Numerical Method ◽  
Rotation Angle ◽  
Wireless Sensor ◽  
The Novel ◽  
Shaft Rotation ◽  
Shaft Rotation Angle

scholarly journals Influence of Water and Mineral Oil on the Leaks in Satellite Motor Commutation Unit Clearances

2017 ◽  
Vol 24 (3) ◽  
pp. 58-67 ◽  
Author(s):  
Paweł Śliwiński
Keyword(s):  
Rotation Angle ◽  
Mineral Oil ◽  
Fluid Viscosity ◽  
Working Chamber ◽  
Shaft Rotation ◽  
Influence Of Water ◽  
Mathematical Formulas ◽  
Working Media ◽  
Shaft Rotation Angle ◽  
Geometrical Dimensions

Abstract The article describes the flow rates of mineral oil and water flowing, as working media, through the commutation unit of a hydraulic satellite motor. It is demonstrated that geometrical dimensions of commutation unit clearances change as a function of the machine shaft rotation angle. Methods for measuring the rate of this flow and the pressure in the working chamber are presented. The results of pressure measurements in the working chamber during the transition from the filling cycle to the emptying cycle are included. The pressure in the motor’s working chamber changes linearly as a function of the shaft rotation angle, which has a significant effect on the leakage in the commutation unit clearances. The paper presents new mathematical formulas in the form: Q=f(Δpγ) to calculate the flow rate of water and mineral oil in the commutation unit clearances. The γ factor is described as a function of fluid viscosity and clearance length (the motor shaft rotation angle). The coefficients used in these formulas were determined based on the results of laboratory tests of a motor supplied with water and mineral oil.

A novel method for the determination of linting propensity of paper

TAPPI Journal ◽  
2012 ◽  
Vol 11 (10) ◽  
pp. 9-17
Author(s):  
ALESSANDRA GERLI ◽  
LEENDERT C. EIGENBROOD
Keyword(s):  
Ash Content ◽  
The Novel ◽  
Offset Printing ◽  
Excellent Correlation ◽  
End Conditions ◽  
Bottom Side ◽  
Novel Method ◽  
Total Fraction

A novel method was developed for the determination of linting propensity of paper based on printing with an IGT printability tester and image analysis of the printed strips. On average, the total fraction of the surface removed as lint during printing is 0.01%-0.1%. This value is lower than those reported in most laboratory printing tests, and more representative of commercial offset printing applications. Newsprint paper produced on a roll/blade former machine was evaluated for linting propensity using the novel method and also printed on a commercial coldset offset press. Laboratory and commercial printing results matched well, showing that linting was higher for the bottom side of paper than for the top side, and that linting could be reduced on both sides by application of a dry-strength additive. In a second case study, varying wet-end conditions were used on a hybrid former machine to produce four paper reels, with the goal of matching the low linting propensity of the paper produced on a machine with gap former configuration. We found that the retention program, by improving fiber fines retention, substantially reduced the linting propensity of the paper produced on the hybrid former machine. The papers were also printed on a commercial coldset offset press. An excellent correlation was found between the total lint area removed from the bottom side of the paper samples during laboratory printing and lint collected on halftone areas of the first upper printing unit after 45000 copies. Finally, the method was applied to determine the linting propensity of highly filled supercalendered paper produced on a hybrid former machine. In this case, the linting propensity of the bottom side of paper correlated with its ash content.

Determination of rate constants of redox reactions of second order from current-less potential-time curves by a simplified graphical-numerical method

1983 ◽  
Vol 48 (5) ◽  
pp. 1358-1367 ◽  
Author(s):  
Antonín Tockstein ◽  
František Skopal
Keyword(s):  
Numerical Method ◽  
Explicit Form ◽  
Rate Constant ◽  
Optimization Algorithm ◽  
Rate Constants ◽  
Redox Reactions ◽  
Second Order ◽  
Wide Region ◽  
Recurrent Formula

A method for constructing curves is proposed that are linear in a wide region and from whose slopes it is possible to determine the rate constant, if a parameter, θ, is calculated numerically from a rapidly converging recurrent formula or from its explicit form. The values of rate constants and parameter θ thus simply found are compared with those found by an optimization algorithm on a computer; the deviations do not exceed ±10%.

Comparative Study for the Assay of Plant Derived Chemicals in Pharmaceutical Formulation Using Methods Dependent on Factorized Spectra

2021 ◽  
Author(s):  
Nesma M Fahmy ◽  
Adel M Michael
Keyword(s):  
Pharmaceutical Formulations ◽  
Pharmaceutical Formulation ◽  
Ternary Mixtures ◽  
Ratio Method ◽  
The Novel ◽  
Naturally Occurring ◽  
Accuracy And Precision ◽  
Validation Parameters ◽  
Significant Difference

Abstract Background Modern built-in spectrophotometer software supporting mathematical processes provided a solution for increasing selectivity for multicomponent mixtures. Objective Simultaneous spectrophotometric determination of the three naturally occurring antioxidants—rutin(RUT), hesperidin(HES), and ascorbic acid(ASC)—in bulk forms and combined pharmaceutical formulation. Method This was achieved by factorized zero order method (FZM), factorized derivative method (FD1M), and factorized derivative ratio method (FDRM), coupled with spectrum subtraction(SS). Results Mathematical filtration techniques allowed each component to be obtained separately in either its zero, first, or derivative ratio form, allowing the resolution of spectra typical to the pure components present in Vitamin C Forte® tablets. The proposed methods were applied over a concentration range of 2–50, 2–30, and 10–100 µg/mL for RUT, HES, and ASC, respectively. Conclusions Recent methods for the analysis of binary mixtures, FZM and FD1M, were successfully applied for the analysis of ternary mixtures and compared to the novel FDRM. All were revealed to be specific and sensitive with successful application on pharmaceutical formulations. Validation parameters were evaluated in accordance with the International Conference on Harmonization guidelines. Statistical results were satisfactory, revealing no significant difference regarding accuracy and precision. Highlights Factorized methods enabled the resolution of spectra identical to those of pure drugs present in mixtures. Overlapped spectra of ternary mixtures could be resolved by spectrum subtraction coupled FDRM (SS-FDRM) or by successive application of FZM and FD1M.

A hybrid analytical-numerical method based on Isogeometric Analysis for determination of time varying gear mesh stiffness

2021 ◽  
Vol 160 ◽  
pp. 104291
Author(s):  
Andreas Beinstingel ◽  
Michael Keller ◽  
Michael Heider ◽  
Burkhard Pinnekamp ◽  
Steffen Marburg
Keyword(s):  
Numerical Method ◽  
Isogeometric Analysis ◽  
Time Varying ◽  
Mesh Stiffness ◽  
Gear Mesh ◽  
Gear Mesh Stiffness
Sign in / Sign up

Export Citation Format

Share Document