scholarly journals Selective two-photon absorptive resonance femtosecond-laser electronic-excitation tagging velocimetry

2016 ◽  
Vol 41 (10) ◽  
pp. 2225 ◽  
Author(s):  
Naibo Jiang ◽  
Benjamin R. Halls ◽  
Hans U. Stauffer ◽  
Paul M. Danehy ◽  
James R. Gord ◽  
...  
Keyword(s):  
Femtosecond Laser ◽  
Electronic Excitation ◽  
Two Photon

Inorganic-organic Hybrid Materials for Real 3-D Sub-νm Lithography

2003 ◽  
Vol 780 ◽  
Author(s):  
R. Houbertz ◽  
J. Schulz ◽  
L. Fröhlich ◽  
G. Domann ◽  
M. Popall ◽  
...  
Keyword(s):  
Femtosecond Laser ◽  
Sol Gel ◽  
Laser Pulses ◽  
Femtosecond Laser Pulses ◽  
Hybrid Polymer ◽  
Organic Hybrid ◽  
Two Photon ◽  
Applied Technology ◽  
Scale Structures ◽  
Sol Gel Synthesis

AbstractReal 3-D sub-νm lithography was performed with two-photon polymerization (2PP) using inorganic-organic hybrid polymer (ORMOCER®) resins. The hybrid polymers were synthesized by hydrolysis/polycondensation reactions (modified sol-gel synthesis) which allows one to tailor their material properties towards the respective applications, i.e., dielectrics, optics or passivation. Due to their photosensitive organic functionalities, ORMOCER®s can be patterned by conventional photo-lithography as well as by femtosecond laser pulses at 780 nm. This results in polymerized (solid) structures where the non-polymerized parts can be removed by conventional developers.ORMOCER® structures as small as 200 nm or even below were generated by 2PP of the resins using femtosecond laser pulses. It is demonstrated that ORMOCER®s have the potential to be used in components or devices built up by nm-scale structures such as, e.g., photonic crystals. Aspects of the materials in conjunction to the applied technology are discussed.

Picosecond Single-Photon and Femtosecond Two-Photon Pulsed Laser Stimulation for IC Characterization and Failure Analysis

2009 ◽  
Author(s):  
V. Pouget ◽  
E. Faraud ◽  
K. Shao ◽  
S. Jonathas ◽  
D. Horain ◽  
...  
Keyword(s):  
Femtosecond Laser ◽  
Single Photon ◽  
Pulsed Laser ◽  
Laser Pulses ◽  
Femtosecond Laser Pulses ◽  
Ultrashort Laser Pulses ◽  
Laser Stimulation ◽  
Two Photon ◽  
Resolution Improvement ◽  
Ultrashort Laser

Abstract This paper presents the use of pulsed laser stimulation with picosecond and femtosecond laser pulses. We first discuss the resolution improvement that can be expected when using ultrashort laser pulses. Two case studies are then presented to illustrate the possibilities of the pulsed laser photoelectric stimulation in picosecond single-photon and femtosecond two-photon modes.

Fabrication of Three-Dimensional Micro-Structures with Two-Photon Absorption by Femtosecond Laser

2006 ◽  
Vol 532-533 ◽  
pp. 568-571
Author(s):  
Ming Zhou ◽  
Hai Feng Yang ◽  
Li Peng Liu ◽  
Lan Cai
Keyword(s):  
Photonic Crystal ◽  
Femtosecond Laser ◽  
Detection System ◽  
Three Dimensional ◽  
Photon Absorption ◽  
Micro Fabrication ◽  
Two Photon Absorption ◽  
Two Photon ◽  
Photo Polymerization ◽  
System A

The photo-polymerization induced by Two-Photon Absorption (TPA) is tightly confined in the focus because the efficiency of TPA is proportional to the square of intensity. Three-dimensional (3D) micro-fabrication can be achieved by controlling the movement of the focus. Based on this theory, a system for 3D-micro-fabrication with femtosecond laser is proposed. The system consists of a laser system, a microscope system, a real-time detection system and a 3D-movement system, etc. The precision of micro-machining reaches a level down to 700nm linewidth. The line width was inversely proportional to the fabrication speed, but proportional to laser power and NA. The experiment results were simulated, beam waist of 0.413μm and TPA cross section of 2×10-54cm4s was obtained. While we tried to optimize parameters, we also did some research about its applications. With TPA photo-polymerization by means of our experimental system, 3D photonic crystal of wood-pile structure twelve layers and photonic crystal fiber are manufactured. These results proved that the micro-fabrication system of TPA can not only obtain the resolution down to sub-micron level, but also realize real 3D micro-fabrication.

Modified threshold of two-photon-pumped random lasing of ZnO nanorods by femtosecond laser ablation

2012 ◽  
Vol 112 (6) ◽  
pp. 063102 ◽  
Author(s):  
Jun Dai ◽  
Zhi-Cheng Fu ◽  
Sheng Lan ◽  
Xia Wan ◽  
Shao-Long Tie ◽  
...  
Keyword(s):  
Laser Ablation ◽  
Femtosecond Laser ◽  
Zno Nanorods ◽  
Femtosecond Laser Ablation ◽  
Random Lasing ◽  
Two Photon
Sign in / Sign up

Export Citation Format

Share Document