Fiber-Optic Frequency Shifting of THz-Range WDM Signal Using Orthogonal Pump-Signal Polarization Configuration

2018 ◽  
Author(s):  
Tomoyuki Kato ◽  
Shigeki Watanabe ◽  
Takahito Tanimura ◽  
Robert Elschner ◽  
Carsten Schmidt-Langhorst ◽  
...  
Keyword(s):  
Fiber Optic ◽  
Pump Signal ◽  
Thz Range ◽  
Polarization Configuration ◽  
Frequency Shifting

A Fiber-Optic Laser-Doppler Probe for Vibration Analysis of Rotating Machines

1980 ◽  
Vol 102 (3) ◽  
pp. 607-612 ◽  
Author(s):  
R. A. Cookson ◽  
P. Bandyopadhyay
Keyword(s):  
Fiber Optic ◽  
Scattered Light ◽  
Laser Doppler ◽  
Probe Laser ◽  
Fiber Optic Probe ◽  
Rotating System ◽  
Doppler Probe ◽  
Optic Probe ◽  
Similar Accuracy ◽  
Frequency Shifting

The problem of obtaining vibratory information from remote, rotating, components within a machine has been overcome by means of a laser-Doppler fiber-optic probe. Laser light is transmitted down the fiber-optic and scattered light is returned for analysis in the same way. The Twyman-Green mode of operation of the laser-Doppler system has been shown to have serious shortcomings for this type of work and a new mode has been produced, and used successfully, in conjunction with Bragg cells for frequency shifting. The use of a single set of Bragg cells to compensate for the average velocity of a rotating system, limits the allowable speed of rotation to about 1000 rpm. However, other techniques for frequency shifting are available. An experimental investigation is reported in which a rotating system, consisting of a disk carrying flat cantilever blades, was rotated at about 1000 rpm while one of the blades was excited at 163 Hz. The measured frequency of the vibrating blade was 162.8 Hz and similar accuracy was obtained for the amplitude measurements.

Distributed Fiber Optic Brillouin Sensing Technique with Frequency Shifting

2011 ◽  
Vol 40 (9) ◽  
pp. 1428-1432 ◽  
Author(s):  
黄民双 HUANG Min-shuang ◽  
黄军芬 HUANG Jun-fen
Keyword(s):  
Fiber Optic ◽  
Frequency Shifting

Imaging and diffraction modes in Scanning Transmission Electron Microscopy

1986 ◽  
Vol 44 ◽  
pp. 684-687
Author(s):  
J. M. Cowley ◽  
R. Glaisher ◽  
J. A. Lin ◽  
H.-J. Ou
Keyword(s):  
Scanning Transmission Electron Microscopy ◽  
High Efficiency ◽  
Fiber Optic ◽  
Image Intensifier ◽  
Detector System ◽  
Detector Plane ◽  
Secondary Electrons ◽  
Transmission Electron ◽  
Scanning Transmission ◽  
Special Detector

Some of the most important applications of STEM depend on the variety of imaging and diffraction made possible by the versatility of the detector system and the serial nature, of the image acquisition. A special detector system, previously described, has been added to our STEM instrument to allow us to take full advantage of this versatility. In this, the diffraction pattern in the detector plane may be formed on either of two phosphor screens, one with P47 (very fast) phosphor and the other with P20 (high efficiency) phosphor. The light from the phosphor is conveyed through a fiber-optic rod to an image intensifier and TV system and may be photographed, recorded on videotape, or stored digitally on a frame store. The P47 screen has a hole through it to allow electrons to enter a Gatan EELS spectrometer. Recently a modified SEM detector has been added so that high resolution (10Å) imaging with secondary electrons may be used in conjunction with other modes.

Synthesis, performance and growth mechanism of silver nanoparticle coated SERS fiber probe

2019 ◽  
Vol 107 (3) ◽  
pp. 305
Author(s):  
Mengmei Geng ◽  
Yuting Long ◽  
Tongqing Liu ◽  
Zijuan Du ◽  
Hong Li ◽  
...  
Keyword(s):  
Silver Nanoparticles ◽  
Absorption Spectrum ◽  
Reaction Time ◽  
Growth Mechanism ◽  
Fiber Optic ◽  
Fiber Optic Probe ◽  
Visible Absorption ◽  
Fiber Probe ◽  
Surface Enhanced Raman ◽  
Optic Probe

Surface-enhanced Raman Scattering (SERS) fiber probe provides abundant interaction area between light and materials, permits detection within limited space and is especially useful for remote or in situ detection. A silver decorated SERS fiber optic probe was prepared by hydrothermal method. This method manages to accomplish the growth of silver nanoparticles and its adherence on fiber optic tip within one step, simplifying the synthetic procedure. The effects of reaction time on phase composition, surface plasmon resonance property and morphology were investigated by X-ray diffraction analysis (XRD), ultraviolet-visible absorption spectrum (UV-VIS absorption spectrum) and scanning electron microscope (SEM). The results showed that when reaction time is prolonged from 4–8 hours at 180 °C, crystals size and size distribution of silver nanoparticles increase. Furthermore, the morphology, crystal size and distribution density of silver nanoparticles evolve along with reaction time. A growth mechanism based on two factors, equilibrium between nucleation and growth, and the existence of PVP, is hypothesized. The SERS fiber probe can detect rhodamin 6G (R6G) at the concentration of 10−6 M. This SERS fiber probe exhibits promising potential in organic dye and pesticide residue detection.

Increasing the information capacity of a fiber-optic multi-sensor converter of binary mechanical signals into electrical signals

2020 ◽  
pp. 15-23
Author(s):  
V. M. Grechishnikov ◽  
E. G. Komarov
Keyword(s):  
Fiber Optic ◽  
Information Capacity ◽  
Parallel Structure ◽  
Optical Scheme ◽  
Digital To Analog Converter ◽  
Electrical Signals ◽  
Mechanical Signals ◽  
Analog Converter ◽  
Output Code ◽  
Digital To Analog

The design and operation principle of a multi-sensor Converter of binary mechanical signals into electrical signals based on a partitioned fiber-optic digital-to-analog Converter with a parallel structure is considered. The digital-to-analog Converter is made from a set of simple and technological (three to five digit) fiber-optic digital-to-analog sections. The advantages of the optical scheme of the proposed. Converter in terms of metrological and energy characteristics in comparison with single multi-bit converters are justified. It is shown that by increasing the number of digital-analog sections, it is possible to repeatedly increase the information capacity of a multi-sensor Converter without tightening the requirements for its manufacturing technology and element base. A mathematical model of the proposed Converter is developed that reflects the features of its operation in the mode of sequential time conversion of the input code vectors of individual fiber-optic sections into electrical analogues and the formation of the resulting output code vector.

Hydrostatic Fiber Optic Liquid Level Sensor with position sensitive detector

Metrologiya ◽  
2020 ◽  
pp. 38-51
Author(s):  
V. N. Astapov ◽  
I. N. Kozlova
Keyword(s):  
Fiber Optic ◽  
Effective Area ◽  
Raw Material ◽  
Position Sensitive Detector ◽  
Fiber Optic Sensor ◽  
Liquid Level ◽  
Problem Solution ◽  
Sensitive Detector ◽  
Position Sensitive ◽  
Triangulation Sensor

This article presents the rationale and methodology for developing an intrinsically safe device, namely, a hydrostatic fiber optic sensor with a position-sensitive detector for monitoring the level of oil products in large-capacity tanks at oil depots and during pumping in a raw material warehouses. This device suitable for continuous monitoring of the liquid level, based on the measurement of a hydrostatic column of liquid with automatic offset of changes in the density of the liquid. Offset is carried out by means of a displacer (a fully submerged float), inside which a housing with a position-sensitive detector (PSD) is integrated. Theoretical validation of the bellows suspension usage for a displacer is given. During filling a container with a liquid whose level is measured, liquid bellows, the movement of which is recorded by an optical triangulation sensor using the reflected infrared ray incident on the bottom of the bellows. The principle of the triangulation sensor operation is based on the geometric properties of the triangles. The pulses of infrared radiation come through a fiber optic cable. In order to measure the movement of the surface (the bottom of the bellows) by measuring the movement of the reflected beam, a position-sensitive detector is used, which is located in a remote controller. In this device for the intrinsic safety problem solution, optical inputs of a fiber optic flat cable are located in the active zone of the sensor, which is connected to the optical inputs of a position-sensitive detector, operated on the principles of photoelectric effect. The light spot moving along the sensitive zone and converted by the detector into a one-dimensional signal proportional to the distance to the object. hydrostatically applies pressure over the entire effective area of the measuring

High-voltage monitoring by the fiber-optic recirculating measuring system

2020 ◽  
pp. 38-44
Author(s):  
A. V. Polyakov ◽  
M. A. Ksenofontov
Keyword(s):  
Optical Fibers ◽  
High Voltage ◽  
Optical Sensors ◽  
Electromagnetic Interference ◽  
Fiber Optic ◽  
Electric Power Industry ◽  
Measuring System ◽  
Voltage Range ◽  
External Electromagnetic Fields ◽  
Optic Communication

Optical technologies for measuring electrical quantities attract great attention due to their unique properties and significant advantages over other technologies used in high-voltage electric power industry: the use of optical fibers ensures high stability of measuring equipment to electromagnetic interference and galvanic isolation of high-voltage sensors; external electromagnetic fields do not influence the data transmitted from optical sensors via fiber-optic communication lines; problems associated with ground loops are eliminated, there are no side electromagnetic radiation and crosstalk between the channels. The structure and operation principle of a quasi-distributed fiber-optic high-voltage monitoring system is presented. The sensitive element is a combination of a piezo-ceramic tube with an optical fiber wound around it. The device uses reverse transverse piezoelectric effect. The measurement principle is based on recording the change in the recirculation frequency under the applied voltage influence. When the measuring sections are arranged in ascending order of the measured effective voltages relative to the receiving-transmitting unit, a relative resolution of 0,3–0,45 % is achieved for the PZT-5H and 0,8–1,2 % for the PZT-4 in the voltage range 20–150 kV.

Sign in / Sign up

Export Citation Format

Share Document