Subcooled Water Flow Boiling at 1.66 MPa under Uniform High Heat Flux Conditions

1989 ◽  
Vol 16 (3) ◽  
pp. 324-330 ◽  
Author(s):  
Ronald D. Boyd
Keyword(s):  
Heat Flux ◽  
Water Flow ◽  
Flow Boiling ◽  
High Heat ◽  
High Heat Flux ◽  
Subcooled Water

Numerical simulation in a subcooled water flow boiling for one-sided high heat flux in reactor divertor

2016 ◽  
Vol 112 ◽  
pp. 587-593 ◽  
Author(s):  
P. Liu ◽  
X.B. Peng ◽  
Y.T. Song ◽  
X.D. Fang ◽  
S.H. Huang ◽  
...  
Keyword(s):  
Numerical Simulation ◽  
Heat Flux ◽  
Water Flow ◽  
Flow Boiling ◽  
High Heat ◽  
High Heat Flux ◽  
Subcooled Water

Critical Heat Flux (CHF) Correlations for Subcooled Water Flow Boiling at High Pressure and High Heat Flux

2021 ◽  
Vol 30 (1) ◽  
pp. 279-293
Author(s):  
Ping Liu ◽  
Yusheng Guo ◽  
Wenlong Ding ◽  
Mingyun Tang ◽  
Yuntao Song ◽  
...  
Keyword(s):  
Heat Flux ◽  
High Pressure ◽  
Critical Heat Flux ◽  
Water Flow ◽  
Flow Boiling ◽  
High Heat ◽  
High Heat Flux ◽  
Subcooled Water

Review on high heat flux flow boiling of refrigerants and water for electronics cooling

2021 ◽  
Vol 180 ◽  
pp. 121787
Author(s):  
Behnam Parizad Benam ◽  
Abdolali Khalili Sadaghiani ◽  
Vedat Yağcı ◽  
Murat Parlak ◽  
Khellil Sefiane ◽  
...  
Keyword(s):  
Heat Flux ◽  
Flow Boiling ◽  
Electronics Cooling ◽  
High Heat ◽  
High Heat Flux ◽  
Flux Flow

Study on onset of nucleate boiling with screw tube for fusion reactor application

2021 ◽  
Author(s):  
Ji Hwan Lim ◽  
Minkyu Park
Keyword(s):  
Heat Transfer ◽  
Heat Flux ◽  
Flow Boiling ◽  
Nucleate Boiling ◽  
High Heat ◽  
Transfer Mechanism ◽  
High Heat Flux ◽  
Heat Transfer Mechanism ◽  
System Parameters ◽  
Smooth Tubes

Abstract The onset of nucleate boiling (ONB) is the point at which the heat transfer mechanism in fluids changes and is one of the thermo-hydraulic factors that must be considered when establishing a cooling system operation strategy. Because the high heat flux of several MW/m2, which is loaded within a tokamak, is applied under a one-side heating condition, it is necessary to determine a correlative relation that can predict ONB under special heating conditions. In this study, the ONB of a one-side-heated screw tube was experimentally analyzed via a subcooled flow boiling experiment. The helical nut structure of the screw tube flow path wall allows for improved heat transfer performance relative to smooth tubes, providing a screw tube with a 53.98% higher ONB than a smooth tube. The effects of the system parameters on the ONB heat flux were analyzed based on the changes in the heat transfer mechanism, with the results indicating that the flow rate and degree of subcooling are proportional to the ONB heat flux because increasing these factors improves the forced convection heat transfer and increases the condensation rate, respectively. However, it was observed that the liquid surface tension and latent heat decrease as the pressure increases, leading to a decrease in the ONB heat flux. An evaluation of the predictive performance of existing ONB correlations revealed that most have high error rates because they were developed based on ONB experiments on micro-channels or smooth tubes and not under one-side high heat load conditions. To address this, we used dimensional analysis based on Python code to develop new ONB correlations that reflect the influence of system parameters.

Heat Transfer Enhancement in Compact Phase Change Microchannel Heat Exchangers for High Flux Laser Diodes

2018 ◽  
Author(s):  
Jensen Hoke ◽  
Todd Bandhauer ◽  
Jack Kotovsky ◽  
Julie Hamilton ◽  
Paul Fontejon
Keyword(s):  
Heat Transfer ◽  
Heat Flux ◽  
Phase Change ◽  
Flow Boiling ◽  
Laser Diodes ◽  
High Heat ◽  
Heat Fluxes ◽  
High Heat Flux ◽  
Maximum Heat ◽  
Average Maximum

Liquid-vapor phase change heat transfer in microchannels offers a number of significant advantages for thermal management of high heat flux laser diodes, including reduced flow rates and near constant temperature heat rejection. Modern laser diode bars can produce waste heat loads >1 kW cm−2, and prior studies show that microchannel flow boiling heat transfer at these heat fluxes is possible in very compact heat exchanger geometries. This paper describes further performance improvements through area enhancement of microchannels using a pyramid etching scheme that increases heat transfer area by ∼40% over straight walled channels, which works to promote heat spreading and suppress dry-out phenomenon when exposed to high heat fluxes. The device is constructed from a reactive ion etched silicon wafer bonded to borosilicate to allow flow visualization. The silicon layer is etched to contain an inlet and outlet manifold and a plurality of 40μm wide, 200μm deep, 2mm long channels separated by 40μm wide fins. 15μm wide 150μm long restrictions are placed at the inlet of each channel to promote uniform flow rate in each channel as well as flow stability in each channel. In the area enhanced parts either a 3μm or 6μm sawtooth pattern was etched vertically into the walls, which were also scalloped along the flow path with the a 3μm periodicity. The experimental results showed that the 6μm area-enhanced device increased the average maximum heat flux at the heater to 1.26 kW cm2 using R134a, which compares favorably to a maximum of 0.95 kw cm2 dissipated by the plain walled test section. The 3μm area enhanced test sections, which dissipated a maximum of 1.02 kW cm2 showed only a modest increase in performance over the plain walled test sections. Both area enhancement schemes delayed the onset of critical heat flux to higher heat inputs.

A theoretical and experimental study on subcooled flow boiling at high heat flux

1994 ◽  
Vol 29 (5) ◽  
pp. 319-327 ◽  
Author(s):  
K. W. Lin ◽  
C. H. Lee ◽  
L. W. Hourng ◽  
J. C. Hsu
Keyword(s):  
Experimental Study ◽  
Heat Flux ◽  
Flow Boiling ◽  
High Heat ◽  
High Heat Flux ◽  
Subcooled Flow Boiling ◽  
Subcooled Flow
Sign in / Sign up

Export Citation Format

Share Document