Design and Test of a Double-Curved Guiding Groove for a High-Speed Precision Seed-Metering Device

2020 ◽  
Vol 63 (5) ◽  
pp. 1349-1360
Author(s):  
Pan Xue ◽  
Yujun Hao ◽  
Wan Jiao ◽  
Jie Ren ◽  
Feifei Yang ◽  
...  
Keyword(s):  
Inclination Angle ◽  
High Speed ◽  
Element Model ◽  
Discrete Element ◽  
Travel Speed ◽  
Curved Surface ◽  
Discrete Element Model ◽  
Release Point ◽  
Seed Spacing ◽  
Seed Metering Device

HighlightsThe instability of the seed release point in a seed-metering device is proved theoretically.A double-curved guiding groove at the seed-release point improves the seed-metering uniformity.A discrete element model was used to examine effects of the design parameters on the metering performance.The critical parameters for the double-curved guiding groove design were determined.Abstract. The instability of the seed release point in a seed-metering device is one of the main causes of the non-uniformity of seed spacing. To improve the seed spacing uniformity, a double-curved guiding groove (DGG) was designed based on the prerelease adaptive principle. The DGG was used at the seed release point of an existing high-speed precision soybean seed-metering device with a double-setting plate. The results showed that the prerelease curved surface of the DGG was capable of guiding seeds to be released at the same seed release point at all times, and the adaptive curved surface of the DGG prevented any changes in seed velocity caused by friction or collisions between seeds and the meter, thereby improving the seed spacing uniformity significantly. A discrete element model was developed and validated with laboratory tests. Through simulations using the model, the primary and secondary factors of the DGG impacting the qualified rate of seed metering (QRM) and the coefficient of variation of the seed spacing uniformity (CVU) were identified and were, in descending order, the spacing of prerelease (SPR), the starting position of prerelease (SPP), the inclination angle of the seed outlet (ASO), and the inclination angle of the receiving cup (ABR). Regression equations of the QRM and CVU with the two main impacting factors were then established. For a planter travel speed of 10 km h-1, the optimal SPR was 10 mm, and the optimal SPP was 40°, where the QRM was 100% and the CVU was 16.61%. When compared to seed metering without the DGG, the CVU was reduced by 2.55%, showing that the DGG significantly improved the uniformity of seed spacing. Keywords: Double-curved guiding groove, Discrete element method, Seed-metering device, Travel speed, Uniformity.

Simulation of Fully Sintering Dental Zirconia Milling Process Based on Discrete Element Method

2013 ◽  
Vol 568 ◽  
pp. 49-54
Author(s):  
H.B. Wu ◽  
Q.P. Sun ◽  
Dun Wen Zuo
Keyword(s):  
High Speed ◽  
Cutting Tool ◽  
Cutting Speed ◽  
Element Model ◽  
Discrete Element ◽  
Milling Process ◽  
Discrete Element Model ◽  
Surface Cracks ◽  
Coating Technology ◽  
Cutting Speeds

Discrete element model of fully sintering dental zirconia was constructed and calibrated. Based on the model, the dynamic process of low-speed milling of zirconia was simulated, and the effects of different cutting speeds, cutting widths and federates on the formation of surface cracks were also analyzed. Results show that residue cracks number and maximum depth increases significantly with increase of the cutting width, while the influence of cutting speed and federates is not distinct. That shows the possibility of high-speed machining on fully sintering dental zirconia with development of coating technology of cutting tool.

scholarly journals Discrete element model for general polyhedra

2021 ◽  
Author(s):  
Alfredo Gay Neto ◽  
Peter Wriggers
Keyword(s):  
Frictional Contact ◽  
Virtual Work ◽  
Particle Surface ◽  
Element Model ◽  
Discrete Element ◽  
Discrete Element Model ◽  
Principle Of Virtual Work ◽  
Dynamics Model ◽  
Railway Ballast ◽  
Multibody Dynamics Model

AbstractWe present a version of the Discrete Element Method considering the particles as rigid polyhedra. The Principle of Virtual Work is employed as basis for a multibody dynamics model. Each particle surface is split into sub-regions, which are tracked for contact with other sub-regions of neighboring particles. Contact interactions are modeled pointwise, considering vertex-face, edge-edge, vertex-edge and vertex-vertex interactions. General polyhedra with triangular faces are considered as particles, permitting multiple pointwise interactions which are automatically detected along the model evolution. We propose a combined interface law composed of a penalty and a barrier approach, to fulfill the contact constraints. Numerical examples demonstrate that the model can handle normal and frictional contact effects in a robust manner. These include simulations of convex and non-convex particles, showing the potential of applicability to materials with complex shaped particles such as sand and railway ballast.

Study on Machining Mechanism of Glass Using Discrete Element Method

2014 ◽  
Vol 577 ◽  
pp. 108-111 ◽  
Author(s):  
Ying Qiu ◽  
Mei Lin Gu ◽  
Feng Guang Zhang ◽  
Zhi Wei
Keyword(s):  
Discrete Element Method ◽  
Element Model ◽  
Discrete Element ◽  
Rake Angle ◽  
Milling Process ◽  
Micro Milling ◽  
Discrete Element Model ◽  
Machined Surface ◽  
Damage Depth ◽  
Element Method

The discrete element method (DEM) is applied to glass micromachining in this study. By three standard tests the discrete element model is established to match the main mechanical properties of glass. Then, indentating, cutting, micro milling process are simulated. Results show that the vertical damage depth is prevented from reaching the final machined surface in cutting process. Tool rake angle is the most remarkable factor influencing on the chip deformation and cutting force. The final machined surface is determined by the minimum cutting thickness per edge. Different cutting thickness, cutter shape and spindle speed largely effect on the mechanism of glass.

Reduced Rough-Surface Parametrization for Use With the Discrete-Element Model

2009 ◽  
Vol 131 (2) ◽  
Author(s):  
Stephen T. McClain ◽  
Jason M. Brown
Keyword(s):  
Heat Transfer ◽  
Rough Surface ◽  
Surface Characterization ◽  
Rough Surfaces ◽  
Roughness Element ◽  
Three Dimensional ◽  
Element Model ◽  
Discrete Element ◽  
Diameter Distribution ◽  
Discrete Element Model

The discrete-element model for flows over rough surfaces was recently modified to predict drag and heat transfer for flow over randomly rough surfaces. However, the current form of the discrete-element model requires a blockage fraction and a roughness-element diameter distribution as a function of height to predict the drag and heat transfer of flow over a randomly rough surface. The requirement for a roughness-element diameter distribution at each height from the reference elevation has hindered the usefulness of the discrete-element model and inhibited its incorporation into a computational fluid dynamics (CFD) solver. To incorporate the discrete-element model into a CFD solver and to enable the discrete-element model to become a more useful engineering tool, the randomly rough surface characterization must be simplified. Methods for determining characteristic diameters for drag and heat transfer using complete three-dimensional surface measurements are presented. Drag and heat transfer predictions made using the model simplifications are compared to predictions made using the complete surface characterization and to experimental measurements for two randomly rough surfaces. Methods to use statistical surface information, as opposed to the complete three-dimensional surface measurements, to evaluate the characteristic dimensions of the roughness are also explored.

A CUBIC ARRANGED SPHERICAL DISCRETE ELEMENT MODEL

2014 ◽  
Vol 11 (05) ◽  
pp. 1350102 ◽  
Author(s):  
WEI GAO ◽  
YUANQIANG TAN ◽  
MENGYAN ZANG
Keyword(s):  
Strain Energy ◽  
Element Model ◽  
Discrete Element ◽  
Discrete Element Model ◽  
Laminated Plate ◽  
Discrete Elements ◽  
Elastic Continuum ◽  
Vibration Process ◽  
Spring Constants ◽  
Dem Model

A 3D discrete element model (DEM model) named cubic arranged discrete element model is proposed. The model treats the interaction between two connective discrete elements as an equivalent "beam" element. The spring constants between two connective elements are obtained based on the equivalence of strain energy stored in a unit volume of elastic continuum. Following that, the discrete element model proposed and its algorithm are implemented into the in-house developed code. To test the accuracy of the DEM model and its algorithm, the vibration process of the block, a homogeneous plate and laminated plate under impact loading are simulated in elastic range. By comparing the results with that calculated by using LS-DYNA, it is found that they agree with each other very well. The accuracy of the DEM model and its algorithm proposed in this paper is proved.

Sign in / Sign up

Export Citation Format

Share Document