Analysis of Air Cargo Temperature Variations During Transport Operations

2018 ◽  
Vol 61 (2) ◽  
pp. 723-732
Author(s):  
William Pelletier ◽  
Khe V. Chau ◽  
Ray A. Bucklin ◽  
Jeffrey K. Brecht ◽  
David W. Hahn ◽  
...  
Keyword(s):  
Heat Transfer ◽  
Temperature Distribution ◽  
Air Transport ◽  
Temperature Sensitive ◽  
Perishable Products ◽  
Air Cargo ◽  
Temperature Variations ◽  
Horticultural Crops ◽  
Cold Room ◽  
The Subject

Abstract. Air transport has unique characteristics that are essential for the transport of perishable products. However, temperature variations during air transport operations may be detrimental to temperature-sensitive products such as fresh horticultural crops, seafood, pharmaceuticals, and others. The literature on the subject remains scarce. In-flight temperatures were monitored during six international shipments using an aircraft container loaded with simulated perishable products. Results highlighted the overriding impact of solar radiation on temperature distribution within aircraft containers during ramp transfers. Extended ramp transfer durations were observed, and for three shipments the total time, outside, on the tarmac exceeded 11 h, resulting in an average product temperature increase of as much as 13°C. In-flight conditions had a smaller impact on the temperature distribution within the load of products. Tests indicated that the core region of the load was exposed to the smallest rate of heat transfer, and the top layer was exposed to the largest rate of heat transfer. Cold room storage of a fully loaded aircraft container proved to be a very inefficient cooling method. Keywords: Aircraft container, Horticultural products, In-flight, Perishables, Ramp, Tarmac.

Numerical Simulation of Solidification Process for a Machine Tool Bed

2011 ◽  
Vol 675-677 ◽  
pp. 987-990
Author(s):  
Ling Tang ◽  
Xu Dong Wang ◽  
Hai Jing Zhao ◽  
Man Yao
Keyword(s):  
Heat Transfer ◽  
Temperature Field ◽  
Temperature Distribution ◽  
Machine Tool ◽  
Computation Time ◽  
Solidification Process ◽  
Field Calculation ◽  
Original Design ◽  
Calculation Results ◽  
Improved Design

In this paper, the flow, heat transfer and stress during solidification process of the machine tool bed weighed about 2.5ton that has been optimized by structural topologymethod, was calculated with ProCAST software, and the causes of the crack forming in the casting of the machine tool bed was analysed. According to the calculation results, the structural design of the local part where cracks tends to form has been improved, and the heat transfer and the stress are calculated again. By comparing the temperature field with filling of molten cast iron and without filling, it has been found that there was little effect of filling on the results of temperature distribution of the cast, therefore the effect of filling can be ignored in the following temperature field calculation to save computation time. The model has been simplified in the stress field calculation with considering the complexity of the machine tool bed and the cost of computation. Then, the merits and demerits of the original design and the improved design are compared and analyzed depending on the calculated temperature and stress results. It is suggested that the improved one could get a more uniform temperature distribution and then the trend of the crack occurring can be greatly reduced. These results could provide a guide for the actual casting production, achieving the scientific control of the production of castings, ensuring the quality of the castings.

Investigation Into Thermal Stress Characteristics of Pipe-in-Pipe Under High Temperature Condition

2018 ◽  
Author(s):  
Si-Hwa Jeong ◽  
Min-Gu Won ◽  
Nam-Su Huh ◽  
Yun-Jae Kim ◽  
Young-Jin Oh ◽  
...  
Keyword(s):  
Heat Transfer ◽  
Thermal Stress ◽  
High Temperature ◽  
Temperature Distribution ◽  
Heat Transfer Analysis ◽  
Piping System ◽  
Curved Pipe ◽  
High Temperature Condition ◽  
Single Pipe ◽  
Radiation Conditions

In this paper, the thermal stress characteristics of the pipe-in-pipe (PIP) system under high temperature condition are analyzed. The PIP is a type of pipe applied in sodium-cooled faster reactor (SFR) and has a different geometry from a single pipe. In particular, under the high temperature condition of the SFR, the high thermal stress is generated due to the temperature gradient occurring between the inner pipe and outer pipe. To investigate the thermal stress characteristics, three cases are considered according to geometry of the support. The fully constrained support and intermediate support are considered for case 1 and 2, respectively. For case 3, both supports are applied to the actual curved pipe. The finite element (FE) analyses are performed in two steps for each case. Firstly, the heat transfer analysis is carried out considering the thermal conduction, convection and radiation conditions. From the heat transfer analysis, the temperature distribution results in the piping system are obtained. Secondly, the structural analysis is performed considering the temperature distribution results and boundary conditions. Finally, the effects of the geometric characteristics on the thermal stress in the PIP system are analyzed.

Experimental and Numerical Evaluation of Small-Scale Cryosurgery Using Ultrafine Cryoprobe

2013 ◽  
Vol 4 (4) ◽  
Author(s):  
Junnosuke Okajima ◽  
Atsuki Komiya ◽  
Shigenao Maruyama
Keyword(s):  
Heat Transfer ◽  
Numerical Simulation ◽  
Heat Transfer Coefficient ◽  
Temperature Distribution ◽  
Surface Temperature ◽  
Numerical Evaluation ◽  
Small Scale ◽  
Outer Diameter ◽  
Cooling Performance ◽  
The Heat Transfer Coefficient

The objective of this work is to experimentally and numerically evaluate small-scale cryosurgery using an ultrafine cryoprobe. The outer diameter (OD) of the cryoprobe was 550 μm. The cooling performance of the cryoprobe was tested with a freezing experiment using hydrogel at 37 °C. As a result of 1 min of cooling, the surface temperature of the cryoprobe reached −35 °C and the radius of the frozen region was 2 mm. To evaluate the temperature distribution, a numerical simulation was conducted. The temperature distribution in the frozen region and the heat transfer coefficient was discussed.

scholarly journals Temperature log simulations in high-enthalpy boreholes

2019 ◽  
Vol 7 (1) ◽  
Author(s):  
Jia Wang ◽  
Fabian Nitschke ◽  
Maziar Gholami Korzani ◽  
Thomas Kohl
Keyword(s):  
Heat Transfer ◽  
Temperature Distribution ◽  
Temperature Gradient ◽  
Flow Rate ◽  
Fluid Loss ◽  
Flow Conditions ◽  
Flow Rates ◽  
High Enthalpy ◽  
Fluid Losses ◽  
Lateral Heat

Abstract Temperature logs have important applications in the geothermal industry such as the estimation of the static formation temperature (SFT) and the characterization of fluid loss from a borehole. However, the temperature distribution of the wellbore relies on various factors such as wellbore flow conditions, fluid losses, well layout, heat transfer mechanics within the fluid as well as between the wellbore and the surrounding rock formation, etc. In this context, the numerical approach presented in this paper is applied to investigate the influencing parameters/uncertainties in the interpretation of borehole logging data. To this end, synthetic temperature logs representing different well operation conditions were numerically generated using our newly developed wellbore simulator. Our models account for several complex operation scenarios resulting from the requirements of high-enthalpy wells where different flow conditions, such as mud injection with- and without fluid loss and shut-in, occur in the drill string and the annulus. The simulation results reveal that free convective heat transfer plays an important role in the earlier evolution of the shut-in-time temperature; high accuracy SFT estimation is only possible when long-term shut-in measurements are used. Two other simulation scenarios for a well under injection conditions show that applying simple temperature correction methods on the non-shut-in temperature data could lead to large errors for SFT estimation even at very low injection flow rates. Furthermore, the magnitude of the temperature gradient increase depends on the flow rate, the percentage of fluid loss and the lateral heat transfer between the fluid and the rock formation. As indicated by this study, under low fluid losses (< 30%) or relatively higher flow rates (> 20 L/s), the impact of flow rate and the lateral heat transfer on the temperature gradient increase can be ignored. These results provide insights on the key factors influencing the well temperature distribution, which are important for the choice of the drilling data to estimate SFT and the design of the inverse modeling scheme in future studies to determine an accurate SFT profile for the high-enthalpy geothermal environment.

Sign in / Sign up

Export Citation Format

Share Document