Axis-Switching Behavior of Liquid Jets Issued from Non-Circular Nozzles Under Low-Intermediate Pressure

2021 ◽  
Vol 37 (2) ◽  
pp. 367-378
Author(s):  
Lin Hua ◽  
Hong Li ◽  
Yue Jiang
Keyword(s):  
Deformation Process ◽  
High Speed ◽  
Sprinkler Irrigation ◽  
High Speed Photography ◽  
Irrigation Systems ◽  
Intermediate Pressure ◽  
Water Jets ◽  
Switching Phenomenon ◽  
Circular Jets ◽  
Axis Switching

HighlightsThe flow behavior of water jets discharged from different orifices was investigated.High-speed photography (HSP) was used to obtain surface structures and spread characteristics of water jets.The deformation process in axis switching related to the corner vortices effect of non-circular jets was researched by numerical simulation.The axis switching of non-circular jets enhances entrainment ability of the jet.ABSTRACT. Low-intermediate pressure sprinkler irrigation systems are important research topics in the field of water-saving irrigation. Non-circular nozzles improve spray uniformity at lower pressures and are key components of sprinkler irrigation systems. In this article, the behavior of discharged water jets from nozzles with circular, square, and equilateral triangular orifices designed with the same flow rate was investigated. High-speed photography (HSP) was used to capture jet characteristics in the near field (z<20D). The largest spread angle was obtained for the square jet, which was on average 37% larger than that of the circular jet. In addition, numerical simulations were performed to analyze the axis-switching process using the large-eddy simulation (LES) method and the coupled level-set and volume of fluid (CLSVOF) method. The axis-switching phenomenon was observed in non-circular jets, in which surrounding air mixed with the jet and promoted the formation of thin diaphragm structures. The deformation process that occurs in axis switching is described according to the simulated vorticity and velocity fields. The research results suggest the axis-switching phenomenon is induced by corner vortex motions produced by the polygonal orifice, which accelerate the decay of the axial velocity and increase the jet entrainment rate. Thus, the effect of corner vortices should be considered in the design of polygonal nozzles. Keywords: Axis switching, High-speed photography, Liquid jet, Low-intermediate pressure sprinkler irrigation, Non-circular nozzle, Numerical simulation.

Comparative study on interfacial oscillations of rectangular and elliptical liquid jets

2020 ◽  
Vol 234 (7) ◽  
pp. 1272-1286 ◽  
Author(s):  
Amin Jaberi ◽  
Mehran Tadjfar
Keyword(s):  
Aspect Ratio ◽  
Weber Number ◽  
High Speed ◽  
Nozzle Geometry ◽  
Liquid Jets ◽  
High Speed Photography ◽  
Aspect Ratios ◽  
Water Jets ◽  
Switching Phenomenon ◽  
Axis Switching

The instability characteristics and flow structures of water jets injected from rectangular and elliptical nozzles with aspect ratios varying from 2 to 6 were experimentally studied and compared. Shadowgraph technique was employed for flow visualization, and structures on the liquid jet surface were captured using high speed photography. It was found that disturbances originating from the nozzle geometry initially perturbed the liquid column, and then, at high jet velocities, disturbances generated within the flow dominated the jet surface. It was also found that rectangular nozzles introduced more disturbances into the flow than the elliptical ones. The characteristic parameters of axis-switching phenomenon including wavelength, frequency, and amplitude were measured and compared. Axis-switching wavelength was found to increase linearly with Weber number. Also, the wavelengths of rectangular jets were longer than the elliptical jets. Further, the frequency of axis-switching was shown to be reduced with increase of both Weber number and aspect ratio. It was observed that the axis-switching amplitude increased monotonically, reached a peak, and then decreased gradually. It was also found that the axis-switching amplitude varied with Weber number. At lower values of Weber number, the rectangular nozzles had higher amplitude than the elliptical nozzles. However, at higher values of Weber number, this relation was reversed, and the elliptical nozzles had the higher axis-switching amplitudes. This reversal Weber number decreased with the orifice aspect ratio. The reversal Weber number for aspect ratio of 4 was about 289, and it had decreased to 144 for the aspect ratio of 6.

Hydraulic Performance and Jet Breakup Characteristics of the Impact Sprinkler with Circular and Non-circular Nozzles

2019 ◽  
Vol 35 (6) ◽  
pp. 911-924 ◽  
Author(s):  
Yue Jiang ◽  
Hong Li ◽  
Chao Chen ◽  
Lin Hua ◽  
Daming Zhang
Keyword(s):  
High Speed ◽  
Cone Angle ◽  
Hydraulic Performance ◽  
High Speed Photography ◽  
Breakup Process ◽  
Breakup Length ◽  
Jet Breakup ◽  
Circular Jets ◽  
Square Jets ◽  
The Impact

HighlightsThe hydraulic performance of the impact sprinkler with circular and non-circular nozzles were measured.A High-Speed Photography (HSP) technique was employed to extract the jet breakup process of the impact sprinkler.Two index equations of jet characteristic lengths and equivalent diameters of non-circular nozzles were fitted. Abstract. An experiment was carried out to investigate the hydraulic performance of an impact sprinkler by using circular and non-circular nozzles. A High-Speed Photography (HSP) technique was employed to extract the breakup process and flow behavior of low-intermediate pressure water jets issued from the different types of orifices. These orifices were selected by the principle of equal flowrate with the same pressure. Moreover, two characteristic lengths: the jet breakup length and the initial amplitude of surface wave were measured. It was found that the sprinkler with circular nozzles produced the largest radius of throw followed by square nozzles and regular triangular nozzles when the cone angle of nozzle and pressure were unchanged, while the sprinkler with regular triangular nozzle had the best variation trend of water distribution and combination uniformity coefficient. Regular triangular jets exhibited a higher degree in breakup and the shortest breakup length compared with the square jets and the circular jets. The initial amplitudes of surface waves of regular triangular jets were larger than the square jets and the circular jets with the same cone angle. Two index equations of jet characteristic lengths and equivalent diameters of both circular and non-circular orifices were fitted with a relative error of less than 10%, which means the fitting formulas were accurate. Keywords: Breakup length, Fitting formula, Hydraulic performance, Initial amplitude, Non-circular jets.

Use of a liquid shock tube as a device for the study of material deformation under impulsive loading conditions

2004 ◽  
Vol 218 (1) ◽  
pp. 39-51 ◽  
Author(s):  
B W Skews ◽  
O E Kosing ◽  
R J Hattingh
Keyword(s):  
Shock Tube ◽  
Deformation Process ◽  
High Speed ◽  
Pressure Pulse ◽  
Applied Pressure ◽  
Impulsive Loading ◽  
High Speed Photography ◽  
Material Deformation ◽  
Metal Plates ◽  
Versatile Tool

The deformation of metal plates and tubes achievable through the use of liquid shock waves generated in a shock tube is studied, with reference to both free-forming and forming the metal into dies, as well as to imprinting detailed features. The process is highly controllable, in terms of the magnitude and duration of the applied pressure pulse. A projectile is fired into a liquid column producing a high-pressure liquid shock wave which impinges on the testpiece. Different projectile materials, driving pressures and impact velocities are used to alter the energy and impulse transmitted. A particular attraction of its use in a laboratory is the application of high-speed photography to the deformation process. Illustration of the application of the facility to slamming studies and to fracture of brittle materials is included. It is concluded that the techniques employed offer a useful and versatile tool for many studies of material deformation.

Behavior of Soft Spheres During Impact by High-Speed Photography

1983 ◽  
Vol 105 (1) ◽  
pp. 67-73 ◽  
Author(s):  
Yoichi Tatara
Keyword(s):  
Deformation Process ◽  
High Speed ◽  
High Impact ◽  
High Speed Photography ◽  
Tennis Ball ◽  
Hertz Model ◽  
Hertz Theory ◽  
Soft Spheres ◽  
Almost All ◽  
The Impact

Previously, it has been verified experimentally for durations of impact that the Hertz theory (the quasi-statical theory) holds during impact of spheres without any exception. However, no measurement of duration of impact has been presented for spheres of materials other than metal. This study presents exceptional cases of impacts of spheres during which the Hertz model does not directly hold. By the use of a high-speed camera running at a speed of 5000 frames/s, durations of impact are measured directly for impacts of two solid rubber spheres of the same size and content and impacts of a soft ball (Japanese type-soft tennis ball) on a rigid foundation. As a result, the measured durations of impact in the two impacting cases are found to be decreased as the impact velocity is increased, similar in tendency to durations of impact of elastic metal spheres during which the Hertz theory holds. However, the measured durations of impact are found to be clearly shorter than results calculated according to the Hertz theory, approximately half in the former impacts at high impact velocities, and about 70 percent of the Hertzian results in the latter impacts at almost all impact velocities. Deformation process of the ball impacting on the foundation is also presented to indicate both durations in the compressive process and the restitution one to be shorter than those expected by the Hertz theory. The other results observed on the films are noted to investigate the origin of the great discrepancies between the measured and Hertzian durations (that is, the impacting mechanism of the rubber spheres or the rubber ball packed with air treated here).

Experimental Study on Jet Breakup Morphologies and Jet Characteristic Parameters of Non-circular Nozzles under Low-intermediate Pressures

2019 ◽  
Vol 35 (4) ◽  
pp. 617-632
Author(s):  
Yue Jiang ◽  
Hong Li ◽  
Lin Hua ◽  
Daming Zhang ◽  
Zakaria Issaka
Keyword(s):  
Surface Wave ◽  
High Speed ◽  
Flow Behavior ◽  
Initial Section ◽  
Droplet Formation ◽  
High Speed Photography ◽  
Breakup Length ◽  
Jet Breakup ◽  
Circular Jets ◽  
Pressure Water

Abstract. A High-Speed Photography (HSP) technique was used to investigate the breakup process and flow behavior of low-intermediate pressure water jets issued from square and triangular shaped nozzles. The non-circular orifices were designed based on the principle of equal flowrate with the same pressure in relation to the circular orifice. The breakup morphologies and boundary structures of the jets were studied under different nozzles and working pressures. Two forms of droplet formation and the process of droplet formation, in addition to the jet breakup lengths, initial amplitudes of surface waves and jet diffusion angles of different nozzles were evaluated. It was found that the jet presented a good continuity and fluidity in the initial section, and the fluid bands gradually appeared due to the air resistance and the jet break up as the disturbance intensifies. The degree of jet breakup was enhanced with the increase of pressure and cone nozzle angle. The random appearance of the fluid band structures and the dactylitic textures near the nozzles for non-circular jets appeared earlier than those produced by the circular jets. The small satellite droplets with different shapes and sizes were seen inside and outside the jet interface. Triangular jets exhibited the shortest breakup length, the initial amplitude of surface wave, and the diffusion angle of the jet at the same pressure were largest compared with square and circular jets. Two index equations of jet characteristic lengths and equivalent diameters of both circular and non-circular nozzles were fitted with a relative error of less than 10%, which means the fitting formulas are accurate. Keywords: Breakup length, High-speed photography, MATLAB simulation, Non-circular nozzle, Surface wave amplitude.

Flow Characteristics of Water Jets Discharging From Rectangular and Elliptical Injectors

2018 ◽  
Author(s):  
Amin Jaberi ◽  
Mehran Tadjfar
Keyword(s):  
Weber Number ◽  
Flow Characteristics ◽  
Maximum Amplitude ◽  
Qualitative Description ◽  
Jet Flows ◽  
Reference Case ◽  
Cross Sectional ◽  
Water Jets ◽  
Switching Phenomenon ◽  
Axis Switching

The flow and breakup characteristics of water jets issuing from rectangular and elliptical injectors into still atmosphere were experimentally compared. Injectors were of the same cross-sectional area and a circular injector was also employed as the reference case. Digital images taken by a diffused backlight technique were processed to extract the main characteristics of the jet column at different jet velocities. The measurements were carried out for mass flow rates varying from 2 L/h to 120 L/h with small enough steps at low speeds to capture Rayleigh regime. Aside from the qualitative description of the jet flows, stability curve was plotted to make a comparison between different jets. The comparison revealed that the ellipse jet is the first one to reach the critical Weber number, while the circular jet remains laminar at higher velocities than the other two jets. Moreover, axis-switching phenomenon was carefully studied as the common characteristic of rectangular and elliptical jets. The wavelength and maximum amplitude of axis-switching were measured at different flow conditions and the results were compared. Though the axis-switching wavelength of both jets demonstrated a linear increment with Weber number, the rectangular jet was found to increase with a higher slope. Furthermore, the non-dimensional maximum amplitude of axis-switching showed an approximate behavior.

Entrance length effects on the flow features of rectangular liquid jets

2020 ◽  
pp. 095441002096844
Author(s):  
MH Aliyoldashi ◽  
M Tadjfar ◽  
A Jaberi
Keyword(s):  
Experimental Study ◽  
High Speed ◽  
Liquid Surface ◽  
Fluid Flows ◽  
Liquid Jets ◽  
High Speed Photography ◽  
Entrance Length ◽  
Flow Features ◽  
Flow Visualizations ◽  
Axis Switching

An experimental study was carried out to investigate the effects of entrance length on the main characteristics of rectangular liquid jets discharged into the stagnant atmosphere. Six rectangular nozzles, all with the same aspect ratio of 3 but with different entrance length ratios ranging from 3.3 to 60 were constructed. The physics of the fluid flows was visualized by the aid of backlight shadowgraph technique and high speed photography. Flow visualizations revealed that in the mid-range of Weber numbers, the perturbations induced over the liquid surface remarkably depended on the entrance length ratio. Moreover, the characteristics of the axis-switching instability of rectangular liquid jets were measured. It was found that axis-switching wavelength was independent of the entrance length, while the amplitude of axis-switching was directly influenced. For entrance length ratios smaller than 10, the amplitude was increased with increase of entrance length, whereas for entrance length ratios higher than 10, this trend was reversed. Measurements of breakup length also showed that the transition of flow regimes was not perceptibly affected by the entrance length.

Characteristics of Impinging Water Jet Discharged From a Central-Body Nozzle

2011 ◽  
Author(s):  
Can Kang ◽  
Liang Zhou ◽  
Weifeng Wang ◽  
Haixia Liu
Keyword(s):  
High Speed ◽  
Central Body ◽  
Water Jet ◽  
Wake Flow ◽  
Outlet Section ◽  
High Speed Photography ◽  
Nozzle Outlet ◽  
Water Jets ◽  
Through Flow ◽  
Computational Fluid Dynamics Cfd

Submerged water jet discharged from a central-body nozzle was investigated through flow visualization, numerical simulation and impingement experiment. Under jet pressure of 15 MPa, three layout plans of central body were introduced and corresponding water jets were visualized by using high speed photography technique. Cavitating jet flow fields were simulated with commercial computational fluid dynamics (CFD) software Fluent which employs full cavitation model. Sandstone cuboid was used as the sample workpiece exposed to the submerged water jet of 15MPa. It is proved that cavitation tone exist in the wake flow after the central body. When the end cross-section of the central body is parallel with the nozzle outlet section, the largest axial length of cavitation zone is obtained. Compared with round water jet with the same equivalent nozzle outlet area, the central-body nozzle yields stronger impinging effect.

Waves on water jets

1977 ◽  
Vol 83 (1) ◽  
pp. 119-127 ◽  
Author(s):  
J. W. Hoyt ◽  
J. J. Taylor
Keyword(s):  
Reynolds Number ◽  
Nozzle Exit ◽  
High Speed ◽  
High Reynolds Number ◽  
High Speed Photography ◽  
Axisymmetric Mode ◽  
Spray Formation ◽  
Water Jets ◽  
High Reynolds ◽  
Axisymmetric Disturbances

By the use of high-speed photography, instabilities occurring in high Reynolds number water jets discharging into air have been made visible. These instabilities include the axisymmetric mode accompanying the transition from laminar to turbulent flow at the nozzle exit, spray formation as a culmination of the axisymmetric disturbances, and, further downstream, helical disturbances which result in the entire jet assuming a helical form. The final disruption of the jet is due to amplification of the helical waves. It is further shown that the amplification of the helical disturbances is due in part to aerodynamic form drag, since jets discharging into surrounding air moving at the same speed as the jet remain relatively stable, compared with the case when the jet is discharged into stagnant air.

Sign in / Sign up

Export Citation Format

Share Document