Research on the Beam Damage Diagnosis Method for a High-Speed Transplanter Based on the Strain Mode

2021 ◽  
Vol 37 (1) ◽  
pp. 25-32
Author(s):  
Jiangtao Ji ◽  
Kaikang Chen ◽  
Xin Jin ◽  
Jing Pang ◽  
Xing Chen ◽  
...  
Keyword(s):  
Mode Shape ◽  
High Speed ◽  
Operating Conditions ◽  
Agricultural Machinery ◽  
Damage Diagnosis ◽  
Change Rate ◽  
Strain Mode ◽  
Mode Change ◽  
Displacement Mode ◽  
Beam Damage

Abstract. The vibration of agricultural machinery significantly influences driving comfort and operation reliability. In recent years, research on the vibrational characteristics of agricultural machinery has gradually expanded. To solve the problem of the obvious vibration of a high-speed transplanter under operating conditions, this article examines the method of beam damage diagnosis for high-speed transplanters based on the strain mode. Based on the modal theory, the displacement and strain modal analysis of the beam of the high-speed transplanter is performed. The analysis shows that the relative deviation of the modal frequencies of the same order before and after the beam is damaged is small. There is no obvious abrupt change in the displacement mode shape, while the strain mode shape has a sudden change peak after the beam is damaged. Thus, the strain mode change rate is constructed as a diagnostic index for beam damage. The analysis results show that the strain mode change rate increases with the increase in beam damage degree. Finally, the least squares method is used to fit the corresponding relationship between the two quantities. The results show that the strain mode change rate is sensitive and reliable as an index of damage diagnosis, which can better determine the location and degree of damage to the beam. Keywords: Beam, Damage, Diagnosis, Rice transplanter, Strain mode.

Research on Structural Damage Diagnosis Based on Strain Modal

2013 ◽  
Vol 438-439 ◽  
pp. 739-742
Author(s):  
Yi Na Zhang ◽  
Lei Cao
Keyword(s):  
Damage Detection ◽  
Cantilever Beam ◽  
Theoretical Basis ◽  
Structural Damage ◽  
Damage Identification ◽  
Damage Diagnosis ◽  
Strain Mode ◽  
Engineering Structure ◽  
Displacement Mode ◽  
Analysis Theory

The damage diagnosis theory and method of engineering structure is one of the hot issues concerned by the engineering circles at present. Based on the strain modal analysis theory, it expounds the connection among displacement mode, strain mode and curvature mode, with a heavy rubber as the material to make a cantilever beam, and establishing the different damage conditions of the cantilever beam, studying about dynamic structural damage identification under the incentive, which provides the theoretical basis and technical support for the research on damage detection of large engineering structure.

Dual-type sensor placement optimization by fully utilizing structural modal information

2018 ◽  
Vol 22 (3) ◽  
pp. 737-750 ◽  
Author(s):  
Xue-Yang Pei ◽  
Ting-Hua Yi ◽  
Hong-Nan Li
Keyword(s):  
Mode Shape ◽  
Sensor Placement ◽  
Estimation Method ◽  
Mode Shapes ◽  
Strain Gauges ◽  
Shape Estimation ◽  
Modal Assurance Criterion ◽  
Strain Mode ◽  
Placement Method ◽  
Displacement Mode

Strain gauges and accelerometers are widely used in bridge structural health monitoring systems. Generally, the strain gauges are placed on the key locations to obtain local structural deformation information; the accelerometers are used to obtain the structural modal information. However, the modal information contained in the measured strains is not taken into account. In this article, to fully utilize the modal information contained in strains, a mode shape estimation method is proposed that the strain mode shapes of the strain locations are used to obtain the displacement mode shapes of some positions without accelerometers. At first, to simulate the practical situation, some positions with large structural deformations are selected as the strain gauge locations. Using the proposed mode shape estimation method, the displacement mode shapes of some locations without accelerometers are estimated by the strain mode shapes using the least squares method, and the locations with the smallest estimation error are finally determined as the estimated locations. Then, accelerometers are added to the existing sensor placement. Here, the modal assurance criterion is used to evaluate the distinguishability of the displacement mode shapes obtained from the strain gauges and accelerometers. The accelerometer locations that bring the smallest modal assurance criterion values are selected. In addition, a redundancy can be set to avoid the adjacent sensors containing similar modal information. Through the proposed sensor placement method, the deformation and modal information contained in the strain gauges is fully utilized; the modal information contained in the strain gauges and accelerometers is comprehensively utilized. Numerical experiments are carried out using a bridge benchmark structure to demonstrate the sensor placement method.

scholarly journals The Influence of Carrier Air Preheating on Autoignition of Inline-Injected Hydrogen–Nitrogen Mixtures in Vitiated Air of High Temperature

2017 ◽  
Vol 140 (3) ◽  
Author(s):  
Christoph A. Schmalhofer ◽  
Peter Griebel ◽  
Manfred Aigner
Keyword(s):  
Hydrogen Content ◽  
Gas Turbines ◽  
High Speed ◽  
Flame Stabilization ◽  
Operating Conditions ◽  
Promoting Effect ◽  
Experimental Conditions ◽  
Lean Premixed Combustion ◽  
Image Velocimetry ◽  
Fuel Mixtures

The use of highly reactive hydrogen-rich fuels in lean premixed combustion systems strongly affects the operability of stationary gas turbines (GT) resulting in higher autoignition and flashback risks. The present study investigates the autoignition behavior and ignition kernel evolution of hydrogen–nitrogen fuel mixtures in an inline co-flow injector configuration at relevant reheat combustor operating conditions. High-speed luminosity and particle image velocimetry (PIV) measurements in an optically accessible reheat combustor are employed. Autoignition and flame stabilization limits strongly depend on temperatures of vitiated air and carrier preheating. Higher hydrogen content significantly promotes the formation and development of different types of autoignition kernels: More autoignition kernels evolve with higher hydrogen content showing the promoting effect of equivalence ratio on local ignition events. Autoignition kernels develop downstream a certain distance from the injector, indicating the influence of ignition delay on kernel development. The development of autoignition kernels is linked to the shear layer development derived from global experimental conditions.

Feasibility of High Speed Furnace Drawing of Optical Fibers

2004 ◽  
Vol 126 (5) ◽  
pp. 852-857 ◽  
Author(s):  
Xu Cheng ◽  
Yogesh Jaluria
Keyword(s):  
Optical Fibers ◽  
High Speed ◽  
Flow Instability ◽  
Fiber Quality ◽  
Domain Boundary ◽  
Operating Conditions ◽  
Furnace Temperature ◽  
Fiber Drawing ◽  
Heated Zone ◽  
Additional Information

The domain of operating conditions, in which the optical fiber-drawing process is successful, is an important consideration. Such a domain is mainly determined by the stresses acting on the fiber and by the stability of the process. This paper considers an electrical resistance furnace for fiber drawing and examines conditions for process feasibility. In actual practice, it is known that only certain ranges of furnace temperature and draw speed lead to successful fiber drawing. The results obtained here show that the length of the heated zone and the furnace temperature distribution are other important parameters that can be varied to obtain a feasible process. Physical behavior close to the boundary of the feasible domain is also studied. It is found that the iterative scheme for neck-down profile determination diverges rapidly when the draw temperature is lower than that at the acceptable domain boundary due to the lack of material flow. However, the divergence rate becomes much smaller as the temperature is brought close to the domain boundary. Additional information on the profile determination as one approaches the acceptable region is obtained. It is found that it is computationally expensive and time-consuming to locate the exact boundary of the feasible drawing domain. From the results obtained, along with practical considerations of material rupture, defect concentration, and flow instability, an optimum design of a fiber-drawing system can be obtained for the best fiber quality.

Characteristics of air entrainment during dynamic wetting failure along a planar substrate

2014 ◽  
Vol 747 ◽  
pp. 119-140 ◽  
Author(s):  
E. Vandre ◽  
M. S. Carvalho ◽  
S. Kumar
Keyword(s):  
High Speed ◽  
Water Solution ◽  
Air Entrainment ◽  
Dynamic Contact ◽  
Operating Conditions ◽  
Dynamic Wetting ◽  
Glycerol Water ◽  
Planar Substrate ◽  
Wide Range ◽  
Stationary Plate

AbstractCharacteristic substrate speeds and meniscus shapes associated with the onset of air entrainment are studied during dynamic wetting failure along a planar substrate. Using high-speed video, the behaviour of the dynamic contact line (DCL) is recorded as a tape substrate is drawn through a bath of a glycerol/water solution. Air entrainment is identified by triangular air films that elongate from the DCL above some critical substrate speed. Meniscus confinement within a narrow gap between the substrate and a stationary plate is shown to delay air entrainment to higher speeds for a wide range of liquid viscosities, expanding upon the findings of Vandre, Carvalho & Kumar (J. Fluid Mech., vol. 707, 2012, pp. 496–520). A pressurized liquid reservoir controls the meniscus position within the confinement gap. It is found that liquid pressurization further postpones air entrainment when the meniscus is located near a sharp corner along the stationary plate. Meniscus shapes recorded near the DCL demonstrate that operating conditions influence the size of entrained air films, with smaller films appearing in the more viscous solutions. Regardless of size, air films become unstable to thickness perturbations and ultimately rupture, leading to the entrainment of air bubbles. Recorded critical speeds and air-film sizes compare well to predictions from a hydrodynamic model for dynamic wetting failure, suggesting that strong air stresses near the DCL trigger the onset of air entrainment.

On-Road Gaseous Emission Characteristics of China IV CNG Bus in Shanghai

2013 ◽  
Vol 690-693 ◽  
pp. 1864-1871 ◽  
Author(s):  
Di Ming Lou ◽  
Si Li Qian ◽  
Zhi Yuan Hu ◽  
Pi Qiang Tan
Keyword(s):  
Emission Factor ◽  
High Speed ◽  
Idle Time ◽  
Operating Conditions ◽  
Vehicle Emission ◽  
Emission Characteristics ◽  
Emission Measurement ◽  
Gaseous Emissions ◽  
Average Speed ◽  
Portable Emission Measurement System

In this paper, on-road CO, THC, NOX, CO2 gaseous emissions characteristics of china IV CNG bus were analyzed based on on-road vehicle emission test in the peak and non-peak hours of city traffic in Shanghai using a portable emission measurement system (PEMS). The experimental results reveal that: compared with the condition results in the non-peak hours, it (conditions in the peak hours) have lower average speed, longer idle time and shorter high speed time; the NOX emission factor and rate in the peak hour reduced by 5.66% and 70.2%; the CO, HC, CO2 emissions factors are increased by 47.2%, 32.6%, 20.8%, and the CO, HC, CO2 emissions rates reduced by 1.94%, 26.5%, 48.7% respectively, compared with that in the non-peak hours; The CO, HC, NOX, CO2 emissions factors all decreased as bus speed increased, while they increased as bus acceleration increased; the gaseous emissions rates all increased as bus speed increased; both the emissions factors and emissions rates contributions are highest at accelerations, higher at cruise speeds, and the lowest at decelerations for non-idling buses; the emissions rates under the condition of idling is lowest; gaseous emissions contribution under the various operating conditions has displayed certain correlations with the percentage of the time for different operating conditions.

Experimental Inverstigations On the Pressure Fluctuations in the Sealing Gap of Dry Gas Seals with Embedded Pressure Sensors

2021 ◽  
Author(s):  
Jingjing Luo ◽  
Dieter Brillert
Keyword(s):  
High Speed ◽  
Gas Flow ◽  
Static Pressure ◽  
Pressure Sensors ◽  
Operating Conditions ◽  
Test Facility ◽  
Experimental Investigations ◽  
Mechanical Seals ◽  
Process Gas ◽  
Sealing Gap

Abstract Dry gas lubricated non-contacting mechanical seals (DGS), most commonly found in centrifugal compressors, prevent the process gas flow into the atmosphere. Especially when high speed is combined with high pressure, DGS is the preferred choice over other sealing alternatives. In order to investigate the flow field in the sealing gap and to facilitate the numerical prediction of the seal performance, a dedicated test facility is developed to carry out the measurement of key parameters in the gas film. Gas in the sealing film varies according to the seal inlet pressure, and the thickness of gas film depends on this fluctuated pressure. In this paper, the test facility, measurement methods and the first results of static pressure measurements in the sealing gap of the DGS obtained in the described test facility are presented. An industry DGS with three-dimensional grooves on the surface of the rotating ring, where experimental investigations take place, is used. The static pressure in the gas film is measured, up to 20 bar and 8,100 rpm, by several high frequency ultraminiature pressure transducers embedded into the stationary ring. The experimental results are discussed and compared with the numerical model programmed in MATLAB, the characteristic and magnitude of which have a good agreement with the numerical simulations. It suggests the feasibility of measuring pressure profiles of the standard industry DGS under pressurized dynamic operating conditions without altering the key components of the seal and thereby affecting the seal performance.

Influence of the Variation of Plasma Torch Parameters on Particle Melting and Solidification

1997 ◽  
Author(s):  
M. Vardelle ◽  
P. Fauchais ◽  
A. Vardelle ◽  
A.C. Léger
Keyword(s):  
Flow Rate ◽  
High Speed ◽  
Gas Flow ◽  
Operating Conditions ◽  
Characteristic Parameters ◽  
Powder Mass ◽  
Arc Current ◽  
Plasma Sprayed ◽  
Carrier Gas Flow ◽  
Melting And Solidification

Abstract A study of the flattening and cooling of particles plasma-sprayed on a substrate is presented. The characteristic parameters of the splats are linked to the parameters of the impacting particles by using an experimental device consisting of a phase Doppler particle analyzer and a high-speed pyrometer. However, during the long experiments required to get reliable correlations, it was observed that variations in plasma spray operating conditions may alter the particles behavior in the plasma jet. Therefore, a simple and easy-to-use system was developed to control in real time the spray jet. In this paper, the effect of carrier gas flow rate, arc current and powder mass flow rate is investigated. The results on zirconia and alumina powders show the capability of the technique to sense the particle spray position and width.

Structural Shape Reconstruction of FBG Flexible Plate Using Modal Superposition Method

2017 ◽  
Author(s):  
Li Li ◽  
Ben S. Zhong ◽  
Zi Y. Geng ◽  
Wei Sun
Keyword(s):  
Mode Shape ◽  
Shape Reconstruction ◽  
Displacement Sensor ◽  
Superposition Method ◽  
Flexible Plate ◽  
Structural Shape ◽  
Modal Superposition ◽  
Displacement Mode ◽  
Modal Superposition Method ◽  
Strain Data

Structural shape reconstruction is a critical issue for real-time structural health monitoring in the fields of engineering application. This paper shows how to implement structural shape reconstruction using a small number of strain data measured by fiber Bragg grating (FBG) sensors. First, the basic theory of structural shape reconstruction is introduced using modal superposition method. A transformation is derived from the measured discrete strain data to global displacement field through modal coordinate, which is the same for strain mode shape superposition and displacement mode shape superposition. Then, optimization of the sensor layout is investigated to achieve the effective reconstruction effect. Finally, structural shape reconstruction algorithm using modal superposition method is applied in experiments. The experiment results show that the reconstructed displacements match well with those measured by a laser displacement sensor and the proposed approach is a promising method for structural shape reconstruction.

Sign in / Sign up

Export Citation Format

Share Document