Turbulence Intensity as Influenced by Surface Roughness and Mean Velocity in a Wind-Tunnel Boundary Layer

1971 ◽  
Vol 14 (2) ◽  
pp. 0285-0289 ◽  
Author(s):  
Leon Lyles ◽  
Lowell A. Disrud ◽  
and R. K. Krauss
Keyword(s):  
Boundary Layer ◽  
Surface Roughness ◽  
Wind Tunnel ◽  
Turbulence Intensity ◽  
Mean Velocity

Measurement of Transitional Surface Roughness Effects on Flat-Plate Boundary Layer Transition

2019 ◽  
Vol 141 (7) ◽  
Author(s):  
Heechan Jeong ◽  
Seung Woo Lee ◽  
Seung Jin Song
Keyword(s):  
Boundary Layer ◽  
Surface Roughness ◽  
Turbulence Intensity ◽  
Plate Boundary ◽  
Boundary Layer Transition ◽  
Mean Velocity ◽  
Layer Transition ◽  
Turbulence Intermittency ◽  
Transition Length ◽  
Flat Plate Boundary Layer

An experimental study has been conducted to investigate the effects of transitionally rough surface on the flat-plate boundary layer transition. Transitional boundary layers with three different flat plates (ks+ = 0.07 ∼ 0.19, 2.71 ∼ 7.05, and 13.65 ∼ 41.09) have been measured with a single-sensor hot-wire probe. All of the measurements have been conducted under zero pressure gradient (ZPG) at the fixed Reynolds number (ReL) and freestream turbulence intensity (Tu) of 3.05 × 106 and 0.2%. Transitionally, rough surface does not affect the sigmoidal distribution of turbulence intermittency model; but induces earlier transition onset and shortens the transition length. For all surfaces, streamwise turbulence intensity profiles with similar values of turbulence intermittency are similar for the transition length less than 60%. Therefore, mean velocity profiles with the similar values of turbulence intermittency are similar regardless of surface conditions. However, downstream of 60% of the transition length, mean velocity defect increases as the surface roughness increases. Enhanced diffusion of turbulent kinetic energy from the near wall (y/δ < 0.1) to the outer part (y/δ ≈ 0.4) of the boundary layer due to the surface roughness is responsible for the increased momentum deficit.

Measurements in a Turbulent Boundary Layer Over a d-Type Surface Roughness

1975 ◽  
Vol 42 (3) ◽  
pp. 591-597 ◽  
Author(s):  
D. H. Wood ◽  
R. A. Antonia
Keyword(s):  
Boundary Layer ◽  
Surface Roughness ◽  
Turbulent Boundary Layer ◽  
Turbulent Energy ◽  
Shear Stresses ◽  
Normal Velocity ◽  
Mean Velocity ◽  
Outer Flow ◽  
Intensity Measurements ◽  
Normal And Shear Stresses

Mean velocity and turbulence intensity measurements have been made in a fully developed turbulent boundary layer over a d-type surface roughness. This roughness is characterised by regular two-dimensional elements of square cross section placed one element width apart, with the cavity flow between elements being essentially isolated from the outer flow. The measurements show that this boundary layer closely satisfies the requirement of exact self-preservation. Distribution across the layer of Reynolds normal and shear stresses are closely similar to those found over a smooth surface except for the region immediately above the grooves. This similarity extends to distributions of third and fourth-order moments of longitudinal and normal velocity fluctuations and also to the distribution of turbulent energy dissipation. The present results are compared with those obtained for a k-type or sand grained roughness.

Turbulent Boundary Layer Subjected to a Sudden Change in Surface Roughness and Temperature

1999 ◽  
Author(s):  
João Henrique D. Guimarães ◽  
Sergio J. F. dos Santos ◽  
Jian Su ◽  
Atila P. Silva Freire
Keyword(s):  
Boundary Layer ◽  
Surface Roughness ◽  
Turbulent Boundary Layer ◽  
Skin Friction ◽  
Sudden Change ◽  
Stanton Number ◽  
Temperature Profiles ◽  
Internal Layers ◽  
Mean Velocity ◽  
Wall Boundary Conditions

Abstract In present work, the dynamic and thermal behaviour of flows that develop over surfaces that simultaneously present a sudden change in surface roughness and temperature are discussed. In particular, the work is concerned with the physical validation of a newly proposed formulation for the near wall temperature profile. The theory uses the concept of the displacement in origin, together with some asymptotic arguments, to propose a new expression for the logarithmic region of the turbulent boundary layer. The new expressions are, therefore, of universal applicability, being independent of the type of rough surface considered. The present formulation may be used to give wall boundary conditions for two-equation differential models. The theoretical results are validated with experimental data obtained for flows that develop over flat surfaces with sudden changes in surface roughness and in temperature conditions. Measurements of mean velocity and of mean temperature are presented. A reduction of the data provides an estimate of the skin-friction coefficient, the Stanton number, the displacement in origin for both the velocity and the temperature profiles, and the thickness of the internal layers for the velocity and temperature profiles. The skin-friction co-efficient was calculated based on the chart method of Perry and Joubert (J.F.M., 17, 193–211, 1963) and on a balance of the integral momentum equation. The same chart method was used for the evaluation of the Stanton number and the displacement in origin.

scholarly journals Blind test comparison of the performance and wake flow between two in-line wind turbines exposed to different atmospheric inflow conditions

2016 ◽  
Author(s):  
Jan Bartl ◽  
Lars Sætran
Keyword(s):  
Wind Tunnel ◽  
Wind Turbines ◽  
Turbulence Intensity ◽  
Wake Flow ◽  
Detached Eddy Simulation ◽  
Mean Velocity ◽  
Blind Test ◽  
The Mean ◽  
Inlet Conditions ◽  
Inflow Conditions

Abstract. This is a summary of the results of the fourth Blind test workshop which was held in Trondheim in October 2015. Herein, computational predictions on the performance of two in-line model wind turbines as well as the mean and turbulent wake flow are compared to experimental data measured at NTNU's wind tunnel. A detailed description of the model geometry, the wind tunnel boundary conditions and the test case specifications was published before the workshop. Expert groups within Computational Fluid Dynamics (CFD) were invited to submit predictions on wind turbine performance and wake flow without knowing the experimental results at the outset. The focus of this blind test comparison is to examine the model turbines' performance and wake development up until 9 rotor diameters downstream at three different atmospheric inflow conditions. Besides a spatially uniform inflow field of very low turbulence intensity (TI = 0.23 %) as well as high turbulence intensity (TI = 10.0 %), the turbines are exposed to a grid-generated atmospheric shear flow (TI = 10.1 %). Five different research groups contributed with their predictions using a variety of simulation models, ranging from fully resolved Reynolds Averaged Navier Stokes (RANS) models to Large Eddy Simulations (LES). For the three inlet conditions the power and the thrust force of the upstream turbine is predicted fairly well by most models, while the predictions of the downstream turbine's performance show a significantly higher scatter. Comparing the mean velocity profiles in the wake, most models approximate the mean velocity deficit level sufficiently well. However, larger variations between the models for higher downstream positions are observed. The prediction of the turbulence kinetic energy in the wake is observed to be very challenging. Both the LES model and the IDDES (Improved Delayed Detached Eddy Simulation) model, however, are consistently managing to provide fairly accurate predictions of the wake turbulence.

Surface roughness effect on rotor broadband noise

2018 ◽  
Vol 17 (4-5) ◽  
pp. 438-466 ◽  
Author(s):  
Baofeng Cheng ◽  
Yiqiang Han ◽  
Kenneth S Brentner ◽  
Jose Palacios ◽  
Philip J Morris ◽  
...  
Keyword(s):  
Boundary Layer ◽  
Surface Roughness ◽  
Turbulent Boundary Layer ◽  
Layer Thickness ◽  
Turbulence Intensity ◽  
Boundary Layer Thickness ◽  
Broadband Noise ◽  
Ice Accretion ◽  
Trailing Edge ◽  
Trailing Edge Noise

The change of helicopter rotor broadband noise due to different surface roughness during ice accretion is investigated. Comprehensive rotor broadband noise measurements are carried out on rotor blades with different roughness sizes and rotation speeds in two facilities: the Adverse Environment Rotor Test Stand facility at The Pennsylvania State University, and the University of Maryland Acoustic Chamber. In both facilities, the measured high-frequency broadband noise increases significantly with increasing surface roughness height. Rotor broadband noise source identification is conducted and the broadband noise related to ice accretion is thought to be turbulent boundary layer-trailing edge noise. Theory suggests turbulent boundary layer-trailing edge noise scales with Mach number to the fifth power, which is also observed in the experimental data confirming that the dominant broadband noise mechanism during ice accretion is trailing edge noise. A correlation between the ice-induced surface roughness and the broadband noise level is developed. The correlation is strong, which can be used as an ice accretion early detection tool for helicopters, as well as to quantify the ice-induced roughness at the early stage of rotor ice accretion. The trailing edge noise theories developed by Ffowcs Williams and Hall, and Howe both identify two important parameters: boundary layer thickness and turbulence intensity. Numerical studies of two-dimensional airfoils with different ice-induced surface roughness heights are conducted to investigate the extent that surface roughness impacts the boundary layer thickness and turbulence intensity (and ultimately the turbulent boundary layer-trailing edge noise). The results show that boundary layer thickness and turbulence intensity at the trailing edge increase with the increased roughness height. Using Howe’s trailing edge noise model, the increased sound pressure level of the trailing edge noise due to the increased displacement thickness and normalized integrated turbulence intensity are 6.2 and 1.6 dB for large and small accreted ice roughness heights, respectively. The estimated increased sound pressure level values agree reasonably well with the experimental results, which are 5.8 and 2.6 dB for large and small roughness height, respectively.

Investigation of Boundary Layer Flows Over a Flat Plate With Different-Size Transverse Square Grooves at s/w = 10

2007 ◽  
Author(s):  
Redha Wahidi ◽  
Walid Chakroun ◽  
Sami Al-Fahad
Keyword(s):  
Boundary Layer ◽  
Flat Plate ◽  
Skin Friction ◽  
Turbulence Intensity ◽  
Viscous Sublayer ◽  
Velocity Profiles ◽  
Boundary Layer Flows ◽  
Mean Velocity ◽  
Uncertainty Range ◽  
The Mean

Turbulent boundary layer flows over a flat plate with multiple transverse square grooves spaced 10 element widths apart were investigated. Mean velocity profiles, turbulence intensity profiles, and the distributions of the skin-friction coefficients (Cf) and the integral parameters are presented for two grooved walls. The two transverse square groove sizes investigated are 5mm and 2.5mm. Laser-Doppler Anemometer (LDA) was used for the mean velocity and turbulence intensity measurements. The skin-friction coefficient was determined from the gradient of the mean velocity profiles in the viscous sublayer. Distribution of Cf in the first grooved-wall case (5mm) shows that Cf overshoots downstream of the groove and then oscillates within the uncertainty range and never shows the expected undershoot in Cf. The same overshoot is seen in the second grooved-wall case (2.5mm), however, Cf continues to oscillate above the uncertainty range and never returns to the smooth-wall value. The mean velocity profiles clearly represent the behavior of Cf where a downward shift is seen in the Cf overshoot region and no upward shift is seen in these profiles. The results show that the smaller grooves exhibit larger effects on Cf, however, the boundary layer responses to these effects in a slower rate than to those of the larger grooves.

Some Observations on dr. Coleman's Comments

1957 ◽  
Vol 61 (557) ◽  
pp. 361-361
Author(s):  
G. V. Lachmann
Keyword(s):  
Boundary Layer ◽  
Surface Roughness ◽  
Reynolds Number ◽  
Wind Tunnel ◽  
Short Distance ◽  
Wind Tunnel Tests ◽  
Theoretical Methods ◽  
Unit Reynolds Number ◽  
Research Department ◽  
Boundary Layer Profile

The method referred to in Dr. Coleman's notes was developed with the collaboration of my colleague Mr. J. B. Edwards of Handley Page Research Department. The purpose was to obtain a rational estimate of suction quantities and suction distribution, linked up with measurements of boundary layer profiles and suction quantities on wind tunnel models, and also to assess the effect of a certain degree of roughness of the order to be expected on actual wings. Existing theoretical methods ignore roughness which, however, is a most important parameter not only in wind tunnel tests, but also in flight at higher values of the unit Reynolds number; surface roughness obviously limits the intensity of suction which can be applied at a spanwise suction strip.It was intuitively assumed that the removal of fluid by suction was equivalent to cutting off the lower portion of the boundary layer profile at the upstream edge of the suction strip and that a rapid re-adjustment of the boundary layer profile within a short distance took place.

Wind effects on rough-walled and smooth-walled large cooling towers

2016 ◽  
Vol 20 (6) ◽  
pp. 843-864 ◽  
Author(s):  
XX Cheng ◽  
L Zhao ◽  
YJ Ge ◽  
R Dong ◽  
C Demartino
Keyword(s):  
Boundary Layer ◽  
Surface Roughness ◽  
Wind Tunnel ◽  
Flow Field ◽  
Atmospheric Boundary Layer ◽  
Model Test ◽  
Full Scale ◽  
Cooling Towers ◽  
Test Results ◽  
Wind Effects

Adding vertical ribs is recognized as a useful practice for reducing wind effects on cooling towers. However, ribs are rarely used on cooling towers in China since Chinese Codes are insufficient to support the design of rough-walled cooling towers, and an “understanding” hampers the use of ribs, which thinks that increased surface roughness has limited effects on the maximum internal forces that control the structural design. To this end, wind tunnel model tests in both uniform flow field with negligible free-stream turbulence and atmospheric boundary layer (ABL) turbulent flow field are carried out in this article to meticulously study and quantify the surface roughness effects on both static and dynamic wind loads for the purpose of improving Chinese Codes first. Subsequently, a further step is taken to obtain wind effects on a full-scale large cooling tower at a high Re, which are employed to validate the results obtained in the wind tunnel. Finally, the veracity of the model test results is discussed by investigating the Reynolds number (Re) effects on them. It has been proved that the model test results for atmospheric boundary layer flow field are all obtained in the range of Re-independence and the conclusions drawn from model tests and full-scale measurements basically agree, so most model test results presented in this article can be directly applied to the full-scale condition without corrections.

The Effects of Surface Roughness on the Mean Velocity Profile in a Turbulent Boundary Layer

2002 ◽  
Vol 124 (3) ◽  
pp. 664-670 ◽  
Author(s):  
Donald J. Bergstrom ◽  
Nathan A. Kotey ◽  
Mark F. Tachie
Keyword(s):  
Boundary Layer ◽  
Surface Roughness ◽  
Turbulent Boundary Layer ◽  
Velocity Profile ◽  
Friction Velocity ◽  
Outer Region ◽  
Stream Velocity ◽  
Mean Velocity ◽  
Outer Flow ◽  
The Mean

Experimental measurements of the mean velocity profile in a canonical turbulent boundary layer are obtained for four different surface roughness conditions, as well as a smooth wall, at moderate Reynolds numbers in a wind tunnel. The mean streamwise velocity component is fitted to a correlation which allows both the strength of the wake, Π, and friction velocity, Uτ, to vary. The results show that the type of surface roughness affects the mean defect profile in the outer region of the turbulent boundary layer, as well as determining the value of the skin friction. The defect profiles normalized by the friction velocity were approximately independent of Reynolds number, while those normalized using the free stream velocity were not. The fact that the outer flow is significantly affected by the specific roughness characteristics at the wall implies that rough wall boundary layers are more complex than the wall similarity hypothesis would allow.

Sign in / Sign up

Export Citation Format

Share Document