scholarly journals Fluctuations in Pulse-Frequency of the Dorsal Vessel of Insects

1975 ◽  
Vol 19 (2) ◽  
pp. 70-78
Author(s):  
Kanji TACHIBANA
Keyword(s):  
Pulse Frequency ◽  
Dorsal Vessel

Demonstration of 6-bit, 0.20-mVpp Quasi-Triangle Voltage Waveform Generator Based on Pulse-Frequency Modulation

2014 ◽  
Vol E97.C (3) ◽  
pp. 194-197 ◽  
Author(s):  
Yoshitaka TAKAHASHI ◽  
Hiroshi SHIMADA ◽  
Masaaki MAEZAWA ◽  
Yoshinao MIZUGAKI
Keyword(s):  
Frequency Modulation ◽  
Pulse Frequency ◽  
Waveform Generator ◽  
Voltage Waveform ◽  
Pulse Frequency Modulation

INVESTIGATION OF PULSE FREQUENCY ON FUSION ZONE CHARACTERISTICS OF GTA WELDED AZ31B MAGNESIUM ALLOY JOINTS

2020 ◽  
Vol 15 (2) ◽  
Author(s):  
Subravel V
Keyword(s):  
Magnesium Alloy ◽  
Tensile Properties ◽  
Fusion Zone ◽  
Welding Speed ◽  
Pulse Frequency ◽  
Pulsed Current ◽  
Az31b Magnesium Alloy ◽  
Gas Tungsten Arc ◽  
Gas Tungsten ◽  
Different Levels

In this investigation an attempt has been made to study the effect of welding on fusion characteristics of pulsed current gas tungsten arc welded AZ31B magnesium alloy joints. Five joints were fabricated using different levels of welding speed (105 mm/min –145 mm/min). From this investigation, it is found that the joints fabricated using a welding speed of 135 mm/min yielded superior tensile properties compared to other joints. The formation of finer grains and higher hardness in fusion zone and uniformly distributed precipitates are the main reasons for the higher tensile properties of these joints

scholarly journals Femtosecond-Laser Assisted Surgery of the Eye: Overview and Impact of the Low-Energy Concept

Micromachines ◽  
2021 ◽  
Vol 12 (2) ◽  
pp. 122
Author(s):  
Catharina Latz ◽  
Thomas Asshauer ◽  
Christian Rathjen ◽  
Alireza Mirshahi
Keyword(s):  
Surgical Techniques ◽  
Numerical Aperture ◽  
Optical Breakdown ◽  
Pulse Frequency ◽  
Low Energy ◽  
Human Cornea ◽  
Energy Concept ◽  
High Pulse Frequency ◽  
Fs Laser ◽  
High Pulse

This article provides an overview of both established and innovative applications of femtosecond (fs)-laser-assisted surgical techniques in ophthalmology. Fs-laser technology is unique because it allows cutting tissue at very high precision inside the eye. Fs lasers are mainly used for surgery of the human cornea and lens. New areas of application in ophthalmology are on the horizon. The latest improvement is the high pulse frequency, low-energy concept; by enlarging the numerical aperture of the focusing optics, the pulse energy threshold for optical breakdown decreases, and cutting with practically no side effects is enabled.

scholarly journals Analysis and optimization of laser drilling process during machining of AISI 303 material using grey relational analysis approach

2021 ◽  
Vol 3 (3) ◽  
Author(s):  
V. Chengal Reddy ◽  
Thota Keerthi ◽  
T. Nishkala ◽  
G. Maruthi Prasad Yadav
Keyword(s):  
Surface Roughness ◽  
Process Parameters ◽  
Grey Relational Analysis ◽  
Pulse Frequency ◽  
Laser Drilling ◽  
Simultaneous Optimization ◽  
Fibre Laser ◽  
Drilling Process ◽  
Relational Analysis ◽  
Grey Relational

AbstractSurface roughness and heat-affected zone (HAZ) are the important features which influence the performance of the laser-drilled products. Understanding the influence of laser process parameters on these responses and identifying the cutting conditions for simultaneous optimization of these responses are a primary requirement in order to improve the laser drilling performance. Nevertheless, no such contribution has been made in the literature during laser drilling of AISI 303 material. The aim of the present work is to optimize the surface roughness (Ra) and HAZ in fibre laser drilling of AISI 303 material using Taguchi-based grey relational analysis (GRA). From the GRA methodology, the recommended optimum combination of process parameters is flushing pressure at 30 Pa, laser power at 2000 W and pulse frequency at 1500 Hz for simultaneous optimization of Ra and HAZ, respectively. From analysis of variance, the pulse frequency is identified as the most influenced process parameters on laser drilling process performance.

scholarly journals Analysis and Implementation of a Frequency Control DC–DC Converter for Light Electric Vehicle Applications

Electronics ◽  
2021 ◽  
Vol 10 (14) ◽  
pp. 1623
Author(s):  
Bor-Ren Lin
Keyword(s):  
Electric Vehicles ◽  
Output Voltage ◽  
Frequency Control ◽  
Input Voltage ◽  
Pulse Frequency ◽  
Switching Frequency ◽  
Battery Charger ◽  
Dc Microgrid ◽  
Load Voltage ◽  
Transportation Vehicle

In order to realize emission-free solutions and clean transportation alternatives, this paper presents a new DC converter with pulse frequency control for a battery charger in electric vehicles (EVs) or light electric vehicles (LEVs). The circuit configuration includes a resonant tank on the high-voltage side and two variable winding sets on the output side to achieve wide output voltage operation for a universal LEV battery charger. The input terminal of the presented converter is a from DC microgrid with voltage levels of 380, 760, or 1500 V for house, industry plant, or DC transportation vehicle demands, respectively. To reduce voltage stresses on active devices, a cascade circuit structure with less voltage rating on power semiconductors is used on the primary side. Two resonant capacitors were selected on the resonant tank, not only to achieve the two input voltage balance problem but also to realize the resonant operation to control load voltage. By using the variable switching frequency approach to regulate load voltage, active switches are turned on with soft switching operation to improve converter efficiency. In order to achieve wide output voltage capability for universal battery charger demands such as scooters, electric motorbikes, Li-ion e-trikes, golf carts, luxury golf cars, and quad applications, two variable winding sets were selected to have a wide voltage output (50~160 V). Finally, experiments with a 1 kW rated prototype were demonstrated to validate the performance and benefits of presented converter.

Sign in / Sign up

Export Citation Format

Share Document