Simple, Sensitive, and Easy to use Method for Determination of Palladium Content in Palladium Acetate Using Flame Atomic Absorption Spectrophotometry

2021 ◽  
Vol 37 (4) ◽  
pp. 880-884
Author(s):  
Melwin Diego D’souza ◽  
Poonam Dwivedi ◽  
Rama Lokhande ◽  
Tushar Anvekar ◽  
Andrew Joseph D’souza
Keyword(s):  
Atomic Absorption ◽  
Method Validation ◽  
Analytical Method ◽  
Method Development ◽  
Limit Of Detection ◽  
Palladium Acetate ◽  
Flame Atomic Absorption ◽  
Relative Standard ◽  
Palladium Content

A simple, sensitive, and easy to use method for the determination of palladium content in palladium acetate was developed using homogeneous acid digestion of palladium acetate followed by atomic absorption spectrometry (AAS) analysis. Parameters affecting the extraction efficiency of palladium during digestion of palladium acetate were investigated and optimized. The palladium content was measured at 244.7 nm by atomic absorption (AA) spectrometers on PinAAcle™ 900 series with an air-acetylene flame. The linear calibration graph was observed in the range of 2.5-15 ppm with a limit of detection of 8.33 ppm and a correlation coefficient of 0.999970. For 5 replicate analyses of each palladium reference solution the relative standard deviation was within 2.00%.Analytical method validation for the method was carried out and obtained results were satisfactory.To verify, the accuracy parameter of the method validation, for the determination of Pd(II) from sample palladium acetate standard addition method was applied and satisfactory results were obtained. Optimization of analytical method variables during analytical method development is discussed.

scholarly journals Determination of cobalt in water samples by atomic absorption spectrometry after pre-concentration with a simple ionic liquid-based dispersive liquid-liquid micro-extraction methodology

2010 ◽  
Vol 8 (3) ◽  
pp. 617-625 ◽  
Author(s):  
Hossein Abdolmohammad-Zadeh ◽  
Elnaz Ebrahimzadeh
Keyword(s):  
Ionic Liquid ◽  
Atomic Absorption Spectrometry ◽  
Atomic Absorption ◽  
Water Samples ◽  
Limit Of Detection ◽  
Absorption Spectrometry ◽  
Experimental Conditions ◽  
Flame Atomic Absorption ◽  
Relative Standard

AbstractA rapid dispersive liquid-liquid micro-extraction (DLLME) methodology based on the application of 1-hexylpyridinium hexafluorophosphate [C6py][PF6] ionic liquid (IL) as an extractant solvent was applied for the pre-concentration of trace levels of cobalt prior to determination by flame atomic absorption spectrometry (FAAS). 1-Phenyl-3-methyl-4-benzoyl-5-pyrazolone (PMBP) was employed as a chelator forming a Co-PMBP complex to extract cobalt ions from aqueous solution into the fine droplets of [C6py][PF6]. Some effective factors that influence the micro-extraction efficiency include the pH, the PMBP concentration, the amount of ionic liquid, the ionic strength, the temperature and the centrifugation time which were investigated and optimized. In the optimum experimental conditions, the limit of detection (3s) and the enrichment factor were 0.70 µg L−1 and 60, respectively. The relative standard deviation (RSD) for six replicate determinations of 50 µg L−1 Co was 2.36%. The calibration graph using the pre-concentration system was linear at levels 2–166 µg L−1 with a correlation coefficient of 0.9982. The applicability of the proposed method was evaluated by the determination of trace amounts of cobalt in several water samples.

scholarly journals A novel LC-MS method development and validation for the determination of phenyl vinyl sulfone in eletriptan hydrobromide

2021 ◽  
Vol 7 (1) ◽  
Author(s):  
Indhu Priya Mabbu ◽  
G. Sumathi ◽  
N. Devanna
Keyword(s):  
Method Development ◽  
Limit Of Detection ◽  
Vinyl Sulfone ◽  
Limit Of Quantification ◽  
Relative Standard ◽  
Pressure Chemical Ionization ◽  
Pressure Chemical ◽  
Development And Validation ◽  
Phenyl Vinyl

Abstract Background The aim of the present method is to develop and validate a specific, sensitive, precise, and accurate liquid chromatography-mass spectrometry (LC-MS) method for the estimation of the phenyl vinyl sulfone in the eletriptan hydrobromide. The effective separation of the phenyl vinyl sulfone was achieved by the Symmetry C18 (50 × 4.6 mm, 3.5 μm) column and a mobile phase composition of 0.1%v/v ammonia buffer to methanol (5:95 v/v), using 0.45 ml/min flow rate and 20 μl of injection volume, with methanol used as diluent. The phenyl vinyl sulfone was monitored on atomic pressure chemical ionization mode mass spectrometer with positive polarity mode. Results The retention time of phenyl vinyl sulfone was found at 2.13 min. The limit of detection (LOD) and limit of quantification (LOQ) were observed at 1.43 ppm and 4.77 ppm concentration respectively; the linear range was found in the concentration ranges from 4.77 to 27.00 ppm with regression coefficient of 0.9990 and accuracy in the range of 97.50–102.10%. The percentage relative standard deviation (% RSD) for six replicates said to be injections were less than 10%. Conclusion The proposed method was validated successfully as per ICH guidelines. Hence, this is employed for the determination of phenyl vinyl sulfone in the eletriptan hydrobromide.

scholarly journals Determination of Copper in Water and Plant Samples by Flame Atomic Absorption Spectrometry After Preconcentration on Octadecyl Silica Membrane Disks Modified with a Recently Synthesized Schiff's Base

2008 ◽  
Vol 91 (4) ◽  
pp. 865-870 ◽  
Author(s):  
Tayebeh Shamspur ◽  
Ali Mostafavi ◽  
Iran Sheikhshoaie
Keyword(s):  
Atomic Absorption Spectrometry ◽  
Atomic Absorption ◽  
Flame Atomic Absorption Spectrometry ◽  
Limit Of Detection ◽  
Absorption Spectrometry ◽  
Minimal Amount ◽  
Aqueous Samples ◽  
Silica Membrane ◽  
Flame Atomic Absorption

Abstract A simple, selective, reliable, and sensitive method for the determination of trace amounts of Cu2+ ions in aqueous samples is proposed. The Cu2+ ions are adsorbed quantitatively during the passage of aqueous samples through an octadecyl (C18) silica membrane disk modified by a symmetrical tetradentate Schiff base ligand, N,N'-bis(4-phenylazo salicylaldimine) 3-chloro-1,2-phenylenediamine (H2L). The retained Cu2+ ions were then stripped from the disk by elution with the minimal amount of nitric acid solution and determined by flame atomic absorption spectrometry. Various parameters, such as the effect of pH, flow rate, type and amount of eluent, and the effects of various cationic interferences on the recovery of ions were studied. The proposed method permitted large enrichment factors (about 550 and higher). The limit of detection of the method was 1.5 102 g/L. The use of the same disk modified with 6 mg H2L for at least 30 times showed no change in the recovery of Cu2+ ions. The accuracy of the method was confirmed by determination of Cu2+ ions in standard samples [National Institute of Environmental Studies (NIES) No. 2 and Nippon Keikinzoku Kogyo (NKK) No. 920]. The results demonstrated good agreement with certified values.

scholarly journals Flame Atomic Absorption Spectrometric Determination of Trace Amounts of Nickel after Extraction and Preconcentration onto Natural Modified Analcime Zeolite Loaded with 2-(5-Bromo-2-Pyridylazo)-5-Diethylaminophenol

2005 ◽  
Vol 88 (3) ◽  
pp. 842-846 ◽  
Author(s):  
Darush Afzali ◽  
Mohammad Ali Taher ◽  
Ali Mostafavi ◽  
Mohammad Khayatzadeh Mahani
Keyword(s):  
Atomic Absorption ◽  
Absorption Spectrometry ◽  
Spectrometric Method ◽  
Final Solution ◽  
Flame Atomic Absorption ◽  
Relative Standard ◽  
Analytical Approaches ◽  
Atomic Absorption Spectrometric ◽  
Reference Samples

Abstract Nickel is a moderately toxic element compared with other transition metals. However, inhalation of nickel and its compounds leads to serious problems, including cancer of the respiratory system and a skin disorder, nickel-eczema. Thus, attention has focused on the toxicity of nickel at low concentrations, and the development of reliable, analytical approaches for the determination of trace amounts of nickel is needed. This paper describes a simple, rapid, and sensitive flame atomic absorption spectrometric method for the determination of trace amounts of nickel in various samples after adsorption of its 2-(5-bromo-2-pyridylazo)-5-diethylaminophenol complex on a modified Analcime column in the pH range of 7.5–10.5. The retained analyte on the Analcime is recovered with 5.0 mL 2M nitric acid and determined by flame atomic absorption spectrometry. The detection limit is 20 ng/mL, and the calibration curve is linear for analyte concentrations in the range of 0.1–8 μg/mL final solution, with a correlation coefficient of 0.9993. Eight replicate determinations of nickel at 2 μg/mL in the final solution gave an absorbance of 0.1222, with a relative standard deviation (RSD) of ±1.2%. The interference of a large number of anions and cations was studied, and the proposed method was used for the determination of nickel in various standard reference samples. The accuracy of the proposed method was evaluated by analyzing standard reference samples, and the results were satisfactory (recoveries of >96%; RSD of <3.5%).

Preparation of Adsorbents Based on Dendrimer Modified Silica Gel and its Adsorption Performances for Lead

2013 ◽  
Vol 800 ◽  
pp. 166-172
Author(s):  
Xiong Zhi Wu ◽  
Li Li ◽  
Fei Ping Li ◽  
Wen Ying Jin
Keyword(s):  
Standard Deviation ◽  
Relative Standard Deviation ◽  
Silica Gel ◽  
Limit Of Detection ◽  
Modified Silica ◽  
Modified Silica Gel ◽  
Flame Atomic Absorption ◽  
Relative Standard ◽  
Separation And Preconcentration

A new sorbent (PAMAM4.0GASG) with gallic acid as functional group has been prepared based on G4.0 polyamidoamine dendrimer modified silica gel (PAMAM4.0SG) and characterized with FTIR. It was employed for selective separation, preconcentration and determination of lead in different samples by flame atomic absorption spectrometry (FAAS). Experimental conditions for effective separation and preconcentration of lead were optimized. The preconcentration factor reaches 200 for lead. The relative standard deviation (R.S.D.) under optimum conditions was 2.1% for 5.0 μg ml1 of Pb (II).The relative standard deviation (R.S.D.) was 2.1% for 5.0 μg ml1 of Pb (II). The limit of detection (LOD) of 0.081μg ml1 was achieved with a sample loading flow rate of 4.2 ml min1 and a 10 ml sample volume in the proposed method. The proposed column enrichment method was applied for the preconcentration/separation and determination of Pb (II) in tap water and river water samples successfully.

scholarly journals Development and Validation of a Green Analytical Method for the Determination of Aspirin and Domperidone Bulk or Formulation Using UV and HPLC

2020 ◽  
Vol 10 (6) ◽  
pp. 49-56
Author(s):  
Sneha Jagnade ◽  
Pushpendra Soni ◽  
Lavakesh Kumar Omray
Keyword(s):  
Analytical Method ◽  
Method Development ◽  
Limit Of Detection ◽  
Research Work ◽  
Ultra Violet ◽  
Limit Of Quantification ◽  
Intermediate Precision ◽  
Rp Hplc ◽  
Development And Validation

The aim of present study was to investigate the development and validation of a green analytical method for the determination of aspirin and domperidone. Method Development and Validation for Estimation of Domperidone and Aspirin in bulk or formulation by using RP-HPLC. The RP-HPLC method was developed for estimation of Aspirin and Domperidone in synthetic mixture by isocratically using 10 mM KH2PO4: Acetonitrile (20:80) as mobile phase, Prontosil C-18 column (4.6 x 250 mm, 5μparticle size) column as stationary phase and chromatogram was recorded at 231 nm. Then developed method was validated by using various parameters such as, linearity, Range accuracy, precision repeatability, intermediate precision, robustness, limit of detection, limit of quantification. The proposed methods were found to be linear with correlation coefficient close to one. Precision was determined by repeatability, Intermediate precision and reproducibility of the drugs. The robustness of developed method was checked by changing in the deliberate variation in solvent. The result obtained shows the developed methods to be Cost effective, Rapid (Short retention time), Simple, Accurate (the value of SD and % RSD less than 2), Precise and can be successfully employed in the routine analysis of these drugs in bulk drug as well as in tablet dosage form. The Simplicity, Rapidly and Reproducibility of the proposed method completely fulfill the objective of this research work. Keywords: Asprin; Domperidone; HPLC; Ultra Violet; Validation

scholarly journals ANALYTICAL METHOD VALIDATION OF ICP-AES FOR ANALYSIS OF CADMIUM, CHROMIUM, CUPRUM, MANGAN AND NICKEL IN MILK

2019 ◽  
pp. 341-344
Author(s):  
DAVID ALEXANDER ◽  
Abdul Rohman
Keyword(s):  
Heavy Metals ◽  
Analytical Method ◽  
Limit Of Detection ◽  
Official Method ◽  
Fast Method ◽  
Limit Of Quantification ◽  
Milk Products ◽  
Relative Standard ◽  
Validation Parameters

Objective: The aim of this research was to validate inductively coupled plasma-atomic emission spectroscopy (ICP-AES) for quantitative analysis of cadmium (Cd), chromium (Cr), cuprum (Cu), mangan (Mn) and nickel (Ni) in milk products. Methods: The heavy metals in milk were determined using ICP-AES at optimized wavelength. The method was validated by assessing several validation parameters which included linearity and range, accuracy, precision and sensitivity expressed by the limit of detection and limit of quantification. The validated method was then used for the analysis of milks commercially available. Results: ICP-AES for determination of Cd, Cr, Cu, Mn, and Ni was linear over a certain concentration range with a coefficient correlation value of>0.997. The limit of quantification values of Cd, Cr, Cu, Mn, and Ni were 0.0047; 0.0050; 0.0066; 0.0061; and 0.0169 µg/ml, respectively. The precision of analytical method exhibited relative standard deviation (RSD) values of 3.18%; 4.17%; 3.05%; 2.93%; and 4.47% during repeatability test and 5.28%; 5.06%; 3.67%; 3.67%; and 11.17% during intermediate precision of Cd, Cr, Cu, Mn, and Ni respectively. The recoveries of these metals assessed using standard addition method were 92.25; 90.88; 102.87; 94.50; and 86.85%, respectively. Conclusion: ICP-AES offered a reliable and fast method for the determination of heavy metals in milk products. The developed method could be proposed as an official method for determination of heavy metals in milk products.

Sign in / Sign up

Export Citation Format

Share Document