scholarly journals Preparation and Conductivity Studies of La9.33Si6O26 (LSO) -Ce0.85Gd0.15O1.925 (CGO15) Composite Based Electrolyte for IT-SOFC

2018 ◽  
Vol 34 (4) ◽  
pp. 2125-2130
Author(s):  
Atiek Rostika Noviyanti ◽  
Iwan Hastiawan ◽  
Diana Rakhmawaty Eddy ◽  
Muhammad Berlian Adham ◽  
Arie Hardian ◽  
...  
Keyword(s):  
Solid Electrolyte ◽  
Operating Temperature ◽  
Weight Ratio ◽  
Solid State Reaction Method ◽  
Intermediate Temperature ◽  
X Ray Diffraction ◽  
X Ray ◽  
Intermediate Temperature Range ◽  
Oxide Ion Conductors ◽  
Oxide Ion

Reducing a high-operating temperature of solid oxide fuel cell (SOFC) to intermediate temperature SOFC (IT-SOFC, 500-750ºC) poses a great challenge in the sense of developing solid electrolyte at intermediate temperature range. In response to this, we report a novel composite La9.33Si6O26 (LSO) - Ce0.85Gd0.15O1.925 (CGO) in this study. The synthesis of LSO-CGO composite was carried out by combining LSO with CGO (9:1, 8:2, and 7:3 in weight ratio) using solid state reaction method. In order to get a dense pellet, all of the products were sintered at 1500°C for 3 h. The X-ray diffraction pattern of sintered pellets show typical patterns for both of LSO and CGO which indicate that the composite was successfully formed. The highest conductivity was detected in 7LSO-3CGO, i.e. 2.10×10-3 S cm-1 at 700 ○C and also has low activation energy (0.60 eV). This result suggests that the LSO-YSZ composites are good oxide ion conductors and may potentially be used as an alternative solid electrolyte in IT-SOFC technology.

MODIFICATION OF LANTHANUM OXYCHLORIDE SOLID ELECTROLYTE FOR CONVENTIONAL POTENTIOMETRIC CHLORINE GAS SENSOR

2011 ◽  
Vol 04 (02) ◽  
pp. 171-174 ◽  
Author(s):  
MAŁGORZATA DZIUBANIUK ◽  
PAWEŁ PASIERB ◽  
MIECZYSŁAW RĘKAS
Keyword(s):  
Solid Electrolyte ◽  
Gas Sensor ◽  
Xrd Analysis ◽  
Solid State Reaction Method ◽  
Electrical Impedance Spectroscopy ◽  
X Ray Diffraction ◽  
X Ray ◽  
Preparation Conditions ◽  
Chlorine Gas ◽  
Source Voltage

La 1-x Mg x OCl 1-x (x = 0.025, 0.05 and 0.1) and La 0.9 Ca 0.1 OCl 0.9 samples were prepared by a solid state reaction method. The best preparation conditions were determined by means of the differential thermal analysis and thermogravimetry (DTA&TG). The samples were studied by X-ray diffraction (XRD) analysis. Electrical conductivity of La 0.9 Mg 0.1 OCl 0.1 was measured using electrical impedance spectroscopy (EIS). The prototype chlorine gas sensor was constructed from La 0.9 Mg 0.1 OCl 0.1 solid electrolyte. The source voltage (SV) of the constructed device was measured as a function of temperature (500–800°C), Cl 2 gradient partial pressure and time. Similar measurements of SV was carried out in atmosphere of synthetic air in argon.

Effect of La Doped on the Conductivity of the Perovskite Type PbZrO3

2012 ◽  
Vol 59 (2) ◽  
Author(s):  
Salmie Suhana Che Abdullah ◽  
Imaduddin Helmi Wan Nordin ◽  
Siti Hawa Mohamed Salleh ◽  
Takao Esaka
Keyword(s):  
Electrical Conductivity ◽  
Single Phase ◽  
Solid State Reaction Method ◽  
X Ray Diffraction ◽  
Emf Measurements ◽  
X Ray ◽  
Perovskite Type ◽  
La Doped ◽  
Oxide Ion ◽  
Lead Site

Electrochemical properties of Pb1-xLaxZrO3+x/2 with perovskite structure have been studied. The powdery Pb1-xLaxZrO3+x/2 has been prepared by solid-state reaction method. The X-ray diffraction analysis reveals that Pb1-xLaxZrO3+x/2 (x = 0.0-0.05) sintered at 900 ˚C was single phase structure. The electrical conductivity of the material has been investigated. By doping La at the lead site, the electrical conductivity of the Pb1-xLaxZrO3+x/2 system decreased. The undoped compound showed the highest electrical conductivity of ca. 10-3 S/cm. Electromotive Force (EMF) measurements of oxygen concentration cell confirm that the charge carrier of La doped PbZrO3 was the oxide ion.

scholarly journals Influence of Li2CO3 addition on electrical and magnetic properties of Ni0.6Mg0.4Fe2O4

2020 ◽  
Vol 10 (03) ◽  
pp. 2050003
Author(s):  
M. R. Hassan ◽  
M. T. Islam ◽  
M. N. I. Khan
Keyword(s):  
Magnetic Properties ◽  
Single Phase ◽  
Low Frequency ◽  
Solid State Reaction Method ◽  
Charge Carriers ◽  
X Ray Diffraction ◽  
X Ray ◽  
Electrical And Magnetic Properties ◽  
Frequency Regime ◽  
Xrd Patterns

In this research, influence of adding Li2CO3 (at 0%, 2%, 4%, 6%) on electrical and magnetic properties of [Formula: see text][Formula: see text]Fe2O4 (with 60% Ni and 40% Mg) ferrite has been studied. The samples are prepared by solid state reaction method and sintered at 1300∘C for 6[Formula: see text]h. X-ray diffraction (XRD) patterns show the samples belong to single-phase cubic structure without any impurity phase. The magnetic properties (saturation magnetization and coercivity) of the samples have been investigated by VSM and found that the higher concentration of Li2CO3 reduces the hysteresis loss. DC resistivity increases with Li2CO3 contents whereas it decreases initially and then becomes constant at lower value with temperature which indicates that the studied samples are semiconductor. The dielectric dispersion occurs at a low-frequency regime and the loss peaks are formed in a higher frequency regime, which are due to the presence of resonance between applied frequency and hopping frequency of charge carriers. Notably, the loss peaks are shifted to the lower frequency with Li2CO3 additions.

Structural evolution of NASICON-type Li1+xAlxGe2−x(PO4)3 using in situ synchrotron X-ray powder diffraction

2016 ◽  
Vol 4 (20) ◽  
pp. 7718-7726 ◽  
Author(s):  
Dorsasadat Safanama ◽  
Neeraj Sharma ◽  
Rayavarapu Prasada Rao ◽  
Helen E. A. Brand ◽  
Stefan Adams
Keyword(s):  
Solid Electrolyte ◽  
Diffraction Study ◽  
Powder Diffraction ◽  
Structural Evolution ◽  
X Ray Diffraction ◽  
X Ray ◽  
Nasicon Type ◽  
Precursor Glass

In situ synchrotron X-ray diffraction study of the synthesis of solid-electrolyte Li1+xAlxGe2−x(PO4)3 (LAGP) from the precursor glass reveals that an initially crystallized dopant poor phase transforms into the Al-doped LAGP at 800 °C.

scholarly journals Investigations of M3Al8O15:Eu3+,Dy3+ (M = Ba, Ca, Mg) phosphors

2016 ◽  
Vol 34 (2) ◽  
pp. 412-417
Author(s):  
Esra Öztürk
Keyword(s):  
Electron Microscopy ◽  
Solid State Reaction Method ◽  
Morphological Characterization ◽  
X Ray Diffraction ◽  
Reaction Method ◽  
X Ray ◽  
Three Samples ◽  
Scanning Electron ◽  
The Eu

AbstractIn this work, aluminate type phosphorescence materials were synthesized via the solid state reaction method and the photoluminescence (PL) properties, including excitation and emission bands, were investigated considering the effect of trace amounts of activator (Eu3+) and co-activator (Dy3+). The estimated thermal behavior of the samples at certain temperatures (> 1000 °C) during heat treatment was characterized by differential thermal analysis (DTA) and thermogravimetry (TG). The possible phase formation was characterized by X-ray diffraction (XRD). The morphological characterization of the samples was performed by scanning electron microscopy (SEM). The PL analysis of three samples showed maximum emission bands at around 610 nm, and additionally near 589 nm, 648 nm and 695 nm. The bands were attributed to typical transitions of the Eu3+ ions.

scholarly journals Pengaruh Suhu Sintering Terhadap Sintesis Silicon Carbide (SiC) Berbahan Dasar Abu Sekam Padi dan Grafit Pensil 2B

2015 ◽  
Vol 5 (01) ◽  
pp. 31
Author(s):  
Resky Irfanita ◽  
Asnaeni Ansar ◽  
Ayu Hardianti Pratiwi ◽  
Jasruddin J ◽  
Subaer S
Keyword(s):  
Electron Microscopy ◽  
Scanning Electron Microscopy ◽  
Silicon Carbide ◽  
Rice Husk Ash ◽  
Sintering Temperature ◽  
Solid State Reaction Method ◽  
X Ray Diffraction ◽  
Reaction Method ◽  
X Ray ◽  
Scanning Electron

The objective of this study is to investigate the effect of sintering temperature on the synthesis of SiC produced from rice husk ash (RHA) and 2B graphite pencils. The SiC was synthesized by using solid state reaction method sintered at temperatures of 750°C, 1000°C and 1200°C for 26 hours, 11.5 hours and 11.5 hours, respectively. The quantity and crystallinity level of SiC phase were measured by means of Rigaku MiniFlexII X-Ray Diffraction (XRD). The microstructure of SiC was examined by using Tescan Vega3SB Scanning Electron Microscopy (SEM). The XRD results showed that the concentration (wt%) of SiC phase increases with the increasing of sintering temperature. SEM results showed that the crystallinity level of SiC crystal is improving as the sintering temperature increases

scholarly journals Structure and electric properties of cerium substituted SrBi1.8Ce0.2Nb2O9 and SrBi1.8Ce0.2Ta2O9 ceramics

2016 ◽  
Vol 10 (3) ◽  
pp. 183-188 ◽  
Author(s):  
Mohamed Afqir ◽  
Amina Tachafine ◽  
Didier Fasquelle ◽  
Mohamed Elaatmani ◽  
Jean-Claude Carru ◽  
...  
Keyword(s):  
Dielectric Constant ◽  
Solid State ◽  
Room Temperature ◽  
Single Phase ◽  
Solid State Reaction Method ◽  
X Ray Diffraction ◽  
Reaction Method ◽  
X Ray ◽  
Lcr Meter ◽  
Curie Temperature Tc

SrBi1.8Ce0.2Nb2O9 (SBCN) and SrBi1.8Ce0.2Ta2O9 (SBCT) powders were prepared via solid-state reaction method. X-ray diffraction analysis reveals that the SBCN and SBCT powders have the single phase orthorhom-bic Aurivillius structure at room temperature. The contribution of Raman scattering and FTIR spectroscopy of these samples were relatively smooth and resemble each other. The calcined powders were uniaxially pressed and sintered at 1250?C for 8 h to obtaine dense ceramics. Dielectric constant, loss tangent and AC conductivity of the sintered Ce-doped SrBi2Nb2O9 and SrBi2Ta2O9 ceramics were measured by LCR meter. The Ce-doped SBN (SBCN) ceramics have a higher Curie temperature (TC) and dielectric constant at TC (380?C and ?? ~3510) compared to the Ce-doped SBT (SBCT) ceramics (330?C and ?? ~115) when measured at 100Hz. However, the Ce-doped SBT (SBCT) ceramics have lower conductivity and dielectric loss.

scholarly journals Making and Characterization of Limnpo4 Using Solid State Reaction Method for Lithium Ion Battery Cathodes

2019 ◽  
pp. 583-588
Author(s):  
Adelyna Oktavia ◽  
Kurnia Sembiring ◽  
Slamet Priyono
Keyword(s):  
Solid State ◽  
Lithium Ion Battery ◽  
Lithium Ion ◽  
Solid State Reaction Method ◽  
Raw Material ◽  
X Ray Diffraction ◽  
Solid State Method ◽  
X Ray ◽  
General Investigation

Hospho-material of olivine, LiMnPO4 identified as promising for cathode material generation next Lithium-ion battery and has been successfully synthesized by solid-state method with Li2Co3, 2MnO2, 2NH4H2PO4 as raw material. The influence of initial concentration of precursors at kalsinasi temperatures (400-800 ° C) flows with nitrogen. The purity and composition phase verified by x-ray diffraction analysis (XRD), scanning electron microscopy (SEM), spectroscopy, energy Dispersive x-ray Analysis (EDS), Raman spectra. General investigation shows that there is a correlation between the concentration of precursors, the temperature and the temperature of sintering kalsinasi that can be exploited to design lithium-ion next generation.

scholarly journals Pengaruh Suhu dan Konsentrasi terhadap Proses Pemisahan Nikel dari Logam Pengotor Menggunakan Metode Leaching

FLUIDA ◽  
2020 ◽  
Vol 13 (2) ◽  
pp. 81-92
Author(s):  
Ade Yanti Nurfaidah ◽  
Dheana Putri Lestari ◽  
Rheisya Talitha Azzahra ◽  
Dian Ratna Suminar
Keyword(s):  
Electron Microscopy ◽  
Scanning Electron Microscopy ◽  
Sulfuric Acid ◽  
Atmospheric Pressure ◽  
Operating Temperature ◽  
Acid Leaching ◽  
X Ray Diffraction ◽  
X Ray ◽  
Pressure Acid Leaching ◽  
Scanning Electron

Abstrak Nikel merupakan unsur logam yang penggunaannya sudah dikenal dalam industri, terutama pada pelapisan logam dan paduan. Pengolahan nikel dari bijih nikel laterit (jenis Limonit) menggunakan proses hidrometalurgi Atmospheric Pressure Acid Leaching (APAL) yang dinilai lebih ekonomis karena pemakaian energi dan biaya operasional cukup rendah. Media pelarut yang digunakan berupa larutan asam sulfat (H2SO4). Sebelum dilakukan pengolahan, karakterisasi bijih dilakukan menggunakan X-Ray Diffraction (XRD), X-Ray Flourscence (XRF), dan Scanning Electron Microscopy (SEM). Metode penelitian yang dilakukan yaitu literature review. Hasil review dari beberapa artikel jurnal menunjukkan bahwa kadar nikel yang terkandung pada suatu bijih sekitar 1,42%, 2,94 dan 0,95% serta sisanya adalah pengotor. Kondisi operasi yang tepat akan menghasilkan pemurnian nikel yang cukup tinggi. Parameter kondisi operasi yang dapat memengaruhi proses pemisahan nikel diantaranya suhu operasi yang ditunjukan dengan semakin meningkatnya % ekstraksi nikel seiring dengan kenaikan suhu. Selain suhu operasi, konsentrasi pelarut juga salah satu parameter yang mempengaruhi % ekstraksi karena semakin tinggi ion H+ akan memudahkan proses pelarutan sehingga akan mengikat Nikel Oksida yang terdapat pada bijih. Suhu paling optimal untuk menghasilkan nikel dengan kemurnian tinggi dalam operasi pelindian atmosferik adalah 90°C dan konsentrasi asam sulfat 5 M.  Kata Kunci: Nikel, pelindian, suhu, konsentrasi   Abstract  Nickel is a metal element whose use is well known in industry, especially in metal and alloy plating. The processing of nickel from laterite nickel ore (Limonite type) uses a hydrometallurgical process of Atmospheric Pressure Acid Leaching (APAL) which is considered more economical because energy consumption and operational costs are quite low. The solvent medium used is a solution of sulfuric acid (H2SO4). Prior to processing, ore characterization was carried out using X-Ray Diffraction (XRD), X-Ray Flourscence (XRF), and Scanning Electron Microscopy (SEM). The research method literature review article. The results of reviews from several journal articles show that the nickel content contained in an ore is around 1.42%, 2.94% and 0.95% and the rest is impurity. The right operating conditions will result in relatively high nickel refining. The operating condition parameters that can affect the nickel separation process include the operating temperature which is indicated by the increasing % nickel extraction along with the increase in temperature. In addition to operating temperature, solvent concentration is also one of the parameters that affects the% extraction because the higher the H+ ion will facilitate the dissolving process so that it will bind to the Nickel Oxide contained in the ore. The optimal temperature to produce high-purity nickel in atmospheric leaching operations is 90°C and a sulfuric acid concentration of 5 M. Keywords: Nickel, leaching, temperature, concentration

Sign in / Sign up

Export Citation Format

Share Document