scholarly journals Electrical Resistance Change Measurement with Elevated Temperature due to Joule Heating for the Detection of Delamination in Graphite/Epoxy Composites

2010 ◽  
Vol 5 (1) ◽  
pp. 15-26 ◽  
Author(s):  
Kosuke TAKAHASHI ◽  
Akira TODOROKI ◽  
Ryosuke MATSUZAKI
Keyword(s):  
Elevated Temperature ◽  
Joule Heating ◽  
Electrical Resistance ◽  
Epoxy Composites ◽  
Resistance Change ◽  
Change Measurement ◽  
Electrical Resistance Change

Pressure and temperature induced electrical resistance change in nano-carbon/epoxy composites

2015 ◽  
Vol 115 ◽  
pp. 1-8 ◽  
Author(s):  
J.T. Shen ◽  
S.T. Buschhorn ◽  
J.Th.M. De Hosson ◽  
K. Schulte ◽  
B. Fiedler
Keyword(s):  
Electrical Resistance ◽  
Epoxy Composites ◽  
Resistance Change ◽  
Nano Carbon ◽  
Electrical Resistance Change

Electrical Failure and Damage Analysis of Multi-Layer Metal Films on Flexible Substrate during Cyclic Bending Deformation

2011 ◽  
Author(s):  
Byoung-Joon Kim ◽  
Hae-A-Seul Shin ◽  
In-Suk Choi ◽  
Young-Chang Joo
Keyword(s):  
Fatigue Resistance ◽  
Electrical Resistance ◽  
Metal Film ◽  
Flexible Substrate ◽  
Resistance Change ◽  
Cyclic Bending ◽  
Capping Layer ◽  
Bending Strain ◽  
Cu Film ◽  
Electrical Resistance Change

Abstract The electrical resistance Cu film on flexible substrate was investigated in cyclic bending deformation. The electrical resistance of 1 µm thick Cu film on flexible substrate increased up to 120 % after 500,000 cycles in 1.1 % tensile bending strain. Crack and extrusion were observed due to the fatigue damage of metal film. Low bending strain did not cause any damage on metal film but higher bending strain resulted in severe electrical and mechanical damage. Thinner film showed higher fatigue resistance because of the better mechanical property of thin film. Cu film with NiCr under-layer showed poorer fatigue resistance in tensile bending mode. Ni capping layer did not improve the fatigue resistance of Cu film, but Al capping layer suppressed crack formation and lowered electrical resistance change. The NiCr under layer, Ni capping layer, and Al capping layer effect on electrical resistance change of Cu film was compared with Cu only sample.

A highly-deformable piezoresistive film composed of a network of carbon blacks and highly oriented lamellae of high-density polyethylene

RSC Advances ◽  
2015 ◽  
Vol 5 (39) ◽  
pp. 31074-31080 ◽  
Author(s):  
Shaodi Zheng ◽  
Jie Deng ◽  
Luqiong Yang ◽  
Danqi Ren ◽  
Wei Yang ◽  
...  
Keyword(s):  
Electrical Resistance ◽  
High Density Polyethylene ◽  
High Density ◽  
Resistance Change ◽  
Carbon Blacks ◽  
Electrical Resistance Change

The electrical resistance change of highly extensible films consisting of a network of carbon blacks in high-density polyethylene, with different regularity of stacked lamellae, is investigated.

Signal conditioning circuit for gel strain sensors

2021 ◽  
Author(s):  
Ismael Payo ◽  
J. L. Polo ◽  
Blanca Lopez ◽  
Diana Serrano ◽  
Antonio M. Rodríguez ◽  
...  
Keyword(s):  
Electrical Resistance ◽  
Pressure Sensors ◽  
Strain Sensors ◽  
Resistance Force ◽  
Electrode Impedance ◽  
Signal Conditioning ◽  
Resistance Change ◽  
Signal Conditioning Circuit ◽  
Conditioning Circuit ◽  
Electrical Resistance Change

Abstract Conductive Hydrogels are soft materials which have been used by some researchers as resistive strain sensors in the last years. The electrical resistance change, when the sensor is stretched or compressed, is usually measured by the two-electrode method. This method is not always suitable to measure the electrical resistance of polymers-based materials, like hydrogels, because it could be highly influenced by the electrode/sample interface, as explained in this study. For this reason, a signal conditioning circuit, based on four-electrode impedance measurements, is proposed to measure the electrical resistance change when the gel is stretched or compressed. Experimental results show that the tested gels can be used as resistance force/pressure sensors with a quite linear behaviour.

Sign in / Sign up

Export Citation Format

Share Document