Determination of crack spacing and crack width in reinforced concrete beams

2003 ◽  
Vol 15 (2) ◽  
pp. 159-180 ◽  
Author(s):  
R. Piyasena ◽  
Yew-Chaye Loo ◽  
Sam Fragomeni
Keyword(s):  
Reinforced Concrete ◽  
Crack Width ◽  
Concrete Beams ◽  
Crack Spacing ◽  
Reinforced Concrete Beams

Experimental study on crack width and crack spacing for Glass-FRP reinforced concrete beams

2017 ◽  
Vol 131 ◽  
pp. 231-242 ◽  
Author(s):  
C. Barris ◽  
L. Torres ◽  
I. Vilanova ◽  
C. Miàs ◽  
M. Llorens
Keyword(s):  
Experimental Study ◽  
Reinforced Concrete ◽  
Crack Width ◽  
Concrete Beams ◽  
Crack Spacing ◽  
Reinforced Concrete Beams ◽  
Glass Frp

scholarly journals Experimental Study on Calculation Methods for Short-term Cracks in High-strength Reinforced Concrete Beams

2017 ◽  
Vol 11 (1) ◽  
pp. 187-194
Author(s):  
Ruliang Zheng ◽  
Degao Tang ◽  
Yulong Xue ◽  
Zhen Liao
Keyword(s):  
Reinforced Concrete ◽  
Crack Width ◽  
Concrete Beams ◽  
High Strength ◽  
Crack Spacing ◽  
Experimental Results ◽  
Reinforced Concrete Beams ◽  
Calculation Methods ◽  
Short Term ◽  
Average Crack

High-strength steel has increasingly become widely used among various engineering practices, but the relevant provisions of the codes lag behind its development. Six sets of experiments on simple supported beams reinforced with HTB600 and HTB700 rebars subject to bending loading were conducted in this study to 1) investigate the conditions of crack development, 2) contrast the calculating modes of short-term crack width between Chinese and European concrete codes, and 3) analyze European applicability and precision pertaining to high-strength reinforcement of beams. According to the experiments and research, when the calculation formulae obtained from Chinese codes were used to calculate the average crack spacing of high-strength reinforced concrete beams, the error relative to that obtained in the experiment reached approximately 20%. Based on this, a revised formula for the calculation of average crack spacing is proposed in this article, and the results of these calculations align with the results obtained from the experiment. In addition, this study also demonstrates that the maximum cracking spacing calculated by adhering to Eurocode standards yielded no significant deviation as compared to the experimental results. However, owing to a difference in the crack width exceeding 20% being observed between the results obtained under Eurocode standards and the experimental results, the calculation methods need to be further improved for better applicability of high-strength reinforced rebars.

Research on Influences of the Coarse Aggregate Size on the Cracks of the Reinforced Beam

2012 ◽  
Vol 503-504 ◽  
pp. 832-836
Author(s):  
Hong Quan Sun ◽  
Jun Ding
Keyword(s):  
Reinforced Concrete ◽  
Crack Width ◽  
Coarse Aggregate ◽  
Concrete Beams ◽  
Fractal Theory ◽  
Aggregate Size ◽  
Reinforced Concrete Beams ◽  
Static Loads ◽  
Reinforced Beams ◽  
Maximum Crack

This paper gives the influences of the coarse aggregate size on the cracks of the beam with different aggregate sizes under static loads. The coarse aggregate sizes are ranked into three classes: small size (4.75mm ~ 19mm), big size (19mm ~ 37.5mm) and mixed size (4.75mm ~ 37.5mm). The developments of cracks of three reinforced concrete beams with the different of coarse aggregate sizes under the static loads are researched. The results show that under the action of the same loads, The reinforced concrete beams with the big aggregate size and mixed aggregate size have almost the same maximum crack width, while the maximum crack width of the beam with small aggregate size is less than formers. Using fractal theory, the fractal dimension of the cracks is studied. The result shows that the aggregate sizes have significant effect to the cracks on the reinforced beams.

THE REINFORCED CONCRETE BEAM DEFLECTION AND CRACKING BEHAVIOR WITH ADDITIONAL FIBER STEEL

2017 ◽  
Vol 4 (1) ◽  
Author(s):  
Faisal Ananda ◽  
Agoes Soehardjono ◽  
Achfas Zacoeb ◽  
Gunawan Saroji
Keyword(s):  
Tensile Strength ◽  
Reinforced Concrete ◽  
Crack Width ◽  
Concrete Beam ◽  
Concrete Beams ◽  
Reinforced Concrete Beam ◽  
Reinforced Concrete Beams ◽  
Beam Deflection ◽  
Cracking Behavior ◽  
Classic Theory

The classic theory mentions that the assessment of deflection and crack width should be taken to minimize those two behaviors. This research itself has the objective to examine whether the additional fiber steel and increased reinforcement ratio has any significant impact on the deflection and existing crack width. This test used the reinforced concrete beams with a size of 15 cm x 25 cm x 180 cm which placed on a simple pedestal. The test was done gradually in every 108 kg until the reinforced yield reached. The fiber increased from 0%, 1.57%, 3.14% and 4.71% while the performance rebar ratio increased from 2 # 10, 2 # 12, and 2 # 14. The result shows that additional 4.71% of maximum fiber decrease compressive strength and rupture modulus while the tensile strength increased. The additional fiber reached a maximum in 4.71% and the additional diameter of 10 mm, 12 mm, and 14 mm increased the deflections and crack width.

Sign in / Sign up

Export Citation Format

Share Document