scholarly journals PROXIMATE ANALYSIS AND CALORIFIC VALUE OF PELLETS IN BIOSOLID COMBINED WITH WOOD WASTE BIOMASS

2018 ◽  
Vol 19 (3) ◽  
pp. 185-190
Author(s):  
I Nyoman Sukarta ◽  
I Dewa Sastrawidana ◽  
Ni Putu Ayuni ◽  
Sudiana I
Keyword(s):  
Calorific Value ◽  
Proximate Analysis ◽  
Wood Waste ◽  
Waste Biomass

scholarly journals Technical, Environmental, and Qualitative Assessment of the Oak Waste Processing and Its Usage for Energy Conversion

2020 ◽  
Vol 12 (19) ◽  
pp. 8113
Author(s):  
Algirdas Jasinskas ◽  
Ramūnas Mieldažys ◽  
Eglė Jotautienė ◽  
Rolandas Domeika ◽  
Edvardas Vaiciukevičius ◽  
...  
Keyword(s):  
Moisture Content ◽  
Calorific Value ◽  
Wood Waste ◽  
Qualitative Assessment ◽  
Herbaceous Plant ◽  
Waste Biomass ◽  
Solid Biofuels ◽  
Solid Biofuel ◽  
Harmful Emissions ◽  
Oak Leaves

The article analyses and evaluates the possibilities of using oak bark, oak leaves, and their mixtures for biofuel. The preparation of this waste for the burning process (milling, granulation) has been investigated and the results have been presented together with the analysis of the prepared granules’ properties—humidity, density, strength, elemental composition, ash content, caloric value, and others. The moisture content of the oak waste granules ranged from 8.1% to 12.5%, and the granules’ density ranged from 975.8 to 1122.2 kg m−3 DM (dry matter). The amount of oak ash found was very high (from 10.4% to 14.7%)—about 10 times higher than that of wood waste granules. The calorific value determined after burning the oak bark and leaves pellets was sufficiently high, ranging from 17.3 to 17.7 MJ kg−1. This thermal value of oak waste granules was close to the calorific value of the herbaceous plant species and some types of wood waste. The environmental impact of burning the granules of oak waste was also assessed. The harmful emissions of carbon monoxide and dioxide, nitrogen oxides, and unburnt hydrocarbons into the environment were found to be below the permissible limits for the incineration of oak waste granules. The highest CO gas concentration, determined when burning the oak leaves, was 1187.70 mg m−3, and the lowest NOx concentration, determined when burning the oak bark and leaf mixture granules, was 341.2 mg m−3. The coefficient of energy efficiency R of the granulated oak leaves biofuel, when the oak waste biomass moisture content was reduced by 10%, reached 3.64. It was very similar to the results of previous studies of various types of granulated straw biofuel (3.5–3.7). The research results presented show that, given that the main parameters of oak waste meet the basic requirements of solid biofuel, oak bark, leaves, and their mixture can be recommended to be used as solid biofuels.

Which One Does Better Predict the Heating Value of Biomass?—Dry Based or As-Received Based Proximate Analysis Results?

2019 ◽  
Vol 141 (11) ◽  
Author(s):  
A. Ozyuguran ◽  
H. Haykiri-Acma ◽  
S. Yaman
Keyword(s):  
Least Squares Method ◽  
Calorific Value ◽  
Absolute Error ◽  
Proximate Analysis ◽  
Prediction Performance ◽  
Bias Error ◽  
Waste Biomass ◽  
Heating Value ◽  
Value Prediction ◽  
Predicted Values

Thirty-nine different species of waste biomass materials that include woody or herbaceous resources as well as nut shells and juice pulps were used to develop empirical equations to predict the calorific value based on the proximate analysis results. Ten different linear/nonlinear equations that contain proximate analysis ingredients including or excluding the moisture content were tested by means of least-squares method to predict the HHV (higher heating value). Prediction performance of each equation was evaluated considering the experimental and the predicted values of HHV and the criteria of MAE (mean absolute error), AAE (average absolute error), and ABE (average bias error). It was concluded that the presence of moisture as a parameter improves the prediction performance of these equations. Also, the samples were classified into two subsets according to their fixed carbon (FC)/ash values and then the correlations were repeated for each subset. Both the full set of samples and the subsets showed a similar trend that the presence of moisture in equations enhances the prediction performance. Also, the FC content may be disregarded from the equation of the calorific value prediction when the FC/ash ratio is lower than a given value.

scholarly journals Characterization of Mexican waste biomass relative to energy generation

BioResources ◽  
2020 ◽  
Vol 15 (4) ◽  
pp. 8529-8553
Author(s):  
José Guadalupe Rutiaga-Quiñones ◽  
Luis Fernando Pintor-Ibarra ◽  
Rocio Orihuela-Equihua ◽  
Nicolás González-Ortega ◽  
María Alejandra Ramírez-Ramírez ◽  
...  
Keyword(s):  
Chemical Elements ◽  
Initial Moisture Content ◽  
Calorific Value ◽  
Volatile Matter ◽  
Proximate Analysis ◽  
Waste Biomass ◽  
Tropical Woods ◽  
Physical And Chemical

In this work, physical and chemical analyses of 28 sawdust samples (tropical woods, pine woods, and oak woods) derived from the primary process of wood transformation and 4 samples of citrus residues were performed, as an option to make densified biofuels. The study included the determination of initial moisture, particle size distribution, proximate analysis, ultimate analysis, calculation of the calorific value, and ash microanalysis. The initial moisture content of the biomass samples ranged from 6.04 to 75.21%. The biomass granulometry results indicate that the highest proportion corresponds to the 1.0-mm (33.10%) (Fraction retained in mesh 0.5 mm). Other results obtained indicate the following ranges: ash content (0.27 to 6.27%), volatile matter (78.90 to 90.50%), fixed carbon (9.10 to 20.44%), carbon (49.13 to 50.78%), oxygen (42.62 to 44.49%), and hydrogen (5.24 to 6.55%). The calculated calorific value ranged from 17.65 MJ/kg to 20.72 MJ/kg. The chemical elements with the highest concentration in the biomass samples were K and Ca, followed in some cases by Al and P. The biomass with the greatest possibilities for making densified biofuels of better quality is the group of pine woods because they have low mineral content, low nitrogen content, and high calorific value.

Evaluasi Prediksi Higher Heating Value (HHV) Biomassa Berdasarkan Analisis Proksimat

2020 ◽  
Vol 4 (1) ◽  
pp. 1-7
Author(s):  
Made Dirgantara ◽  
Karelius Karelius ◽  
Marselin Devi Ariyanti, Sry Ayu K. Tamba
Keyword(s):  
Renewable Energy ◽  
Natural Gas ◽  
Key Words ◽  
Critical Analysis ◽  
Fossil Fuels ◽  
Calorific Value ◽  
Proximate Analysis ◽  
Heating Value ◽  
Bomb Calorimeter ◽  
Hhv Prediction

Abstrak – Biomassa merupakan salah satu energi terbarukan yang sangat mudah ditemui, ramah lingkungan dan cukup ekonomis. Keberadaan biomassa dapat dimaanfaatkan sebagai pengganti bahan bakar fosil, baik itu minyak bumi, gas alam maupun batu bara. Analisi diperlukan sebagai dasar biomassa sebagai energi seperti proksimat dan kalor. Analisis terpenting untuk menilai biomassa sebagai bahan bakar adalah nilai kalori atau higher heating value (HHV). HHV secara eksperimen diukur menggunakan bomb calorimeter, namun pengukuran ini kurang efektif, karena memerlukan waktu serta biaya yang tinggi. Penelitian mengenai prediksi HHV berdasarkan analisis proksimat telah dilakukan sehingga dapat mempermudah dan menghemat biaya yang diperlukan peneliti. Dalam makalah ini dibahas evaluasi persamaan untuk memprediksi HHV berdasarkan analisis proksimat pada biomassa berdasarkan data dari penelitian sebelumnya. Prediksi nilai HHV menggunakan lima persamaan yang dievaluasi dengan 25 data proksimat biomassa dari penelitian sebelumnya, kemudian dibandingkan berdasarkan nilai error untuk mendapatkan prediksi terbaik. Hasil analisis menunjukan, persamaan A terbaik di 7 biomassa, B di 6 biomassa, C di 6 biomassa, D di 5 biomassa dan E di 1 biomassa.Kata kunci: bahan bakar, biomassa, higher heating value, nilai error, proksimat  Abstract – Biomass is a renewable energy that is very easy to find, environmentally friendly, and quite economical. The existence of biomass can be used as a substitute for fossil fuels, both oil, natural gas, and coal. Analyzes are needed as a basis for biomass as energy such as proximate and heat. The most critical analysis to assess biomass as fuel is the calorific value or higher heating value (HHV). HHV is experimentally measured using a bomb calorimeter, but this measurement is less effective because it requires time and high costs. Research on the prediction of HHV based on proximate analysis has been carried out so that it can simplify and save costs needed by researchers. In this paper, the evaluation of equations is discussed to predict HHV based on proximate analysis on biomass-based on data from previous studies. HHV prediction values using five equations were evaluated with 25 proximate biomass data from previous studies, then compared based on error value to get the best predictions. The analysis shows that Equation A predicts best in 7 biomass, B in 6 biomass, C in 6 biomass, D in 5 biomass, and E in 1 biomass. Key words: fuel, biomass, higher heating value, error value, proximate 

Proximate Analysis of British Columbia Herring in Relation to Season and Condition Factor

1939 ◽  
Vol 4b (5) ◽  
pp. 478-490
Author(s):  
John Lawson Hart ◽  
Albert L. Tester ◽  
Desmond Beall ◽  
John P. Tully
Keyword(s):  
British Columbia ◽  
Oil Content ◽  
Condition Factor ◽  
Calorific Value ◽  
Proximate Analysis ◽  
Early Spring ◽  
Different Seasons ◽  
Spawning Time ◽  
Average Condition ◽  
The Individual

Analysis by standard methods of samples of Clupea pallasii from different seasons and localities in British Columbia showed the following ranges in composition: water, 64.2 to 80.2%; oil, 4.1 to 19.4%; protein, 10.1 to 16.8%; ash, 1.9 to 2.8%. Oil content is highest in summer, declines during the fall and winter, and falls to a minimum after spawning time in early spring. There is an accompanying decline in the weight of the fish. Herring are highly variable in calorific value (2.41 to 0.94 Calories per gram). Potential oil yields on reduction as high as 30 gallons per ton are indicated with a minimum of 7 gallons per ton. Average condition factors for samples were determined by averaging the individual condition factors obtained from [Formula: see text], when C is the condition factor, W is weight in grams, L is length in millimetres, and 3.26 is the exponent in the empirically fitted equation W = CLn. This condition factor was found to be positively correlated with oil content and to follow in general the same seasonal trend.

scholarly journals Characteristics of Woody Cutting Waste Briquette with Paper Waste Pulp as Binder

2020 ◽  
Vol 190 ◽  
pp. 00030
Author(s):  
Qurrotin Ayunina Maulida Okta Arifianti ◽  
Azmi Alvian Gabriel ◽  
Syarif Hidayatulloh ◽  
Kuntum Khoiro Ummatin
Keyword(s):  
Moisture Content ◽  
Ignition Time ◽  
Combustion Process ◽  
Calorific Value ◽  
Volatile Matter ◽  
Proximate Analysis ◽  
Hydraulic Press ◽  
Combustion Characteristic ◽  
Paper Waste ◽  
Iron Mold

The current research aimed to increase the calorific value of woody cutting waste briquette with paper waste pulp as binder. There were three different binder variation used in this study, they are 5 %, 10 %, and 15 %. To create a briquette, a cylindrical iron mold with diameter of 3.5 cm and height of 3 cm and a hydraulic press with 2 t power were applied. The physical characteristics of the combination woody waste briquette and paper waste pulp, such as moisture content, ash content, volatile matter and carbon fix were examined using proximate analysis. The calorific value of briquetted fuel was tested by bomb calorimeter. The combustion test was performed to determine the combustion characteristic of briquettes, for example initial ignition time, temperature distribution, and combustion process duration. The general result shows that the calorific value of briquette stood in the range of 4 876 kCal kg–1 to 4 993 kCal kg–1. The maximum moisture content of briquette was 5.32 %. The longest burning time was 105 min.

scholarly journals CHARACTERIZATION OFWASTE BIOMASS FROM GREENHOUSE ROSE CULTIVATION AND PACKAGING

2010 ◽  
Vol 41 (2) ◽  
pp. 29
Author(s):  
Giovanni Cascone ◽  
Alessandro D'Emilio ◽  
Erika Buccellato
Keyword(s):  
Nitrogen Content ◽  
Calorific Value ◽  
Volatile Matter ◽  
Chemical Processes ◽  
The Other ◽  
Waste Biomass

In this work a characterization of the waste biomass originating from a rose cultivation under greenhouse was carried out. Two types of biomass were examined: one made of both branches and leaves, and the other made up only of branches. For each type of biomass the following properties were determined: percentage of carbon, hydrogen and nitrogen, content of moisture, volatile matter and ashes, gross and net calorific value. The results show that the biomass made of only branches has a better quality than the biomass with leaves for use in thermo-chemical processes.

Briquetting of sugarcane bagasse as a proper waste management technology in Vietnam

2020 ◽  
Vol 38 (11) ◽  
pp. 1239-1250
Author(s):  
Anna Brunerová ◽  
Hynek Roubík ◽  
Milan Brožek ◽  
Dinh Van Dung ◽  
Le Dinh Phung ◽  
...  
Keyword(s):  
High Pressure ◽  
Waste Management ◽  
Sugarcane Bagasse ◽  
Calorific Value ◽  
Quality Level ◽  
Waste Biomass ◽  
Direct Combustion ◽  
Mechanical Quality ◽  
Parameters Analysis ◽  
Sugarcane Processing

The present research describes an application of high-pressure briquetting technology to the waste management of sugarcane processing in Vietnam. The amount of generated sugarcane bagasse was monitored during sugarcane processing within the street juice production in Hue city, Vietnam. Generated sugarcane bagasse was subjected to fuel parameters analysis within its suitability for direct combustion. The obtained sugarcane bagasse was converted into bio-briquette fuel by a high-pressure briquetting press and its mechanical quality was determined. Results proved that the proportion of generated sugarcane bagasse from whole sugarcane stem mass was equal to 35.45%. This indicated generation of an abundant amount of sugarcane bagasse worldwide in general. Fuel parameters analysis proved high quality level of low ash content = 0.97% and high calorific values (gross calorific value = 18.35 MJ·kg-1, net calorific value = 17.06 MJ·kg-1), which indicated good suitability for direct combustion processes. Indicators of mechanical quality proved the following observations: mechanical durability = 99.29%, compressive strength = 150.82 N∙mm-1 and bulk density = 1022.44 kg·m-3, with all these indicators representing positive results. In general, the observed results indicated suitability of sugarcane bagasse valorization within the production of bio-briquette fuel by using high-pressure briquetting technology. Finally, analysis of such waste biomass proved its great potential for energy recovery, thus, the advantage of its valorization within the sustainable technologies.

scholarly journals New Utilization of Specific Biomass: Lignin in the Iron Ore Sintering Process

Metals ◽  
2020 ◽  
Vol 10 (9) ◽  
pp. 1170
Author(s):  
Róbert Findorák ◽  
Jaroslav Legemza ◽  
Mária Fröhlichová ◽  
Gabriela Fabriciová ◽  
Martina Džupková
Keyword(s):  
Calorific Value ◽  
Laboratory Research ◽  
Material Research ◽  
Waste Biomass ◽  
Iron Ore Sintering ◽  
Agglomeration Process ◽  
Specific Biomass ◽  
Iron Ore Sintering Process ◽  
Raman And Infrared Spectroscopy ◽  
Coke Powder

The use of lignin can be one of the methods of coke powder substitution in the agglomeration process. This article specifies the material research of lignin and the technological and ecological parameters of the agglomeration process in laboratory conditions using biomass lignin. The methodology of the Raman and infrared spectroscopy, representing a new approach in the analysis and assessment for the purposes of material characteristics for the agglomeration process, was applied to study the structure of carbonaceous matter. The material research of lignin has determined that its calorific value corresponds to ca. 80% of the calorific value of coke powder, while its reactivity is higher than that of the coke. Although the substitution of coke powder using different types of waste biomass (e.g., wood sawdust) in the production of the agglomerate is limited to the maximum of 8–15%, in case of lignin, more than 20% can be substituted, while the standard properties of the produced agglomerate are maintained. The lower emissions of sulfur and nitrogen oxides as well as the reduction of carbon footprint in the agglomeration process as a result of the so-called zero CO2 balance in the formation and processing of the biomass represent its positive aspects. Based on the laboratory research of lignin, up to a 50% substitution of coke powder with this type of biomass can be predicted for the technology of agglomerate production in real operation.

Sign in / Sign up

Export Citation Format

Share Document